1997 FORD THUNDERBIRD clock

228 %
*
[MC30300( ALL)03/96]
3. Replace the fuel cap completely when you
are finished. Turn it clockwise 1/4 turn until
it is tight. It will click when it is fully
tightened.
*
[MC30400( ALL)01/96]
4. Push the fuel door closed.
%*
[MC30500( ALL)01/96]
RWARNING
If you do not use the proper fuel cap, the
pressure in the fuel tank can damage the
fuel system or cause it to work improperly
in a collision.
*
[MC30600( ALL)01/96]
NOTE: If you replace your fuel cap with an
aftermarket fuel filler cap, the customer
warranty may be void for any damage
to the fuel tank and/or fuel system.
%*
[MC30700( ALL)01/96]
Choosing the Right Fuel
*
[MC30801( ALL)03/96]
Use only UNLEADED FUEL. The use of leaded
fuel is prohibited by law and could damage
your vehicle. The damage may not be covered
by your warranty.
*
[MC30901( ALL)04/96]
Your vehicle was not designed to use fuel
containing manganese-based additives such as
MMT. Additionally, vehicles certified to
California emission standards (indicated on the
underhood Vehicle Emissions Control
Information label) are designed to operate on
California reformulated gasolines. If California
reformulated gasoline is not available when you
refuel, your vehicle can be operated on
non-California fuels. However, even though your
engine will perform adequately on other
gasolines, the performance of the emission
control devices and systems may be adversely
affected. Repair of damage caused by using a
fuel that your vehicle was not designed for may
not be covered by your warranty.
File:11rcmcb.ex
Update:Thu May 30 11:02:59 1996

239
*
[MC44800( ALL)03/96]
Installing the headlamp bulb
*
[MC45000(MBC )01/96]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[MC45200(MBC )01/96]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstop.º
*
[MC45300( ALL)01/96]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[MC45400(MBC )01/96]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
%*
[MC45700( BCGV)01/96]
High-Mount Brakelamp Bulbs
[MC45800( BCGV)12/95]
Your vehicle has a brakelamp mounted in the
rear window, called a high-mount brakelamp.
You may need to remove this lamp at times to
replace the brakelamp bulb or to clean the rear
window.
File:11rcmcb.ex
Update:Thu May 30 11:02:59 1996

240 [MC45900( B )12/95]
half page art:0010434-AParts of the high-mount brakelamp
% [MC46200( BCGV)12/95]
Toremovethe high-mount brakelamp:
[MC46300( BC )12/95]
1. Slide the trim cover toward the front of the
vehicle to disengage the retaining clips.
[MC46500( BC )12/95]
2. Twist the socket counterclockwise and
remove from lamp.
[MC46800( BC )12/95]
3. Pull bulb out of socket.
[MC47000( BC )12/95]
4. Remove the retaining screw.
[MC47100( BC )12/95]
5. Lift the lamp above the carpet and slide
away from the rear window.
[MC47300( BC )12/95]
6. Replace the burned out bulbs.
File:11rcmcb.ex
Update:Thu May 30 11:02:59 1996

241
*
[MC47400( BCGV)01/96]
Toinstallthe high-mount brakelamp:
[MC47500( BC )12/95]
1. Slide the lamp into slots, toward the rear
window.
[MC47700( BC )12/95]
2. Install the screw.
[MC47900( BC )12/95]
3. Push bulb into the socket.
[MC48000( BC )12/95]
4. Install the bulb and socket into the lamp and
twist socket clockwise until it locks.
[MC48100( BC )12/95]
5. Slide the trim cover toward rear of vehicle
to engage the retaining clips.
File:11rcmcb.ex
Update:Thu May 30 11:02:59 1996

Index 291
Cleaning your vehicle (continued)
mirrors................ 89
plastic parts............. 244
polishing............... 243
rustproofing............. 243
safety belts.............. 244
tail lamps.............. 244
upholstery and interior trim...... 245
washing............... 243
waxing............... 243
wheels................ 246
Climate control system.......... 59
air conditioning.......... 59,62
heating.............. 59,62
Clock.................. 71
Cold engine starting........... 140
Combination lap and shoulder belts . . . 105
Compact disc player (see Electronic
sound system)............. 26
Compact disc radio (see Electronic sound
system)................ 26
Console, description............ 91
Controls
mirrors................ 86
power seat.............. 102
Coolant (see Engine coolant)....... 207
checking and adding......... 207
drain and flush............ 211
preparing for storage......... 251
proper solution............ 209
refill capacities............ 248
specifications............. 249
temperature gauge........... 21
warnings............... 207
File:rcixb.ex
Update:Thu May 30 11:06:50 1996