1997 HONDA CR-V passenger

Ftom page24-54
Check for 6 short power in the cable r6el {cont'd):5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-28).7. Read the DTC (see page 24-261.
b DTC 1-4 indicarodz
YESNO
Short to power in lhe cablo roel; replace th€ cabl€ ieel{see pago 24-91).
Check tor a short to power in th. SRS main harn$s:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnect the front passenger's airbag connector {anddisconnect both seat belt tensioner connectors).3. Rernove the special tool (2 O) from the SRS main harness2P connector.4. Disconnect the SRS main harness 18P connector fromthe SRS unit.5. Beconnect the batterv positive cable, then reconnect thenegative cable.6. Connect a voltmeter between the No. 1 {+) terminal olthe SRS main harness 18P connector and body ground.7. Turn the ignition switch ON (ll), and measure voltage.There should be 0.5 V or less.8. Turn the ignition switch OFF.9. Connect a voitmeter between the No. 13 {+i terminal ofthe SRS main harness 18P connector and body ground.10.Turn the ignition switch ON lll), and measure voltage.There should be 0.5 V or less.
Are voltages as specified?
YESNO
Faulty SRS unit; replaco th€ SRS unit lsoo pas6 24-95).
Short to power in th€ SRS main hamoss; roplece the SRSmain haanass.
SRS MAIN HARNESS18P CONNECTOR
24-55
www.emanualpro.com

)
SRS MAIN HARNESS18P CONNECTOR
)
From page 24 56
Check{or a short to ground in the cable reel (cont'd):
5. Reconnect the batterv positive cable, then reconnect thenegative cable.6. Erase lhe DTC memoty lsee page 24-28).7. Read the DTC lsee page 24 26).
ls OTC 1-5 indicated?
YESNO
Short lo ground in the cable reel; replace the cable reel{see oaoe 2,1-91}.
Check for a short to ground in the SRS main harness:'1. Disconnect the battery negative cable, the disconnect thepositive cable, and wait for three minutes.2. Disconnect the tront passenger's airbag 2P connector(6nd disconnect both seat belt tensioner connectors).3. Remove the special tool 12 {))from the SRS main harness2P connector.4- Disconnect the SRS main harness 18P connector fromthe sRs unit.5. Check resistance between the No. l terminal o{theSRSmain harness 18P connector and ground, and betweenthe No. 13 terminal of the SRS main harness 18P connec-tor and ground.There should be I M0 or more.
ls lhe resistance as soecitiod?
NOYES
Faulw SRS unit reDlace the SRS unit lsee paqe 24-951.
Short to ground in the SRS main harness; replace the SRSmain ham€ss,
24-57
www.emanualpro.com

Troubleshooting
DTC 2-1 and DTC 2-2
CAUTION: Whenever the ignition switch is ON lll), or
has been turned OFF tor less than throe minutes, be
careful not to bump the SRS unit; the airbags could
accidentally deploy and cause damage or iniuries.
SRS MAIN HARNESS
SIMULATORI-EAD C
!a
07TAZ - SZ5tt11Aand SRS INFLATOR
/StMULATOR/ Q A JACKI
y' 07slz-TA411A
ffi
Try to reproduce the SRS indicator light:1. Erase the DTC memory (see page 24-28).2. Turn the ignition switch ON (ll), and check that the SRSindacator light comes on for about sax seconds and then
Does the SRS indicator lioht stav on?
Intermittent tailure, svstem is OK ai lhis time. SeeTroubl*hooting Intermittent Failures on paqe 24-28.
Chock for an open in the passongor's airbag inflator:1. Turn the ignition switch OFF.2. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.3- Disconnect the front passenger's airbag connector lromthe SRS main harness (see page 24-2:,,.4. Connect the special tool (2 0) to the SRS main harness2P connector. Do not disconnect the driver's airbag con,nector.5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-28).7. Read the DTC (see page 24 26!'.
ls DTC 2-1 or DTC 2-2 indicated?
Open or incrcased resistance in tho passenger's airbag
To page 24'59
24-58
--
www.emanualpro.com

