1997 GMC JIMMY start stop button

Key Release Button
The key cannot be removed
from the ignition of 111anual
transmission vehicles
l~nless the
key release
button
is used.
To re~~xwe the key on manual transmission vehicles.
t111-n the key to the OFF position. Then turn the key to
the LOCK position while pressing the key release button
down
at the same tinle. Pull the key straight out.
On automatic transmission \:chicles, turn the key
to
LOCK and pdl it straight out.
Starting Your Engine
Automatic Transmission
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any otl~er position -- that's a
safety feature. To restart when you're 1111-cl:;~ciy moving,
use NEUTRAL
(N) only.
NOTICE:
Don't try to shift to PARK (P) if' your vehicle
is moving.
If you do, you could damage the
transmission. Shift to PARK (P) only when
your vehicle is stopped.
2-15

E11~~11-e the shift lever is f~~lly in PARK (P) range before
starting
the engine. Your vehicle has a brake-transmission
shift interlock. You have to
fully apply your regular brakes
before
you can shift from PARK (P) when the ignition
key is
in the RUN position. If you cannot shift out of
PARK (P), ease pressure on the shift lever -- push the shift
lever all
the way into PARK (P) (press the button in on the
console shift lever)
as you maintain brake application.
Then n~ove the
shift lever into the gear you wish. See
“Shifting Out of PARK
(P)“ in the Index.
REVERSE (R): Use
this gear to back up.
NOTICE:
Shifting to REVERSE (R) while your vehicle
is moving forward could damage your
transmission. Shift
to REVERSE (R) only
after your vehicle
is stopped.
To rock yo~~r vehicle back and forth to get out of snow.
ice or
sand without damaging your transmission, see
”Stuck:
In Sand, Mud. Ice or Snow“ in the Index. NEUTRAL
(N): In this position, your engine doesn’t
connect
with the wheels. To restart when you’re already
moving. use NEUTRAL
(N) only.
Shifting out of PARK
(P) or NEUTRAL (N) while
your engine is “racing” (running at high speed)
is
dangerous. Unless your foot is firmly on the
brake pedal, your vehicle could move very
rapidly. You could lose control and hit people or
ob-jects. Don’t shift out of PARK
(P) or
NEUTRAL (N) while your engine is racing.
I NOTICE:
Damage to your transmission caused by shifting
out of PARK
(P) or NEUTRAL (N) with the
engine racing isn’t covered by your warranty.
2-19

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
( I ) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Programming the Transmitter
Do not LIS~ the transmitter with any garage door opener
that does not have the ”stop and reverse’‘ feature. This
includes any garage door opener model manufactured
before April
1, 1982.
Re .WI-P tllcrt pwplt~ cml ohjucts c11-0 clmr of‘the g(it-cqe
cloo~. Jolr citxl I?t-~.’s”L“ll}”ill,s!
Your vehicle’s engine should be turned off while
programming the transmitter. Follow these steps to
program
up to three channels:
I, If you have not previously programmed a universal
channel, proceed to Step
2. Otherwise, hold down the
two outside buttons on the universal transmitter
until
the red light begins to flash rapidly (approximately
20 seconds). Then rekase the buttons. This procedure
initializes the memory and erases any previous
settings for all three channels.
2. Hold the end of the hand-held transmitter against the
bottom surface of the ~~niversal transmitter
so that
you can still see the red
light.
3. Decide which one of the three channels you want to
program. Using both hands, press the hand-held
transmitter button and the desired button on the
universal transmitter. Continue
to hold both buttons
through Step
4.
4.
Hold down both buttons until yo~r see the red light
on the Llniversal transmitter flash rapidly. The rapid
flashing, which could take up
to 90 seconds,
indicates that the universal transmitter has been
programmed. Release both buttons once the light
starts
to flash rapidly.
If you have trouble programming the universal
transmitter, make s~rre that you have followed the
directions exactly
as described and that the battery in the
hand-held transmitter is not dead.
If yo~t still cannot
program
it, rotate the hand-held transmitter end over end
and
try again. The universal transmitter may not work
with older garage door openers that do not meet current
Federal Consumer Safety Standards.
If you cannot
program the transmitter after repeated attempts. consult
your
GM dealer.
Be sure to keep the original hand-held transmitter in case
you need
to erase and reprogram the universal transmitter.
2-65

CD AUX: To switch between the player and the radio
when a disc is playing, press the
AM-FM button. To
return to the player, press CD AUX. When a disc is
playing, the letters CD and the
CD symbol will appear
on the display. (If the radio is turned off, the disc stays
in the player and will resume playing at the point where
it stopped.)
EJECT: Press this button to eject the disc from the
player and play the radio.
When the same or a new disc
is inserted, the disc will
start playing on track one. If a compact disc is left
sitting in the opening for more than a few seconds,
the
player will pull the CD back in. The radio will continue
playing. When the ignition is
off, press this button to
load a
CD. If you leave a compact disc in the player
while listening to the radio, it may become warm.
Theft-Deterrent Feature
THEFTLOCK" is designed to discourage theft of your
radio. It works by using a secret code to disable all radio
functions whenever battery power is removed.
The THEFTLOCK feature for the radio may be used or
ignored.
If ignored, the system plays normally and the
radio is not protected by the feature. If THEFTLOCK
is
activated, your radio will not operate if stolen.
When
THEFTLOCK is activated, the radio will display
LOC to indicate a locked condition anytime battery
power is removed. If your battery loses power for any
reason, you must unlock the radio with the secret code
before it will operate.
Activating the Theft-Deterrent Feature
The instructions which follow explain how to enter your
secret code to activate the THEFTLOCK system. It is
recommended that
you read through all nine steps
before starting the procedure.
NOTE: If you allow more than
15 seconds to elapse
between any steps, the radio automatically reverts to
time and you must start the procedure over at Step
4.
3-17