1997 Lexus ES300 lock

SWITCHES
16
HEADLIGHT SWITCH
To turn the lights on, twist the knob on the end of the
lever.
FIRST CLICKSTOP: Only the parking, tail, license plate,
side marker and instrument panel lights turn on.
SECOND CLICKSTOP: Headlights also turn on.
THIRD CLICKSTOP (ºAUTOº): The headlights and all other
lights automatically turn on depending on the darkness of the
surroundings.
Vehicles sold in U.S.A.: When the headlights are on, the
headlight indicator lights up in the instrument cluster.
Vehicles sold in Canada: When the tail lights are on, the
tail light indicator lights up in the instrument cluster.Manually twist the knob to the second clickstop to turn
on the headlights if they are needed immediately when
entering a dark tunnel, parking structure, etc.
When the headlight is turned to the first or second clickstop,
the brightness, of the instrument cluster will be reduced
slightly unless the instrument panel light control knob is
turned fully on.
The automatic light control sensor is on top of the driver's
side instrument panel.
Do not place anything on the instrument panel, and/or do not
affix anything on the windshield to block this sensor.
The lights automatically turn off when the driver's door is
opened with the ignition key turned to the ªACCº or ªLOCKº
position. To turn them on again, turn the ignition key to the
ªONº position, or turn the headlight switch off and then twist
the knob until the first or second clickstop. If you are going
to park for over one week, make sure the headlight switch
is off.

SWITCHES
19
WINDSHIELD WIPER AND WASHER
SWITCH

Interval adjuster Washer on
To turn the wipers on, move the lever down until you
reach the desired speed setting.
The ignition key must be in the ªONº position.
There are 3 settings:
ªINTº position: Intermittent operation
ªLOº position: Low speed operation
ªHIº position: High speed operation
Twist the interval adjuster upward to increase the
wiping time interval between sweeps, and downward to
decrease it.
The wiper lever must be in the ªINTº position.To make the washer squirt, push the button on the end
of the lever.
Also, the wipers will automatically operate a couple of times
after the washer squirts even with the lever in the ªOFFº
position.
The low washer fluid warning light in the instrument cluster
comes on when the fluid level in the tank becomes nearly
empty. For information on adding washer fluid, see ªAdding
washer fluidº on page 230.
In cold weather, warm the windshield with the defroster
before using the washer. This will help prevent icing, which
could block your vision.NOTICE
Do not operate the wipers if the windshield is dry. It
may scratch the glass.

SWITCHES
22
CAUTION!
Since the mirror surfaces high temperatures, keep
your hands off them when the switch is on.
If further defrosting or defogging is desired, simply actuate
the switch again. When the surface has cleared, push the
switch once again to turn the defogger off. Continuous use
may cause the battery to discharge, especially during
stop±and±go driving. The defogger is not designed to dry
rain water or to melt snow.
If the outside rear view mirrors are heavily coated with ice,
use a spray de±icer before operating the switch.
NOTICE
When cleaning the inside of the rear window, be
careful not to scratch or damage the heater wires.
To prevent the battery from being discharged, do
not operate the defogger continuously longer
than necessary.
POWER WINDOW SWITCHES

For driver's window
For front passenger's window
For left rear window
For right rear window
To raise or lower the windows, use the switch on each
door. The passengers' windows can also be controlled
by the switches on the driver's door.
The ignition key must be in the ªONº position. However, even
if the ignition key is turned to the ªACCº or ªLOCKº position,
the window can be operated until any of the doors is opened
(or for about 45 seconds).

SWITCHES
23
Operating the driver's switch
To lower the window, push the switch halfway down.
Pull it up to raise the window. The window glass moves
as long as the switch is operated.
To fully lower the driver's window automatically, push
the switch fully down.
In automatic operation, the window will fully open even if you
leg go of the switch. To stop the window partway, lightly pull
the switch up and then release it.
Operating the passenger's switches
To lower the window, push the switch down. Pull it up
to raise the window. The window moves as long as the
switch is operated.
Operating the window lock switch
Indicator light
With the window lock switch pressed in, only the
driver 's window can be raised or lowered.
The indicator lights on the switch tell you which of the
switches can be operated.

SWITCHES
24
CAUTION!
To avoid serious personal injury, you must do the
following.
Always make sure the head, hands and other
parts of the body of all occupants are kept
completely inside the vehicle before you close the
power windows. If someone's ncek, head or
hands gets caught in a closing window, it could
result in a serious injury. When anyone closes the
power windows, be sure that they operate the
windows safely.
When small children are in the vehicle, never let
them use the power window switches without
supervision. Use the window lock switch to
prevent them from making unexpected use of the
switches.
Never leave small children alone in the vehicle,
especially with the ignition key still inserted. They
could use the power window switches and get
trapped in a window. Unattended children can
become involved in serious accidents.
EMERGENCY FLASHER SWITCH
To turn on the emergency flashers, push the switch.
All the turn signal lights will flash. The emergency flashers
will work with the engine running or off and with or without the
ignition key.
Turn on the emergency flashers to warn other drivers if you
must stop your vehicle where it might be a traffic hazard.
Always pull your vehicle as far off the road as possible.
The turn signal light switch will not work when the emergency
flashers are in operation.
NOTICE
To prevent the battery from being discharged, do
not leave the switch on longer than necessary when
the engine is not running.