1997 MAZDA MIATA bulb

DIAGNOSIS
SELF-DIAGNOSTIC SYSTEM
SAS unit will only display one code at a time. SAS unit will always display highest priority code first. After
repairing system, perform SYSTEM OPERATION CHECK
. If AIR BAG warning light is still flashing
during SYSTEM OPERATION CHECK, record code displayed. Repair system as necessary.
Retrieving & Clearing Codes
If codes are stored, AIR BAG warning light will flash or remain on when ignition is turned on. Codes are
automatically cleared when fault is corrected.
AIR BAG Warning Light Flashes
AIR BAG warning light indicates fault codes by flashing. Count the number of flashes between pauses to
determine code. See AIR BAG CODES
table. Codes are prioritized. If 2 or more faults are present, SAS unit
will display highest priority code first. After identifying code, go to appropriate code test.
AIR BAG Warning Light Remains On
Illumination of AIR BAG warning light continuously when ignition is turned on indicates a Code 0 (zero). See
AIR BAG CODES
table.
AIR BAG Warning Light Does Not Come On
Check for blown fuses, burned-out bulb, disconnected SAS unit, or open circuit between warning light and SAS
unit.
AIR BAG CODES
WARNING LIGHT DOES NOT COME ON WARNING:Follow air bag service precautions to prevent accidental air bag
deployment and personal injury. See SERVICE PRECAUTIONS
.
NOTE: If AIR BAG warning light does not come on and buzzer sounds when ignition is
turned on, check and repair warning light circuit first.
CodePossible Cause
0 (1) SAS unit
3Power Source Circuit
6Driver-Side Air Bag Module Circuit
7Passenger-Side Air Bag Module Circuit
(1)AIR BAG warning light remains on, indicating a Code 0.

1997 Mazda MX-5 Miata
AIR BAG RESTRAINT SYSTEM 1997 ACCESSORIES/SAFETY EQUIPMENT Mazda - Air Bag Restraint System
Microsoft
Sunday, July 05, 2009 1:40:47 PMPage 15 © 2005 Mitchell Repair Information Company, LLC.

between terminal AM of ABS CM harness connector and ground. If continuity exists, replace wiring
harness connector. If continuity does not exist, repair wiring harness.
7. Check ABS warning light bulb. Replace bulb as necessary. If bulb is okay, go to next step.
8. Check continuity between terminal AD of ABS CM harness connector and terminal 1K of instrument
cluster connector. See WIRING DIAGRAMS
. If continuity exists, check ABS warning light. See ABS
WARNING LIGHT under COMPONENT TESTING
. If continuity does not exist, repair wiring
harness.
ABS WARNING LIGHT REMAINS ILLUMINATED
1. Ensure battery is fully charged. Charge or replace as necessary. If battery is fully charged, go to next step.
2. Check ABS Control Module (ABS CM) connector for poor connection. Turn ignition on. Check if ABS
warning light goes out. If ABS warning light does not go out, go to next step. If ABS warning light goes
out, a temporary poor contact in wiring may have occurred and ABS is now functioning properly.
3. Turn ignition off. Disconnect ABS CM connector. See COMPONENT LOCATIONS
. Measure voltage
between terminals "A" and AB of ABS CM harness connector. See Fig. 3
. Also, measure voltage
between terminals "A" and AC of ABS CM harness connector, and between terminals "A" and AM of
ABS CM harness connector. If battery voltage is present, go to next step. If battery voltage is not present,
repair wiring harness.
4. Connect ABS CM connector. Check for ABS DTCs. See RETRIEVING DIAGNOSTIC TROUBLE
CODES under DIAGNOSIS & TESTING. If no DTCs are present, go to next step.
5. Turn ignition off. Disconnect ABS CM connector. Connect Harness Adapter (49-F066-022). Turn
ignition on. Check if ABS warning light goes out. If ABS warning light does not go out, repair short in
ABS warning light drive harness or instrument cluster. If ABS warning light goes out, replace ABS CM.
ABS WARNING LIGHT FLASHES WITH VEHICLE STOPPED
1. Ensure battery is fully charged. Charge or replace as necessary. If battery is fully charged, go to next step.
2. Check if a jumper wire is installed between terminals TBS and GND of Data Link Connector (DLC). See
Fig. 1
. If jumper wire is installed, remove jumper wire from DLC. If jumper wire is not installed, go to
next step.
3. Turn ignition off. Disconnect ABS Control Module (ABS CM) connector. See COMPONENT
LOCATIONS . Check continuity between terminal "P" of ABS CM harness connector and ground. See
Fig. 3
. If continuity exists, repair short to ground in DLC wiring harness. If continuity does not exist,
replace ABS CM. NOTE: ABS warning light will illuminate if voltage between terminal "A" (voltage
supply) of ABS CM harness connector and ground is less than about 10
volts.

1997 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1997 BRAKES Mazda - Anti-Lock
Microsoft
Sunday, July 05, 2009 1:48:48 PMPage 3 © 2005 Mitchell Repair Information Company, LLC.