Troubleshooting
DTC 2-3
CAUTION: Whenevor the ignition switch is ON { }, orhas been turned OFF for less than three minutes, becareful not to bump the SRS unit; lhe airbags couldaccidentally deploy and causo damage or iniuries.
{J
SIMULATORLEAD C07TAZ - SZ50I1Aand SRS INFLATOR
/STMULATOR/ I2n JACKI
y' 07sAz -fB1011A
ffi
SRS MAIN HARNESS
Try to reproduce the SRS indicator light:1- Erase the DTC memory {see page 24 28).2. Turn the ignition switch ON (ll), and check that the SRSindicator light comes on for about six seconds and thengoes off.
Does the SRS indicator light stay on?
YESNO
Intermittont failur€, syslem is OK at this time. 560T.oubloshooting lntormittent Failur6 on page 24-28.
Check for a short to another wiro or decreased resbtanc€ inthe pa$€nger's airbag inflator:1. Turn the ignition switch OFF.2. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.3. Disconnect the front passenger's airbag 2P connectorfrom the SRS main harness (see page 24-23).4. Connect the special tool (2 O) to the SRS main harness2P connector. Do not disconnect the driver,s airbag con-nector.5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24 28i.7. Read the DTC (see page 24-26).
ls DTC 2-3 indicated?
NOYES
Short to another wir6 or decaea3€d r€aktance in the oas-senger's airbag intlatoi; replac€ the passenger's airbag{see pago 24-8t1.
To page 24 61
24-60
,-
www.emanualpro.com

Troubleshooting
DTC2-4
GAUTION: Wh€never tho ignition switch is ON 0t). orhas been turned OFF for less than threo minutes, bocareful not to bump the SRS unit; the airbags couldaccidentally deploy and cause damaga or iniuriss.
SRS MAIN HARNESS
SIMULAYORLEAD C
Ot-
07TAZ - SZ5011A.nd SRS INFLATOR
/stMU|_ATOR/ t2 tr JAoKI
// olsAz-Tsn11A
ffi
Try to reproduce the SRS indicator light:1. Erase the DTC memory (see page 24-28i.2. Turn the ignition switch ON (lli, and check that the SRSindicator light comes on tor about six seconds and thengoes off.
Do€s the SRS indicator light stay on?
YESNO
Inlermittent tailure, system is OK at this tim€. SceTroubleshooting Intermitt€.f Failures on page 2+28.
Check for a short to power in the passengar,s ai.bag infla-tor:1. Turn the ignition switch OFF.2. Disconnect the baftery negative cable, then disconnectthe positive cable, and wait for three minutes.3. Disconnect the front passenger's airbag 2P connectorIrom the SRS main harness lsee page 24-23).4. Connect the special tool (2 O) to the SRS main harness2P connector. Do not disconnect the driver,s airbag con,nector,5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-28).7. Read the DTC (see page 24-26|'.
ls DTC 2-4 indicsted?
YESNO
Sho.t power in the passenger's airbag infator; rsplece thopaisonge/i airbag {s€e pag€ 2il-89).
To page 24-63
24-62
--
www.emanualpro.com

Troubleshooting
DTC 2-5
CAUTION: Whenever the igniiion switch is ON {ll}, orhas be€n turn€d OFF for less than three minutes, becareful nol to bump the SRS unit; the sirbags couldaccidentally doploy and causo damage or iniuries.
tl
SIMULATORLEAO C07TAZ - SZ5011A.nd SRS INFLATOR
/StMULATOR/ t2 a JACKI
/ 07saz-fB&11^
ffi
Try to rep.oduce the SRS indicstor tight:1. Erase the DTC memory (see page 24-28).2. Turn the ignition switch ON 0l), and check that the SRSindicator light comes on for about six seconds and thengoes off.
ooes th6 SRS indicaror light st.y on?
YESNO
Inte.mitt.nt failure, system is OK at thi3 time. S€eTroubl6hooting Intermittem Failur6 on page 2+28.
Check for a short to gaound in th6 prsenger,i airbag inlla-tor:1. Turn the ignition switch OFF.2. Disconnect the battery nogative cable, then disconnectthe positive cable, and wait for three minutes.3. Disconnect the front passenger,s airbag 2p connectorfrom the SRS main harness {see page 24-23).4. Connect the special tool (2 0) to the SRS main harness2P connector. Do not disconnect the driver,s airbag con,nector.5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-28).7. Read the DTC lsee page 2[-261.
ls DTC 2-5 indicated?
YESNO
Short to ground in the pas€ngert airbeg inflator; ,cplacethe passenge/s airbag (s€e page 2+991.
To page 24 65
24-64
--
www.emanualpro.com

