AR88.70-P-9020GI
Remove/install mirror glass
24.4.01
MODEL
163.113 /154 /174 #A as of 289565,
163.113 /154 /174 #X as of 754620,
163.128 /157 /175
P88.70-2126-11
1
Locking mechanism
2
Mirror glass
3
Housing
Removing and installing
1
Remove outside rearview mirror covering
AR88.70-P-9040GI
2
Open locking mechanism (1)
3
Separate mirror glass (2) from housing (3)
Separate carefully to avoid braking
retaining clips.
Installation:
Ensure that retaining clips
catch properly.
4
Disconnect electrical connectors from mirror
heater
3 electrical connectors.
5
Install in the reverse order
Copyright DaimlerChrysler AG 04.08.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 1
2
Drain the coolant
Engine 611.960/961/962,
612.961/962/967/990, 613.960/961,
628.960/961/963, 646, 647, 648
AR20.00-P-1142HB
Engine 612.963
AR20.00-P-1142M
3
Remove coolant thermostat (20)
Engine 611, 612, 613, 646, 647, 648
AR20.10-P-2460PP
Engine 628.960/963
AR20.10-P-2460M
4
Mount the housing to remove oil and flush the
cooling/heating system
The housing may be used only for the
purpose of removing the oil, and must be
removed again after it has been rinsed.
Engine 611.960/961/962/ 612.961/962
/963/967/990, 613.960/961
*BA20.10-P-1005-01A
Engine 628.960/961/962/963
*BA20.10-P-1002-01F
Engine 646.962/963
*BA20.10-P-1002-01G
y
Housing for removing oil and flushing the
cooling/heating system
WF58.50-P-2000-01A
Cleaning
5
Set the heater control to full power
6
Set the auxiliary heater to full power
7
Fill the cooling/heating system with a rinsing
solution
Rinsing solution consisting of 5% cleaning
agent and 95% water.
*BF20.00-P-1001-02E
Cleaning agent
*BR00.45-Z-1001-04A
8
Warm up the engine to operating temperature
at moderate engine speed
While engine is running, hold operating
temperature at 80 °C for about 5 min.
9
Switch off engine and allow the cooling
system to
cool to about 50 °C
10
Drain the rinsing solution completely at the
drain plug of radiator (18)
Observe the environmental instructions of
the manufacturer of the cleaning agent.
11
Fill cooling system with fresh water
Pour fresh water into the coolant
expansion reservoir (1).
12
Warm up the engine to operating temperature
at moderate engine speed
While engine is running, hold the
operating temperature at 80 °C for about
5 min.
13
Drain the fresh water completely at the drain
plug of radiator (18)
Repeat the flushing process until all of the
rinsing solution has been removed.
14
Install in the reverse order
Coolant pump, coolant thermostat
Number
Designation
Engine
611.960/
961
Engine
611.962
Engine
612.961/
963
Engine
612.962/
967/990
BA20.10-P-1005-01A
Bolt of coolant thermostat housing to cylinder head
Nm
9999
Designation
Engine
613.960/
961
BA20.10-P-1005-01A
Bolt of coolant thermostat housing to cylinder head
Nm
9
Designation
Engine
628.960/961/962/
963
Copyright DaimlerChrysler AG 12.05.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorde
d by Modification services.
Page 2
Fig. 1: Disconnecting Negative Battery Cable
Courtesy of MERCEDES-BENZ OF NORTH AMERICA.
BASIC PROGRAMMING
1. Code radio. See Coding radio .
2. Set time on instrument cluster. Pull out knob at lowe r right of speedometer. To adjust hour, turn to right.
To adjust minute, turn to left.
3. If necessary, set time at stationary heater timer. See owner's manual.
4. Start engine and run at idle. Turn steering wheel fr om one lock position to the other to activate steering
angle sensor. Center steering wheel. Ma lfunction indicator lamp should go out.
5. If equipped, normalize ti lting/sliding roof. Open sunroof and hold down switch. Sunroof moves to end
position and pulls back 1/4 turn and stops. If equipped with lemella slidin
g roof, close roof and keep
2001 Mercedes-Benz ML320
2001-04 STARTING & CHARGING SYSTEMS Starters - 163 Chassis
me
Saturday, October 02, 2010 3:19:47 PMPage 3 © 2006 Mitchell Repair Information Company, LLC.
