1997 Lexus ES300 steering

127
SECTION 3 ± 1
STARTING AND DRIVING
Starting and driving
Three±way catalytic converter 128
Engine exhaust caution 129
Before starting the engine 130
Ignition switch with steering lock 130
Parking brake 131
How to start the engine 132
Automatic transmission 133
Cruise control 140
Electronic modulated suspension 143
Traction control system 144
Brake system 145
Brake pad wear limit indicators 147
Types of tires 148

STARTING AND DRIVING
130
BEFORE STARTING THE ENGINE
1. Check the area around the vehicle before entering it.
2 Adjust seat position, seatback angle, head restraint
height and steering wheel angle.
3. Adjust inside and outside rear view mirrors.
4. Lock all doors.
5. Fasten seat belts.
Remember to check that the service reminder indicators
function when turning the key to ªONº, and check the fuel
gauge to see that you have sufficient fuel.
IGNITION SWITCH WITH STEERING
LOCK
ªSTARTº ± Starter motor on. The key will return to the
ªONº position when released.
For starting tips, see page 132.
ªONº ± Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the ªONº position if the
engine is not running. The battery will discharge
and the electronic ignition system/distributor
ignition system could be damaged.
ªACCº ± Accessories such as the radio operate, but the
engine is off.

STARTING AND DRIVING
131 If you leave the key in the ªACCº or ªLOCKº position and
open the driver's door, a buzzer will remind you to remove
the key.
ªLOCKº ± Engine is off and the steering wheel is locked.
The ignition key can be removed only at this position.
You must push in the key to turn it from ªACCº to the ªLOCKº
position. The selector lever must be put in the ªPº position
befoer turning the key in the ªLOCKº position.
When starting the engine, the key may seem stuck at the
ªLOCKº position. To free it, first be sure the key is pushed
all the way in, and then rock the steering wheel slightly while
turning the key gently.
If, in an emergency, you must turn the engine off while the
vehicle is moving, turn the key only to ªACCº.
PARKING BRAKE
To set: Hold the regular brake pedal down with your
right foot. Push down the parking brake pedal with your
left foot.
To release: Hold the regular brake down with your right
foot and push and parking brake pedal with your left
foot. When you lift your left foot, the parking barke
pedal will follow it to the released position.
Before leaving your vehicle, firmly apply the parking brake.
CAUTION!
Before driving, make sure the parking brake is fully
released and that the parking brake reminder light is
off.

STARTING AND DRIVING
146
Anti±lock brake system
The anti±lock brake system is designed to automatically
prevent lock±up of the wheels during a sudden brake or
braking on slippery road surfaces. This assists in
providing directional stability and steering performance
of the vehicle under these circumstances.
The anti±lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km/h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km/h (3 mph).
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle
is started. This means that the anti±lock brake system is in
the self check mode, and does not indicate a malfunction.
Effective way to press the ABS brake pedal: When the
anti±lock brake system function is in action, you may feel
the brake pedal pulsating and hear a noise. In this situa-
tion, to let the anti±lock brake system work for you, just
hold the brake pedal down more firmly. Do not pump the
brake. This will result in reduced braking performance.
The brake pedal pulsation caused by the anti±lock brake
system may indicate hazardous road surface conditions.
Although the anti±lock brake system assists in providing
vehicle control, it is still important to drive with all due care,
because the anti±lock brake system cannot overcome the
laws of physics that act on your vehicle:
Braking capability is dependent on tire friction with the road
surface.
Even though the anti±lock brake system is operating, a
driver cannot maintain full control on certain slippery road
surfaces, when cornering at high speeds, or in violent
maneuvers.
Avoid high speeds on wet roads. The anti±lock brake
system cannot eliminate the risk of hydroplaning and loss
of tire friction.
Always maintain a safe distance from the vehicle in front of
you. Compared with vehicles not fitted with an anti±lock
brake system, your vehicle may require a longer stopping
distance in the following cases:
Driving on rough, gravel or snow±covered roads.
Driving with tire chains installed.
Driving on roads where the road surface is pitted or has
other differences in surface height.