1997 GMC JIMMY wiper blades

Windshield Wipers
You control the windshield
wipers
by turning the band
with the wiper symbol
on it.
For a single wiping cycle. turn the band to MIST. Hold
it there until the wipers start. then let go. The wipers will
stop after one wipe. If you want Inore wipes, hold the
band on
MIST longer.
You can set the wiper speed I‘or a long or short delay
between wipes. This can be very
LIS~~LII in light rain or
snow. Turn the band to choose the delay time. The
closer to
LOW, the shorter the delay.
Be sure to ciear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them.
If your blades do become
worn or datnaged.
set new blades or blade inserts.
Windshield Washer
At the top of the multifunction lever there’s a paddle
marked with the windshield washer
symbol and PUSH.
To spray washer fluid on the windshield, press the
paddle. The wipers
will clear the window and then
either stop or return to your preset speed.
I
I
A C iTJTION:
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can
form ice an the windshield, blocking
your vision.
2-40

The heavier the rain. the harder it is to see. Even il'yo~~r
windshield wiper blades are
in good sl~ape. a heavy rain
can make it harder to see road signs and traffic signals.
pavement markings, the edge
of the road and even
people walking.
It's wise
to keep your wiping equipment in good shape
and keep your windshield washer tank filled with
washer fluid. Replace your windshield wiper inserts
when they show signs
of streaking or missing areas on Wet brakes can cause accidents. They won't work
the windshield. or when strips of rubber start to separatc as well in a quick stop and may cause pulling to
from the inserts. one side. You could lose control of the vehicle.
After driving through a large puddle
of water or
a car wash, apply your brake pedal lightly until
your brakes work nornlally.
4-30

Front Reading Lamps
1.
2.
3.
4.
5.
6.
7.
a.
Use a coin or srnall screwdriver to 11nscrew the
center
of the overhead console lamp lens while
pressing
in on the lamp assembly.
Remove the lamp assembly from the console.
Remove the bulb assembly from the lamp assembly.
Pull the bulb straight out
of the base.
Put a new bulb into the bulb base.
Install the bulb assembly into t.he lamp assembly.
Place the lamp assembly
into the console, turning it
to latch it in place.
Install
the lens.
Vanity Mirror Lamps
4. Press the new bulb into place.
5. Slide the side tabs of the lens under the side of the
vanity assembly frame.
6. Rotate the lens downward.
7. Snap the lens into the frame.
Windshield Wiper Blade Replacement
See ”Normal Maintenance Replacement Parts” in the
Index for the proper type
of replacement blade.
NOTICE:
~~~~
Use care when removing or installing a blade
assembly. Accidental bumping can cause the
arm
to fall back and strike the windshield.
1. Insert the blade of a small screwdriver into the center I I
slot at the bottom of the lens.
2. Gently pry the screwdriver down in order to lift out
the lens.
3. Pry out the bulb.
1. To remove the old wiper blades, lift the wiper arm
until it locks into a vertical position.
6-38

Cleaning Glass Surfaces
Glass should be cleaned often. GM Glass Cleaner (GM
Part
No. 1050427) or a liquid household glass cleaner
will remove normal tobacco smoke and dust films on
interior glass.
Don't use abrasive cleaners on glass. because they may
cause scratches. Avoid placing decals on
the inside rear
window, since they may have to be scraped off later.
If
abrasive cleaners are used on the inside of the rear
window, an electric defogger element may be damaged.
Any temporary license should not be attached across the
defogger grid.
Cleaning the Outside of the
Windshield, Backglass and
Wiper Blades
If the windshield is not clear after using the windshield
washer, or
if the wiper blade chatters when running.
wax, sap or other material may be on the blade
or windshield. Clean the outside
of the windshield with GM
Windshield
Cleaner, Bon Ami@ Powder (non-scratching
windshield is clean
if beads do not form when you rinse
it with water.
c' olass cleaning powder), GM Part No. 10500 1 1. The
Grime
from the windshield will stick to the wiper blades
and affect their performance. Clean the blade by wiping
vigorously
with a cloth soaked in full-strength
windshield washer solvent. Then rinse the blade
with water.
Check the wiper blades and clean them as necessary;
replace b1ade.s that look worn.
Weatherstrips
Silicone grease on weatherstrips will make them last
longer? seal better. and not stick or squeak. Apply
silicone grease
with a clean cloth at least every six
months.
During very cold, damp weather nIo1-e frequent
application may be required.
(See "Recommended
Fluids and Lubricants"
in the Index.)
6-53

At Least Twice a Year Automatic Transmission Check
Check the transmission fluid level: add if needed. See
"Automatic Transmission"
in the Index. A fluid loss
may indicate
a problem. Check the system and repair
if needed.
Restraint System Check
Make sure the safety belt reminder light and all your
belts. buckles, latch plates, retractors and anchorages are
working properly. Look
for any other loose or damaged
safety belt system parts.
If you see anything that might
keep
a safety belt system from doing its .job, have it
repaired. Have any torn or frayed safety belts replaced.
Also
look. for any c.)pened or broken air bag covers, and
have them repaired or replaced. (The air
bag system
does not need regular maintenance.)
Wiper Blade Check
Inspect wiper blades for ~vear or cracking. Replace blade
inserts that appear worn or damaged or that streak or
miss areas of the windshield.
Also see "Wiper Blades.
Cleaning"
in the Index.
Manual Transmission Check
Check the transmission fluid level; add if needed. See
"Manual Transmission"
in the Index. Check for leaks.
A fluid loss ITI~~ indicate a problem. Have the system
inspected and repaired
if needed.
Hydraulic Clutch System Check
Check the fluid level in the clutch reservoir. See
"Hydraulic Clutch Fluid" in the Index. A fluid loss in
this system could indicate a problem. Have the system
inspected and repaired at once.
At Least Once a Year
Key Lock Cylinders Service
Lubricate the key lock cylinders with the lubricant
specified
in Part D.
Body Lubrication Service
Lubricate all body door and fuel door hinges, rear
compartment hinges, latches and locks including the
moving seat hardware. Lubricate the hood safety lever
pivot and prop rod pivot. Part
D tells you what to use.
More frequent lubrication
may be required when
exposed to a corrosive environment.
t (rlove box, console doors and the body hood and any
7-47