Troubleshooting
DTC 3-1 and DTC 3-2
CAUTION: Whenever the ignition switch is ON flll, orhas been turned OFF for less than three minutes, b€careful not to bump th€ SRS unit; the airbags couldaccidenlally deploy and cause damage or iniuries.
DRIVER'SSEAT BELT TENSIONERLEFT SIOE WIREHARNESS2P CONNECTOR2P CONNECTOR
-
\
SRS SIMULALEAD C07TAZ - SZ501rAand SRS INFLATORSTMULAToR It2 0JACKI IoTsaz - TB4ot lA t
24-66
Try to reproduce the SRS indicatoi light:1. Erase the DTC memory (see page 24-29).2. Turn the ignition switch ON 1 ), and check that the SRSindicator light comes on for about six seconds and thengoes off.
Does the SRS indicaior lighr stay on?
YESNO
Intermittent failure, system is OK at this time. SeeTroubleshooting lfiermittent Failu.6s on page 24-28.
Check tor an open in the driver's seat b6lt tensioner:1. Disconnect the negative battery cable, and wait lor threeminutes.2. Disconnect the drave/s seat belt tensioner 2p connectorfrom the left side wire harness 2P connector (see page24-23). Do not disconnect the lront passenger,s seat belttensioner 2P connector.3. Connect the special tool {2 O) to the left side wire harness2P connector,4. Reconnect the negative baftery cable5. Erase the DTC memory {see page 24,28).6. Read the DTC (see page 24-26).
ls OTC 3-1or DTC 3-2 indicatedT
YESNO
Open or increased resistance in the d.iver's seat belt ten-sioner; replace the driver's seat belt {see page 2il-91).
To page 24 67
www.emanualpro.com

)
LEFT SIDE WIREHARNESS2P CONNECTOR
SRS MAINHARNESS2P CONNECTOR
C
00
SRS SIMULATORLEAD C07TAZ - SZ5011Aand SRS INFLATOR
{2 0 JACKI07sAz - T84011A
art)
sRsUNIT
SRS MAIN HARNESS.I8P CONNECTOR
)
From page 24-66
Check for an oFn in thc aide wir6 harne$:1. Disconnect the left side wire harness 2P connector fromthe SRS main harness 2P connector.2. Connect the special tool (2 o) to the SRS main harness2P connector.3. Erase the DTC memory.4. Read the DTC.
ls DTC 3-l or DTC 3-2 indicated?
YESNO
Ooen or incrers€d reeidance in the lelt side wire hame3s;r€Dlaca the hamess.
Check for an open in the SRS main harness:1. Disconnect the negative battery cable, and wait for threeminutes.2. Disconnect the driver's and front passenger's airbags,and front passenger's seat belt tensioner connectors (see
page 24-231.3. Disconnect the SRS main harness 18P connector from
the SRS unit. Do not disconnect the special tool (2 O)from the SRS main harness 2P connector.4. Check resistance between the No. 4 and No. 11 terminalsof the SRS main harness 18P connector. There should be2.0 - 3.0 0.
13lhe resistance as soecified?
NOYES
Faulty SFS unil or poor contad at the SRS main h.m€ss18P connector and th€ SRS unit. check the connectionbetween the SRS main harn$s 18P connector and theSRS unit. lf the connector i3 OK. r€Dlaco ihe SRS unit(s66 pas6 24-951.
ODen or incaoased resistance in the SRS msin harness;reolace the SRS main harn€ss.
terminals
24-67
www.emanualpro.com