1997 PONTIAC FIREBIRD parking brake

System Warning Light” and “Towing Your Vehicle” in Anti-Lock 1- System Warning Eight
the Index.)
Your braKe s cem may not be working properly
if the brake system warning light is on. Driving
~ with the brake system warning light on can lead
to an accident.
If the light is still on or if the
anti-lock brake system warning light
is flashing
after
you’ve pulle’d of€ the road and stopped
~
!
ABS
INOP
With the anti-lock brake
system, this light will come
on when you start your
engine and it will stay
on for three seconds.
That’s normal.
carefully, have the vehicle towed for service. If the light flashes when you’re driving, you don’t have
anti-lock brakes and there could be
a problem with your
regular brakes. Pull off the road and stop carefully. You
When the ignition is on* the brake system warning light may notice that the pedal is harder to push. or, the pedal
on when YOu set Your Parking brake* The may go closer to the floor, It may take longer to stop,
light will stay
on if your parking brake doesn’t release Have the vehicle towed for service. (See “Towing Your
fully.
If it stays on after your parking brake is fully Vehicle” in the Index.)
released, it means you have
a brake problem.
2-80

Parking on Hills
You really should not park your vehicle, with a trailer
attached, on a hill.
If something goes wrong, your rig
could start to move. People can be injured, and both
your vehicle and
the trailer can be damaged.
But if you ever have to park your rig on a hill, here’s
how to do it:
1. Apply your regular brakes, but don’t shift into
PARK (P) yet, or into gear for a manual transmiss’ion.
2. Have someone place chocks under the trailer wheels.
3, When the wheel C~OGBS are in place, release the
regular brakes until the chocks absorb the load.
4. Reapply the regular brakes, Then apply your parking
brake, and then shift to
PARK (P), or REVERSE (R)
for a manual transmission.
5. Release the regular brakes.
When You Are Ready to Leave After
Parking on a Hill
1. Apply your regular brakes and hold the pedal down
while
you:
Start your engine;
Shift into a gear; and
Release the parking brake.
2. Let up on the brake pedal.
3. Drive slowly until the trailer is clear of the chocks.
4. Stop and have someone pick up and store the chocks.
Maintenance When Trailer Towing
Your vehicle will need service more often when you’re
pulling a trailer. See the Maintenance Schedule for more
on this. Things that are especially important in trailer
operation
are automatic transmission fluid (don’t
overfill), engine oil, axle lubricant, belts, cooling system
and brake adjustment. Each
of these is covered in this
manual, and the Index will help you find them quickly,
If you’re trailering, it’s a good idea to review these
sections before
you start your trip.
Check periodically to see that all hitch nuts and bolts
are tight.
4-38

To help avoid injury to you or others:
Never let passengers ride in a vehicle that is
0 Never tow faster than safe or posted speeds.
Never tow with damaged parts not
fully secured.
0 Never get under your vehicle after it has
been lifted
by the tow truck.
Always secure the vehicle on each side with
separate safety chains when towing it.
0 Never use J-hooks, Use T-hooks instead.
being towed.
A vehicle
can fall from a car car
adequately secured. This can cause a collision,
serious personal injury and vehicle damage. The
vehicle should be tightly secured with chains or
steel cables before
it is transported.
Don’t use substitutes (ropes, leather straps,
canvas webbing, etc.) that can be cut by sharp
edges underneath the towed vehicle. Always use
T-hooks inserted in the T-hook slots. Never use
J-hooks, They will damage drivetrain and
suspension components.
When your vehicle is being towed, have the ignition key
turned to the
OFF position. The steering wheel should
be clamped in a straight-ahead position, with a clamping
device designed for towing service.
Do not use the
vehicle’s steering column
lock for this. The transmission
should
be in NEUTRAL (N) and the parking
brake released.

If a Tire Goes Flat
It’s unusual for a tire to ‘‘blow out’’ while you’re driving,
especially if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But
if you should ever have a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the flat tire will create a drag that
pulls the vehicle toward that side. Take your foot off the
accelerator pedal and
grip the steering wheel firmly,
Steer to maintain lane position, and then gently brake to
a st,ot, well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control
by
steering the way you want the vehicle to go, It may be
very bumpy and noisy, but you can still steer. Gently
brake
to a stop -- well off the road if possible,
If
a tire goes flat, the next part shows how to use your
jacking equipment to change a flat tire safely.
Changing a Flat Tire
If a tire goes flat, avoid further tire and wheel damage
by driving slowly t,o a level place.
Turn on your hazard
warning flashers.
Cham- ng a tire can cause an injury. The vehicle
can
slip off the jack and roll over you or other
people. You and they could be badly injured.
Find
a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly,
2. Put an automatic transmission shift lever in
PARK (P), or shift a manual transmission tu
FIRST (1) or REWRSE (R).
3. Turn off the engine.
To be even more certain the vehicle wan? move,
you can put blocks at the front and rear of the
tire farthest away from the one being changed.
That would
be the tire on the other side of the
vehicle, at the opposite ~ end,
5-26

