1997 FORD RANGER clock

126
[SS12645(R)01/96]
RWARNING
If the light fails to illuminate when the passenger air bag
switch is in the OFF position and the ignition switch is
in ON, have the passenger air bag switch serviced at
your Ford or Lincoln-Mercury dealer immediately.
[SS12650(R)01/96]
The passenger air bag will remain off until it is turned on.
When the infant seat is removed, turn the air bag on. To turn
the passenger air bag on:
[SS12655(R)01/96]1.
Insert the ignition key into the switch.
[SS12660(R)01/96]2.
Rotate the ignition key counterclockwise until it points to the
ON printed on the instrument panel.
[SS12665(R)01/96]3.
Remove the ignition key from the switch.
[SS12670(R)01/96]4.
Check that the amber OFF light is not illuminated when the
ignition switch is placed in ON.
[SS12675(R)01/96]
RWARNING
If the light is illuminated when the passenger air bag
switch is in the ON position and the ignition switch is in
ON, have the passenger air bag switch serviced at your
Ford or Lincoln-Mercury dealer immediately.
[SS12680(R)01/96]
The amber OFF light warns the driver and any passengers that
the passenger air bag is turned off. The passenger air bag
should be turned off ONLY when the rear-facing infant seat is
installed at the right front or center front seats.
[SS12685(R)05/96]
RWARNING
Keep the passenger air bag turned on unless there is a
rear-facing infant seat installed in the front seat. When
the passenger air bag switch is turned off, the passenger
air bag will not inflate in a collision.
File:06unssr.ex
Update:Fri Mar 21 09:43:41 1997

Driving
181
[GF17040(R)05/96]
4WD system indicator lights
[GF17050(R)05/96]
A 4WD light and a 4WD LOW light are located in the
instrument cluster.
[GF17060(R)05/96]
n
2H position Ð Neither the 4WD or the 4WD LOW lights are
lit.
[GF17070(R)05/96]
n
4H position Ð Only the 4WD light is lit.
[GF17080(R)05/96]
n
N position Ð Neither the 4WD or 4WD LOW lights are lit.
[GF17090(R)05/96]
n
4L position Ð Both the 4WD and the 4WD LOW lights are
lit.
*
[GF17100(R)05/96]
To shift from 2H to 4H:
*
[GF17110(R)05/96]
Stop the vehicle and engage the manual locking hubs by
turning both hub lock selector knobs clockwise to the LOCK
position. Move the transfer case shift lever straight back to the
4H position. After both hubs have been turned to the LOCK
position, shifts between 2H and 4H (or 4H to 2H) may take
place at any speed.
[GF17120(R)05/96]
10-1/2 pica
art:0021182-A
Locking hub positions
[GF17130(R)05/96]
NOTE: Do not drive the vehicle in 4H or 4L with the manual
locking hubs in the FREE position.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

182
[GF17140(R)05/96]
NOTE: Do not drive the vehicle with the left and right
manual locking hubs set to different positions.
*
[GF17150(R)05/96]
To shift from 4H to 2H:
*
[GF17160(R)05/96]
Move the transfer case shift lever forward to the 2H position.
This can be done at any speed. However, the front driveline
will remain engaged to the front wheels until the manual
locking hubs are disengaged. To disengage the manual locking
hubs, stop the vehicle and rotate both hub lock selector knobs
counterclockwise to the FREE position.
*
[GF17170(R)05/96]
Operating in 2H with the hubs in the LOCK position increases
fuel consumption, noise, vibration, and wear. For prolonged 2H
operation on dry pavement, set the manual locking hubs to the
FREE position.
*
[GF17180(R)05/96]
To shift between 4H and 4L:
[GF17190(R)05/96]
Stop the vehicle and place the automatic transmission into N
(Neutral) or depress the clutch on vehicles with a manual
transmission. Pull the transfer case shift lever to the left and
shift the transfer case to the desired 4H or 4L position. This
shift should be with one continuous motion without pausing in
the N position. Pausing in the neutral position can result in gear
clash and difficult shifting. If while shifting between 4H and 4L,
the transfer case gets stuck in the N position or is difficult to
shift into either 4H or 4L, it may be necessary to let the vehicle
roll slightly and/or turn off the engine (particularly on vehicles
equipped with automatic transmissions).
[GF17200(R)05/96]
To shift between N (Neutral) and either 4H or 4L
[GF17210(R)05/96]
To shift into N (Neutral), stop the vehicle and engage the
parking brake. Place the automatic transmission into N (Neutral)
or depress the clutch on manual transmission vehicles. From
either the 4H or 4L position, pull the transfer case shift lever to
the left and move the transfer case shift lever to the N (Neutral)
position. The N (Neutral) position should only be used for
vehicle towing.
File:09ungfr.ex
Update:Thu Mar 20 08:55:24 1997

