1997 FORD RANGER lights

Controls and Features
95
*
[CF80212(R)05/96]
When you use the remote entry UNLOCK or PANIC controls,
the illuminated entry system turns on the vehicle's interior
lights for 25 seconds. You can turn these lights off with the
remote entry LOCK control or by turning the ignition to the
ON or ACCESSORY position.
[CF80214(R)01/96]
7-1/2 pica art:0021160-A% [CF80300(R)04/96]
Arming and Disarming the Alarm System with Remote
Entry
[CF80310(R)05/96]
Your Remote Entry System will automatically arm the factory
installed Anti-Theft System when the doors are locked, and
automatically disarm it when the doors are unlocked. The
remote will also reset the anti-theft alarm (when the driver's
door is unlocked or the PANIC control is pressed on a
programmed remote entry transmitter) if it was triggered.
*
[CF80320(R)01/96]
The remote entry system may not arm and disarm non-factory
installed anti-theft systems.
%*
[CF80500(R)05/96]
Replacing the Batteries
*
[CF80510(R)05/96]
The remote is powered by two coin type three-volt lithium 2016
batteries (included) that should last for several years of normal
use. If you notice a significant decrease in operating range, the
batteries should be replaced. Replacement batteries can be
purchased at most pharmacies, watch stores or at your Ford or
Lincoln-Mercury dealer.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

Controls and Features
97
%*
[CF80560(R)05/96]
Replacing lost transmitters
[CF80562(R)01/96]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[CF80564(R)01/96]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[CF80570(R)01/96]
Illuminated Entry System (If equipped)
*
[CF80574(R)01/96]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
[CF80578(R)04/96]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
%*
[CF80600(R)01/96]
Battery Saver
[CF80610(R)04/96]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
*
[CF80630(R)01/96]
This will prevent draining of the battery if these lights have
been left on inadvertently or if a door is not completely closed.
Battery voltage to these lamps will be restored when the remote
entry transmitter is used, any door is opened, or the ignition
key is turned on again.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

Controls and Features
99
[CF81340(R)01/96]
Remember, all doors must be fully closed for the anti-theft
system to arm. If a door has been left open or ajar, and you
press the remote entry transmitter twice to confirm the doors
are locked, two short horn chirps will warn you that the
anti-theft system is not arming.
[CF81360(R)05/96]
When you get a single horn chirp by pressing the LOCK control
twice within 5 seconds on your remote entry transmitter, you
can be assured that all doors are locked and the anti-theft
system is arming.
% [CF81400(R)01/96]
Disarming the System
[CF81410(R)04/96]
An armed or activated system can be disarmed if you:
[CF81420(R)05/96]
n
Unlock the doors by pressing the remote entry transmitter
UNLOCK control.
[CF81435(R)01/96]
n
Unlock any door with a key.
[CF81439(R)04/96]
n
Turn ignition to the ON or ACC position.
[CF81440(R)04/96]
n
Pressing the remote entry PANIC button will disarm the
anti-theft system only when the anti-theft alarm is triggered
and sounding.
[CF81442(R)04/96]
When unlocking the vehicle with a key, turn the key all the
way to the end of its travel or the system may not disarm.
*
[CF81448(R)01/96]
NOTE: The flashing lights and honking horn will shut off
automatically within 2 minutes 45 seconds after the
system is triggered. It will trigger again if another
intrusion occurs. However, the starter circuit remains
disabled until the system is disarmed.
*
[CF81450(R)01/96]
The anti-theft system is designed to work with the factory
installed remote entry system. It may not work with other
remote entry systems.
File:05uncfr.ex
Update:Thu Mar 20 08:51:14 1997

176
[GF16190(R)05/96]
Four-wheel drive operation (4x4 HIGH or 4x4 LOW) on dry
pavement is not recommended. Operating the vehicle in
four-wheel drive on dry pavement will increase noise, vibration,
tire wear, decrease fuel economy, and make four-wheel drive
disengagement difficult for the transfer case.
[GF16200(R)05/96]
Electric shift system indicator lights
[GF16210(R)05/96]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[GF16220(R)05/96]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[GF16230(R)05/96]
n
4WD High Ð Only the 4WD light is lit.
[GF16240(R)05/96]
n
4WD LOW mode Ð Both the 4WD and 4WD LOW lights
are lit.
[GF16250(R)05/96]
To shift from Two-Wheel Drive to 4WD High:
[GF16260(R)05/96]
To shift into 4WD High rotate the 4WD switch located on the
instrument panel to 4x4 High. This shift can be done at a stop
or at speeds up to 55 miles per hour (88 km/h). When the
vehicle is driven, the automatic locking hubs will engage. If the
vehicle is stopped while in 4WD and the vehicle direction is
reversed from the previous direction, the automatic locking hubs
will momentarily disengage and re-engage. The automatic
locking hubs may click as they automatically engage in the new
direction.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