Checking the Fluid Hot or Cold
I) Park your vehicle on a level place. Keep the
0 With the parking brake applied, place the shift lever
engine running.
in PARK (P).
With your foot on the brake pedal, move the shift
lever through each gear range, pausing for about
three seconds in each range. Then, position the shift
lever in
PARK (P).
Let the engine run at idle for three minutes or more.
Then, without shutting off the engine, follow these steps:
3800 Engine Transmission Dipstick
6-24

Relay
B
C
D
E
F
G
H
J
Usage
Air Conditioning Compressor Anti-Lock Brake SystedTraction Control
System
(TCS)
Cooling Fan 1
AIR Pump
Cooling Fan 2
Not Used
Fog
Lamps
Cooling Fan 3
Replacement Bulbs
Back-up . . . . . . . . . . . . . . . . . . .
Center High-Mounted Stoplamp . .
Front Parking and Turn Signal . .
Headlamp . . . . . . . . . . . . . . . .
Sidemarker . .
Tail Only . . . . .
Tail/Stop/Turn . . .
. . . . . . . . 1156
e.* . . 921
. . . . . . . . . 3157K
. . . . . . H-6545
, . . . . . . . . . . 194
.., .. . . . . . . . . . 194
.................. . 2057
Capacities and Specifications
Engine
Type
VIN Engine Code
K . . .
VIN Engine Code P .
Fuel Delivery . . . . . . . .
...... V6
. * . , . e. . V8
. . . . . . . . Fuel Injection
Valve Arrangement
. . . . .
Piston Displacement
VIN Engine Code K . . .
VIN Engine Code P . . . . .
Firing Order
VIN Engine Code K . . .
VIN Engine Code P .
.., . . . . In-Head
, . ,231 CID (3800)
, , . 350 CID (5.7L)
, . . 1-6-5-4-3-2
.... 1-8-4-3-6-5-7-2
Wheel Nut Torque
. . . . . . . . . . . 100 lb-ft (140 N-m)
Windshield Wiper Blade Replacement
Type
. . . . . ........................ hook
Length
. . . ..... . 24 inches (610 mm)

Starter Switch Check When
you are doing this check, the vehicle could
move suddenly.
If it does, you or others could be
injured. Follow the steps below. Brake-Transmission Shift Interlock
(BTSI) Check
(Automatic Transmission)
1.
2,
3.
Before you start, be sure you have enough room
around the vehicle.
Firmly apply
both the parking brake (see “Parking
Brake” in the Index if necessary) and the regular brake.
NOTE: Do not use the accelerator pedal, and be
ready to turn off the engine immediately if it starts.
On automatic transmission vehicles, try to start the
engine in each
gear. The starter should work only in
PARK (P) or NEUTRAL (N). If the starter works in
any other position, your vehicle needs service.
On manual transmission vehicles, put the
shift lever
in
NEUTRAL (N), push the clutch down halfway
and try to start the engine. The starter should work
only when the clutch is
pushed down all the way to
the floor. If the starter works when the clutch isn’t
pushed
all the way down, your vehicle needs service.
When you are doing this check, the vehicle could
move suddenly. If it does, you or others could be
injured. Follow the steps below.
1.
2.
3.
Before you start, be sure you have enough room
around the vehicle. It should be parked
on a
level surface.
Firmly apply the parking brake (see “Parking Brake”
in the Index if necessary).
NOTE: Be ready to apply the regular brake
immediately
if the vehicle begins to move.
With the engine off, turn the key to the RUN
position, but don’t start the engine. Without applying
the regular brake, try to move the shift lever out of
PARK (P) with normal effort. If the shift lever
moves out
of PARK (P), your vehicle’s BTSI
needs service.
7-46

Ignition Transmission Lock Check
While parked, and with the parking brake set, try to turn
the ignition key to LOCK in each shift lever position.
0 With an automatic transmission, the key should turn
to LOCK only when the shift lever is in
PARK (P).
LOCK only when the shift lever is in REVERSE (R).
With a manual transmission, the key should turn to
On vehicles with a key release button, try to turn the key
to LOCK without pressing the button. The key should
turn to LOCK only when you press the key button.
On all vehicles, the key should come out only in LOCK.
Parking Brake and Automatic Transmission
PARK (P) Mechanism Check
I
When you are doing this check, your vehicle
could begin to move. You or others could be
injured and property could be damaged. Make
sure there is
room in front of your vehicle in case
it begins to roll. Be ready to apply the regular
brake at once should the vehicle begin to move.
Park on a fairly steep hill, with the vehicle facing
downhill. Keeping your foot on the regular brake, set the
parking brake.
e
a
To check the parking brake’s holding ability:
With the engine running and transmission in
NEUTRAL
(N), slowly remove foot pressure from
the regular brake pedal.
Do this until the vehicle is
held by the parking brake only.
To check the PARK (P) mechanism’s holding ability:
With the engine running, shift to
PARK (P). Then
release all brakes.
Underbody Flushing Service
At least every spring, use plain water to flush any
corrosive materials from the underbody. Take care to
clean thoroughly any
areas where mud and other debris
can collect.