1997 MITSUBISHI TRITON Workshop Manual

L
ock le ve r L
ock s p rin g T
o c lo ck s p rin g T
o b ody w ir in g
h arn ess

GENERAL ± Supplemental Restraint System (SRS)00-31
Harness connector
(No. of terminals,
colour)SDU
terminal
No.Destination of harnessCorrective action
2 pins, red1, 2Body wiring harness
Clock springReplace clock spring
±3, 4±±
±5, 6±±
14 pins, red7, 8±±
9Body wiring harness
Diagnosis connectorCorrect or replace each
wiring harness
10Body wiring harness
Front wiring harness

Ignition switch (ST)
wiring harness
11Body wiring harness
Junction block (fuse No. 11)
12Body wiring harness
Junction block (fuse No. 10)
13Body wiring harness
Combination meter (SRS
warning lamp)
14±±
15Body wiring harness
Front wiring harness

Front impact sensor (+) (R.H.)Sensor cable* installa-
tion procedures
(Refer to GROUP 52B )16Body wiring harness
Front wiring harness

Front impact sensor (+) (L.H.)(Refer to GROUP 52B.)
17Body wiring harness
Front wiring harness

Front impact sensor (±) (L.H.)
18Body wiring harness
Front wiring harness

Front impact sensor (±) (R.H.)
19, 20Body wiring harness
EarthCorrect or replace each
wiring harness
NOTE
The sensor cable marked with * is available as service part.
7. SRS components should not be subjected to heat over 93
C, so remove the SRS-diagnosis unit,
air bag module, clock spring and front impact sensors before drying or braking the vehicle after painting.
8. Whenever you finish servicing the SRS, check warning lamp operation to make sure that the system
functions properly. (Refer to GROUP 52B ± SRS Maintenance.)
9. Make certain that the ignition switch is OFF when the MUT-II is connected or disconnected.
10. If you have any questions about the SRS, please contact your local distributor.
NOTE
SERIOUS INJURY CAN RESULT FROM UNINTENDED AIR BAG DEPLOYMENT, SO USE ONLY
THE PROCEDURES AND EQUIPMENT SPECIFIED IN THIS MANUAL.

S
U PPO RT L O CATIO NS F O R L IF TIN G A ND J A CKIN G 00100070058
C au tio n
D o n ot s u pport t h e v eh ic le s a t lo catio ns o th er t h an s p ecif ie d s u pportin g p oin ts . If d o s o , t h is
w ill c au se d am ag e, e tc .
S U PPO RT P O SIT IO NS F O R A G ARAG E J A CK A ND A XLE S TA NDS
< 2W D> A
XLE S TA NDS
G ARAG E J A CK

A
XLE S TA NDS
G ARAG E J A CK

GENERAL ± Standard Parts-tightening-torque Table00-36
STANDARD PARTS-TIGHTENING-TORQUE TABLE00100110033
Each torque value in the table is a standard value
for tightening under the following conditions.
(1) Bolts, nuts and washers are all made of steel
and plated with zinc.
(2) The threads and bearing surface of bolts and
nuts are all in dry condition.The values in the table are not applicable:
(1) If toothed washers are inserted.
(2) If plastic parts are fastened.
(3) If bolts are tightened to plastic or die-cast
inserted nuts.
(4) If self-tapping screws or self-locking nuts are
used.
Standard bolt and nut tightening torque
Thread sizeTorque Nm
Bolt nominal
diameter (mm)Pitch (mm)Head mark ª4ºHead mark ª7ºHead mark ª8º
M50.82.54.95.9
M61.04.98.89.8
M81.25122225
M101.25244452
M121.25418196
M141.572137157
M161.5111206235
M181.5167304343
M201.5226412481
M221.5304559647
M241.5392735853
Flange bolt and nut tightening torque
Thread sizeTorque Nm
Bolt nominal
diameter (mm)Pitch (mm)Head mark ª4ºHead mark ª7ºHead mark ª8º
M61.04.99.812
M81.25132428
M101.25264957
M101.5244454
M121.254693103
M121.75428196