178
*
[GF16330(R)05/96]
For example:
[GF16340(R)05/96]
If you were driving the vehicle forward in 4WD, the
automatic locking hubs will disengage the next time the
vehicle is driven in reverse in two-wheel drive for
approximately 10 feet (3 meters) in a straight line.
[GF16350(R)05/96]
If you were driving the vehicle in reverse in 4WD, the
automatic locking hubs will disengage the next time the
vehicle is driven forward in two-wheel drive for
approximately 10 feet (3 meters) in a straight line.
*
[GF16360(R)05/96]
Operating in two-wheel drive mode with the hubs locked
increases fuel consumption, noise, vibration, and wear. For
prolonged two-wheel drive operation on dry pavement,
disengagement of the automatic locking hubs, which is not
required for two-wheel drive operation, stops all movement of
front-wheel drive components while operating in two-wheel
drive.
[GF16370(R)05/96]
During axle break-in or operation in extremely cold
temperatures, the automatic locking hubs may not release
completely. It may be necessary to drive the vehicle for 10 to 15
minutes before repeating the release procedure.
[GF16380(R)05/96]
To shift from 4x4 HIGH or 2WD to 4x4 LOW:
[GF16390(R)05/96]
Stop the vehicle, depress the brake and place the automatic
transmission in N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4x4 LOW. Both the 4WD and 4WD LOW
lights are now lit.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

Driving
181
[GF17040(R)05/96]
4WD system indicator lights
[GF17050(R)05/96]
A 4WD light and a 4WD LOW light are located in the
instrument cluster.
[GF17060(R)05/96]
n
2H position Ð Neither the 4WD or the 4WD LOW lights are
lit.
[GF17070(R)05/96]
n
4H position Ð Only the 4WD light is lit.
[GF17080(R)05/96]
n
N position Ð Neither the 4WD or 4WD LOW lights are lit.
[GF17090(R)05/96]
n
4L position Ð Both the 4WD and the 4WD LOW lights are
lit.
*
[GF17100(R)05/96]
To shift from 2H to 4H:
*
[GF17110(R)05/96]
Stop the vehicle and engage the manual locking hubs by
turning both hub lock selector knobs clockwise to the LOCK
position. Move the transfer case shift lever straight back to the
4H position. After both hubs have been turned to the LOCK
position, shifts between 2H and 4H (or 4H to 2H) may take
place at any speed.
[GF17120(R)05/96]
10-1/2 pica
art:0021182-A
Locking hub positions
[GF17130(R)05/96]
NOTE: Do not drive the vehicle in 4H or 4L with the manual
locking hubs in the FREE position.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

Roadside Emergencies
239
%*
[ER25100(R)02/96]
Preparing Your Vehicle
*
[ER25200(R)02/96]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[ER25300(R)02/96]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[ER25400(R)02/96]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[ER25500(R)02/96]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[ER25600(R)02/96]5.
Turn on the heater fan in both vehicles. Turning on the fan
helps protect the electrical system from voltage surges. Turn
off all other switches and lights in both vehicles to prevent
possible damage to either vehicle's electrical systems.
%*
[ER25700(R)02/96]
Connecting the jumper cables
*
[ER25800(R)02/96]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[ER25900(R)02/96]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[ER26000(R)02/96]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

Roadside Emergencies
245
[ER33000(R)01/96]
4x2ÐManualtransmission
*
[ER33100(R)01/96]
n
Release the parking brake.
[ER33200(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33300(R)01/96]
n
Maximum speed is limited by towing equipment
manufacturer's recommendation, unlimited distance.
[ER33400(R)01/96]
4x4ÐManualshifttransfercase
*
[ER33500(R)01/96]
n
Release the parking brake.
[ER33600(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER33700(R)01/96]
n
Place the transfer case gearshift in the neutral position.
[ER33800(R)01/96]
n
Set the manual locking hubs in the FREE position.
[ER33900(R)01/96]
n
Maximum speed is 55 mph (88 km/h), unlimited distance.
[ER34000(R)01/96]
4 x 4 Electric shift transfer case
*
[ER34200(R)01/96]
n
Release the parking brake.
[ER34300(R)01/96]
n
Place the transmission gearshift in the neutral position.
[ER34400(R)05/96]
n
Ensure the transfer case is in 2H and the auto hubs are
unlocked.
[ER34600(R)01/96]
NOTE: Both the 4WD and 4WD Low indicator lights in the
instrument panel will be off when the 4WD switch is
in 2WD.
[ER34700(R)01/96]
For automatic transmissions:
[ER34800(R)01/96]
n
Maximum speed is 35 mph (56 km/h).
[ER34900(R)01/96]
n
Maximum distance is 50 miles (80 km).
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997