1997 Mercury Sable bulb

²At least ten minutes of driving on an expressway
or highway.
Before completing the above driving modes, the
engine must be warmed up and at operating
temperature. Once started, the vehicle must not be
turned off during these driving modes.
EXTERIOR LAMPS
It is a good idea to check the operation of the
following lights frequently:
²Headlamps
²High-mount brake lamp
²Tail lamps
²Brake lamps
²Backup lamps
²Hazard flashers
²Turn signals
²License plate lamp
²Interior overhead lamps
Do not remove lamp bulbs unless they will be
replaced immediately. If a bulb is removed for an
extended period of time, contaminants may enter
the lamp housings and affect performance.
High-mount brake lamp - Sedan
To remove the brake lamp:
1. Remove package
tray trim, then push
attachment toward the
rear.
2. Slide brake lamp up
and away from the rear
window to remove it
from the tabs that hold
it down.
3. Disconnect bulbs.
dno_drive-cycle
dno_exterior-bulbs
Maintenance and care
140

To install brake lamp:
1. Install bulbs, then position the brake lamp over
tab slots and line up the tab with the tab slots.
2. Push down and toward the rear window to engage
the tabs.
3. Push attachment toward the rear window and line
up slot in attachment with the edge of the sheet
metal screw.
4. Release the attachment slot onto the sheet metal
hole. Install the package tray trim.
High-mount brake lamp - Wagon
To remove the brake lamp:
1. Remove interior trim
panel, then remove the
three attachment nuts
that hold brake lamp in
place.
2. Lift whole assembly
off vehicle from the
outside.
3. Disconnect bulbs.
To install brake lamp:
1. Install bulbs, the position brake lamp into tailgate
holes.
2. From the inside of the vehicle, stall and tighten
the four nuts that hold the brake lamp in place.
3. Install the interior trim panel.
Using the right bulbs
Function Trade Number
Front side marker lamp 194
Front park/turn lamp 3457NA
Headlamp 9007
Tail lamp/brake lamp 3157
Maintenance and care
141

Function Trade Number
Heater-A/CGo to Ford
authorized
dealer
Automatic climate controlGo to Ford
authorized
dealer
Rear window defrost switchGo to Ford
authorized
dealer
Rear window wiper/washer
switch (wagon)Go to Ford
authorized
dealer
Headlamps
To remove the headlamp bulb:
1. Make sure headlamp switch is in OFF position,
then open the hood. If you are replacing the driver
side headlamp, unclip the electronic module on the
right side of the battery and move it out of the way.
2. Remove the
electrical connector
from the bulb by
pulling the connector.
3. Remove the bulb
retaining ring by
rotating it
counterclockwise
(when viewed from the
rear) about an eighth
of a turn to free it from
the bulb socket, and by
sliding the ring off the
Maintenance and care
143

plastic base. Keep the ring because it will be used
again to retain the new bulb.
4. Remove the old bulb from its socket by gently
pulling it straight back out of the socket. Do not
turn the bulb while you are removing it.
To install the new bulb:
1. With the flat side of
the bulb's plastic base
facing upward, insert
glass end of the bulb
into the socket. You
may need to turn the
bulb left or right to line
up the grooves in the
plastic base with the
tabs in the socket. When the grooves are aligned,
push the bulb into the socket until the plastic base
contacts the rear of the socket.
2. Slip the bulb retaining ring over the plastic base
until it contacts the rear of the socket by rotating it
clockwise until you feel a ªstop.º
3. Push the electrical connector into the rear of the
plastic base until it snaps, locking it into position.
4. Turn the headlamps on and make sure they work
properly. If the headlamp was correctly aligned
before you changed the bulb, you should not need to
align it again.
AIMING THE HEADLAMPS
Your vehicle is equipped with a Vehicle Headlamp
Aim Device (VHAD) on each headlamp body. Each
headlamp may be proeprly aimed in the horizontal
direction (left/right) and the vertical position
(up/down).
A non-zero bubble reading does not necessarily
indicate out-of-aim headlamps. If your vehicle is not
positioned on a level surface, the slope will be
included in the level indicator. Therefore, vertical
headlamp adjustment should be performed only
dno_formality
Maintenance and care
144

quality .................... 136
safety information
relating to automotive
fuels ....................... 134
Fuel gauge ................. 12
Fuel pump shut-off
switch .................... 21,96
Fuse panels
instrument panel .... 98
power
distribution box .... 102
Fuses .......................... 97
Gauges, Mechanical
engine coolant
temperature gauge . 11
Hazard flashers .... 26,96
Headlamps
flashing .................... 26
high beam ............... 25
turning on and off .. 13
Hood ........................ 116
Ignition
positions of the
ignition .................... 21
Instrument cluster ...... 6
Jump-starting your
vehicle ............... 110,111
attaching cables .... 110
disconnecting cables 112
Keyless entry system
autolock ................... 39
keypad ..................... 37
locking and unlocking
doors ........................ 38
programming entry
code ......................... 37
Lamps ........................ 13
instrument panel,
dimming ................... 13
map lamps ............... 27
replacing bulbs .... 140,
141,143Liftgate
remote release ........ 34
Lights, warning and
indicator
air bag ........................ 9
anti-lock
brakes (ABS) ....... 8,81
brake .......................... 9
charging system ........ 9
cruise indicator ......... 8
door ajar .................... 7
engine oil pressure ... 9
high beam ................. 6
low coolant ................ 7
low fuel ...................... 7
overdrive off .............. 8
safety belt ................. 7
service engine soon .. 7
Lubricant
specifications ........... 154
Luggage rack ............. 36
Mirrors
heated ...................... 30
side view mirrors
(power) ................... 30
Moon roof .................. 27
Motorcraft parts ...... 151
Odometer ................... 11
Parking brake ............ 82
Phone, cellular .......... 33
Power door locks ...... 29
Power steering
fluid, checking and
adding .................... 124
Rear window
defroster .................. 20
Refill capacities for
fluids ........................ 152
Relays ...................... 104
Remote entry system 41
Index
164