1997 PONTIAC FIREBIRD light

Parking Brake
To set the parking brake, hold the brake pedal down and
pull up on the parking brake lever.
If the ignition is on,
the brake system
warning light will come on.
To release the parking brake, hold the brake pedal down.
Pull the parking brake lever up until you can push in the
release button. Hold the release button in as you move
the brake lever all the way down.
2-37

Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the,lever all the way up or down.
When the turn
is finished, the lever will return
automatically.
An arrow
on the instrument
panel will flash in the
direction of the turn
or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release
it.
As you signal a turn or a lane change, if the arrows don’t
flash but just stay on,
a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the
fuse (see “Fuses and Circuit
Breakers” in the Index).
Headlamp High/Low Beam
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward
you. Then release it.
When the high beams are
on, this light
on the
instrument panel also will
be on.
2-45

Windshield Wipers
You control the windshield wipers by turning the band
with the wiper
symbol on it.
For a single wiping cycle, turn the band to MIST. Hold
it there until
the wipers start, then let go. The wipers will
stop
after one cycle. If you want more cycles, hold the
band
on MIST longer.
You can set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain or
snow. Turn the band
to choose the delay time. The
closer to LO, the shorter the delay.
For steady wiping at low speed, turn the
band away
from
you to the LO position, For high-speed wiping,
turn the band further, to
HI, To stop the wipers, move
the band
to OFF.
Damaged wiper blades may prevent you from seeing
well enough to drive safely.
To avoid damage, be sure to
clear ice and snow from the wiper blades before using
them.
If they’re frozen to the windshield, carefully
loosen
or thaw them. If your blades do become
damaged, get new blades
or blade inserts,
Heavy
snow or ice can overload your wipers. A circuit
breaker will
stop them until the motor cools. Clear away
snow or ice to prevent an overload.
2-46

Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
0
0
rn
Use the accelerator pedal to get to the higher speed.
Push the button at the end of the lever, then release
the button and the accelerator pedal. You’ll now
cruise at the higher speed.
To increase your speed in very small amounts, move
the switch to
WA for less than half a second and then
release it. Each time you do this, your vehicle will
go
about 1 rnph (1.6 kmh) faster.
Move the cruise switch from
ON to WA. Hold it
there until you get up
to the speed you want, and
then release the switch.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
0
e
Push in the button at the end of the lever until you
reach the lower speed you want, then release it.
To slow down in very small amounts, push the
button for less than half a second. Each time you do
this, you’ll
go 1 mpk (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot
off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness
of the hills.
When going up steep hills,
you may have to step on the
accelerator pedal
to maintain your speed. When going
downhill, you may have to brake or shift to
a lower gear
to keep your speed down. Of course, applying the brake
takes
you out of cruise control. Many drivers find this to
be
too much trouble and don’t use cruise control on
steep hills.
Ending Out of Cruise Csntrol
There are several ways to turn off the cruise control:
rn Step lightly on the brake pedal or push the clutch
pedal, if
you have a manual transmission ; OR
rn Movk the cruise switch to OFF.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
2-50 ~-

Lamps
II
The main lamp control is a knob that works these lamps:
Headlamps
Taillamps
Parking lamps
License lamps
Sidemarker lamps
Instrument panel lights
-'Q- , This setting turns on your headlamps and other
operating lamps.
pi This setting turns on your parking lamps without
your headlamps.
Turn the knob to OFF to turn off the lamps.
0
Headlamps On Reminder
If you turn the ignition off and leave the lamps on, you
will hear
a chime lasting up to 5 seconds. If the lamps
are still on when you open the driver's door, the chime
will sound again.
2-51

Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
In Canada, a light sensor on top of the instrument
panel automatically turns the headlamps on,
so be
sure it isn’t covered.
The DRL system will make your front turn signal lamps
come on when:
The ignition is on,
The headlamp switch is OFF and
0 The parking brake is released.
When
the DRL are on, only your front turn signal lamps
will be on. The taillamps, sidemarker and other lamps
won’t be on.
Your instrument panel won’t be lit up either.
For Canadian vehicles when it’s dark enough outside,
your front turn signal lamps will go out and your
headlamps will come on. The other lamps that come on
with your headlamps will also come on. When it’s bright
enough outside, the regular lamps will go off, and your
front turn signal lamps will come on. On a non-Canadian vehicle the headlamps have
to be
turned on manually when you need them. When the
headlamps are turned
on, the front turn signal lamps
will go out. When you use your turn signals, the front
turn signal lamp and the taillamp on the desired side
will flash.
As with any vehicle, you should turn OM the regular
headlamp system when you need it.
Fog Lamps (If Equipped)
Use your fog lamps for better vision in foggy or misty
conditions. Your parking lamps must be on or your fog
lamps won’t work.
0s To turn the fog lamps on, push the right side of the
fog lamp switch. Push the left side of the switch to turn
the fog lamps
off. A light on the switch will come on
when the fog lamps are on.
Fog lamps will go off whenever your high beams come
on. When the high beams
go off, the fog lamps will
come on again.
If your vehicle is equipped with the Vehicle and Content
Theft-Deterrent System and your fog lamp switch is on,
the fog lamps may flash to indicate operation of the
Vehicle and Content Theft-Deterrent System. See “Vehicle
and Content Theft-Deterrent System” in the Index.
2-53

Interior Lamps
Instrument Panel Brightness Control
This switch controls the brightness of your
instrument panel lights. Turn the switch upward
to
brighten or dim the lights, If you turn the switch all the
way up, your courtesy lamps will come on.
Courtesy Lamps
When any door is opened, several interior lamps go on.
These lamps are courtesy lamps. They make
it easier for
you
to enter and leave your vehicle.
Courtesy lamps include the dome lamp and other lamps
throughout the interior
of your vehicle.
To prevent battery rundown, your interior lamps will be
disabled about
10 minutes after the ignition is turned to
OFF. The 10 minute timer will be restarted if you do any
of the following;
1, Turn the ignition on.
2. Open either door.
3. Press any button on your Remote. Lock
Control transmitter.
4. Turn the int’erior lamp switch from off to on.
5. Open the hatch.
Delayed Illumination
With delayed illumination, the courtesy lamps will stay
on for
25 seconds after you close the doors when
entering the vehicle. They will stay
on for five seconds
after you close the doors when exiting the vehicle. The
times will
be shortened if the ignition is turned to the
RUN position or if the power locks are activated. To
turn this feature on or off, see “Feature Customizatian”
in the Index.
Exit Lighting
With exit lighting, the interior lamps will come on when
you remove the key from the ignition
to help you see
while exiting the vehicle.
To turn this feature on or off,
see “Feature Customization” in the Index,
2-54

When carrying large or heavy items, it is a good idea to
open the panel and place the items in the rear area.
I An improperly stored close-out panel could be
thrown about the vehicle during
a collision or
sudden maneuver. You
or others could be
injured. If you remove the cover, always store it
outside your vehicle. When you put it back,
always be sure that it is securely reattached.
Ashtray and Lighter
Lift up the cover to open the ashtray. To remove it, lift
up on either side
of the ashtray. If you have an automatic
transmission, the ashtray
is near the front of your
console.
If you have a manual transmission, the ashtray
is near your cupholder.
I NOTICE:
Don’t put papers and other things that burn into
your ashtray.
If you do, cigarettes or other
smoking materials could set them on
fire,
causing damage.
To use the lighter, push it in all the way and let go.
When it’s ready, it will pop back by itself.
2-59