234
[ER18301(R)01/96]
10-1/2 pica art:0020297-E
Front axle jacking point
[ER18401(R)01/96]
c. Turn the jack handle clockwise until the wheel is a
maximum of one inch off the ground.
[ER18551(R)01/96]
10-1/2 pica
art:0021187-B
Rear axle jacking point
[ER18650(R)01/96]
NOTE: Do not use the differential housing as a lift point.
File:10unerr.ex
Update:Thu Mar 20 08:56:46 1997

300
*
[MC46300(R)03/96]
Removing the headlamp bulb
*
[MC46400(R)01/96]1.
Make sure that the headlamp switch is in the OFF position.
[MC46502(R)01/96]2.
Lift the hood. Remove the electrical connector behind the
headlamp by grasping the wires and pulling it rearward.
*
[MC46700(R)01/96]3.
Remove the bulb retaining ring by turning it 1/8 of a turn to
free it from the socket. Then slide the ring off the plastic
base.Keep the ring.You must use it again to hold the new
bulb in place.
*
[MC46800(R)01/96]4.
Carefully remove the bulb assembly from its socket by
gently pulling it rearward without turning.
*
[MC46900(R)03/96]
Installing the headlamp bulb
*
[MC47000(R)01/96]1.
With the flat side of the bulb's plastic base facing upward,
insert the glass end of the bulb into the socket. You may
need to turn the bulb left or right to line up the grooves in
the plastic base with the tabs in the socket. When the
grooves are aligned, push the bulb into the socket until the
plastic base contacts the rear of the socket.
*
[MC47100(R)01/96]2.
Slip the bulb retaining ring over the plastic base until it
contacts the rear of the socket. Lock the ring into the socket
by rotating it clockwise until you feel a ªstop.º
*
[MC47200(R)01/96]3.
Push the electrical connector into the rear of the plastic base
until it snaps, locking it into position.
*
[MC47300(R)01/96]4.
Turn the headlamps on and make sure that they work
properly. If the headlamp was correctly aligned before you
changed the bulb, you should not need to align it again.
File:11unmcr.ex
Update:Thu Mar 20 08:58:43 1997

347
Index
Climate control system.................. 64
Clock........................ 34,55
Clutch
fluid........................ 263
fluid reservoir.................261, 263
operation while driving............... 170
recommended shift speeds.............. 173
shifting the gears.................. 171
specifications.................... 313
Cold engine starting.................. 148
Combination lap and shoulder belts.........110, 112
Controls
mirrors........................ 86
power seat..................... 109
Convenience kit in cargo area.............. 229
Coolant (see Engine coolant)
checking and adding................ 265
preparing for storage................ 309
specifications.................... 313
temperature gauge.................. 22
warnings...................... 265
Cooling fan...................... 250
Crankcase emission filter................ 311
Customer Assistance Centre, Ford of Canada....... 324
D
Daytime running light system.............. 63
Defects, reporting................... 315
Defrost, windshield................. 67,70
Dipstick
automatic transmission fluid...........271, 273
engine oil..................... 258
power steering fluid................. 268
Disabled vehicle (see Towing).............. 242
File:unixr.ex
Update:Thu Mar 20 09:01:44 1997