1997 FORD RANGER ECO mode

176
[GF16190(R)05/96]
Four-wheel drive operation (4x4 HIGH or 4x4 LOW) on dry
pavement is not recommended. Operating the vehicle in
four-wheel drive on dry pavement will increase noise, vibration,
tire wear, decrease fuel economy, and make four-wheel drive
disengagement difficult for the transfer case.
[GF16200(R)05/96]
Electric shift system indicator lights
[GF16210(R)05/96]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[GF16220(R)05/96]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[GF16230(R)05/96]
n
4WD High Ð Only the 4WD light is lit.
[GF16240(R)05/96]
n
4WD LOW mode Ð Both the 4WD and 4WD LOW lights
are lit.
[GF16250(R)05/96]
To shift from Two-Wheel Drive to 4WD High:
[GF16260(R)05/96]
To shift into 4WD High rotate the 4WD switch located on the
instrument panel to 4x4 High. This shift can be done at a stop
or at speeds up to 55 miles per hour (88 km/h). When the
vehicle is driven, the automatic locking hubs will engage. If the
vehicle is stopped while in 4WD and the vehicle direction is
reversed from the previous direction, the automatic locking hubs
will momentarily disengage and re-engage. The automatic
locking hubs may click as they automatically engage in the new
direction.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

Driving
179
[GF16400(R)05/96]
To shift from 4x4 LOW to 4x4 HIGH or 2WD:
[GF16410(R)05/96]
Stop the vehicle, depress the brake and place the automatic
transmission into N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4x4 HIGH or 2WD.
[GF16420(R)05/96]
It is not recommended to operate the vehicle in the 4WD modes
with a temporary spare. If 4WD operation is necessary, do not
operate at speeds above 10 mph or for distances above 50 miles.
Extended operation in 4WD with a temporary spare may result
in damage to drivetrain components.
%*
[GF17000(R)05/96]
4x4 Systems Ð Lever Operated
*
[GF17010(R)05/96]
The lever operated transfer case can be placed into four
positions. The 2H position is the two-wheel drive position in
which power is delivered only to the rear axle. The 4H position
provides four-wheel drive with power delivered to the front
and rear axles for increased traction. The 4L position provides
four-wheel drive with power delivered to the front and rear
axles when the above average power is required at reduced
speeds. In the N (neutral) position, there is no power delivered
to either axle.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

Maintenance and Care
297
%*
[MC42450(R)01/96]
Information about your vehicle's emission control system is on
the Vehicle Emission Control Information decal located on or
near the engine. This decal identifies engine displacement and
gives some tune-up specifications.
%*
[MC42460(R)03/96]
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
*
[MC42470(R)04/96]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If your check engine light is on, reference the
check engine light description under theWarning Lights and
Gaugessection. Your vehicle may not pass an I/M test with the
check engine light on. If the vehicle's powertrain system or its
battery has just been serviced, the OBD II system is reset to a
not ready for I/M testing condition. To prepare for I/M testing,
additional city and highway driving is necessary to complete the
check of the OBD II system.
*
[MC43000(R)05/96]
The driving modes required to reach the ready condition consist
of a minimum of 30 minutes of city and highway driving as
described below:
[MC43100(R)03/96]
n
20 minutes of driving in stop and go city-type traffic with at
least four (4) idle periods.
*
[MC43200(R)03/96]
n
10 minutes of driving on an expressway or highway
[MC43300(R)03/96]
Before completing the above driving modes, the engine must be
warmed up and operating temperature. Once started, the vehicle
must not be turned off during the above driving modes. If the
vehicle owner is unable to meet the I/M requirements by using
these driving patterns, an authorized service center can perform
a detailed OBD II Drive Cycle as it would any other type of
repair work.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997