Fig. 9: Locating Hydraulic Unit Valve Relay Connector Terminals
Courtesy of MAZDA MOTORS CORP.
ABS WARNING LIGHT
Operational Test
1. Start engine and observe ABS warning light. Light should illuminate for a few seconds. If light does not
illuminate as described, turn ignition off. Disconnect ABS control module connector. Using a jumper
wire, connect terminal AD of ABS control module connector to ground. See Fig. 3
. Turn ignition on.
2. If ABS warning light illuminates, check ABS control module. See ABS CONTROL MODULE. If light
does not illuminate, remove instrument cluster. Remove and check ABS warning light bulb. Replace bulb
as necessary. If bulb is okay, check METER fuse and wiring harness. Repair or replace as necessary. If
METER fuse and wiring harness are okay, go to next step.
3. Using ohmmeter, connect positive lead to terminal 2K (Black/Yellow wire) of instrument cluster and
negative lead to terminal 1K (Blue/Yellow wire) of instrument cluster. See Fig. 10
. If continuity is not
present, replace instrument cluster. If continuity is present, repair wiring harness between instrument
cluster and ABS control module.

1997 Mazda MX-5 Miata
ANTI-LOCK BRAKE SYSTEM 1997 BRAKES Mazda - Anti-Lock
Microsoft
Sunday, July 05, 2009 1:48:49 PMPage 16 © 2005 Mitchell Repair Information Company, LLC.

Fig. 3: Identifying Condenser Fan Relay Terminals
Courtesy of MAZDA MOTORS CORP.
CONDENSER FAN MOTOR
Disconnect condenser fan motor connector. Connect positive battery lead to condenser fan motor Black/Yellow
wire terminal, and ground Black wire terminal. Replace condenser fan motor if it does not operate.
EVAPORATOR THERMOSWITCH
1. Remove glove box. Operate engine at idle. Turn A/C off. Turn blower switch to 4th position (high) for a
few minutes to ensure evaporator temperature is greater than 32°F (0°C). Turn blower switch and engine
off.
2. Disconnect evaporator thermoswitch connector. Check continuity between thermoswitch terminals. If
continuity exists, go to next step. If there is no continuity, replace thermoswitch.
3. Submerge thermoswitch sensing bulb in ice cold water of less than 32°F (0°C). Ensure continuity does
not exist between thermoswitch terminals. Replace thermoswitch if continuity is not as specified.
PRESSURE SWITCH
1. Turn ignition off. Connect manifold pressure gauge set to system. If high-side pressure is 37-310 psi (2.6-
22.0 kg/cm
2 ), go to next step. If pressure is not as specified, check refrigerant level.
2. Disconnect pressure switch connector. Check continuity between switch terminals. If continuity exists,
pressure switch is okay. If there is no continuity, replace pressure switch.
REMOVAL & INSTALLATION

1997 Mazda MX-5 Miata
A/C-HEATER SYSTEM - MANUAL 1997 Manual A/C-Heater System
Microsoft
Sunday, July 05, 2009 1:41:48 PMPage 6 © 2005 Mitchell Repair Information Company, LLC.

HALOGEN BULBS
HEADLIGHT RETRACTOR
RADIATOR CAP
RADIATOR FAN
WARRANTY INFORMATION
BASIC NEW CAR WARRANTY
Basic components are warranted against defects in materials and workmanship for 36 months or 50,000 miles,
whichever occurs first. Tires are covered by a separate warranty offered by tire manufacturer.
ANTI-PERFORATION WARRANTY
Covers body sheet metal panels for 60 months, regardless of mileage, against perforation due to corrosion.
SAFETY RESTRAINT SYSTEM WARRANTY WARNING:Relieve fuel system pressure prior to servicing any fuel system
component (fuel injection models).
WARNING:Halogen bulbs contain pressurized gas which may explode if overheated.
DO NOT touch glass portion of bulb with bare hands. Eye protection
should be worn when handling or working around halogen bulbs.
CAUTION: If headlight retractor freezes during cold weather operation, DO NOT
attempt to force mechanism. Headlights should be kept raised at all times
in cold weather. To raise them, use only headlight retractor switch. DO
NOT use headlight switch.
CAUTION: Always disconnect the fan motor when working near the radiator fan. The
fan is temperature controlled and could start at any time even when the
ignition key is in the OFF position. DO NOT loosen or remove radiator cap
when cooling system is hot.
WARNING:Keep hands away from radiator fan. Fan is controlled by a thermostatic
switch which may come on or run for up to 15 minutes even after engine
is turned off.
CAUTION: Always refer to customer's copy of warranty information for specific
model application and/or coverage limitations.

1997 Mazda MX-5 Miata
MAINTENANCE INFORMATION 1997 MAINTENANCE Mazda Maintenance Information
Microsoft
Sunday, July 05, 2009 1:41:19 PMPage 7 © 2005 Mitchell Repair Information Company, LLC.