1997 FORD MUSTANG brake

84 %
*
[CF46460(M )05/96]
Fog Lamps (If equipped)
[CF46540(M )03/96]
The fog lamps switch is located on the console
to the left of the parking brake. The fog lamps
act as a supplement to the low beam headlamps
under limited visibility conditions such as rain,
snow, dust or fog and operate only when the
low beam headlamps are on.
[CF46550(M )04/96]
one third page art:0011228-A
Fog lamp switch
[CF46560(M )04/96]
q
To turn the fog lamps on, push the concave
side of the rocker switch. An indicator light
will glow when the lamps are on.
[CF46570(M )04/96]
q
To turn off, push the raised side of the
switch.
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

85
% [CF46600(M )12/95]
Convertible (If equipped)
[CF46700(M )12/95]
NOTE: Do not store articles behind rear seat.
Articles stored in the convertible top
stowage compartment may break the
rear glass window when the top is
lowered.
% [CF46800(M )12/95]
Lowering the Convertible Top
[CF46900(M )12/95]
The convertible top can be lowered with the side
windows either up or down.
[CF47000(M )12/95]
NOTE: CONVERTIBLE TOP WILL NOT
OPERATE UNLESS PARKING BRAKE
IS ENGAGED. Do not lower the top
while the vehicle is moving because
the top may be severely damaged.
Also, do not lower the top when the
top material is wet.
[CF47100(M )12/95]
To lower the convertible top:
[CF47200(M )12/95]
1. Bring vehicle to a complete stop. Engage the
parking brake.
[CF47300(M )12/95]
2. Check the convertible top stowage
compartment behind the rear seat to be sure
it is empty and ready to receive the top.
[CF47400(M )12/95]
3. Unclamp the top from the windshield header
at both the right and left sides by pulling
each clamp rearward until the hook in the
windshield header is free. The clamps are
flush with the header when in the closed
position.
[CF47500(M )12/95]
4. Close the windshield header clamps
immediately after disengagement, to avoid
cutting the top material and to permit
installation of the vinyl boot.
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

90 [CF49200(M )12/95]6. Removal
[CF49300(M )04/96]
one third page art:0011361-B% [CF49400(M )12/95]
Raising the Convertible Top
[CF49500(M )12/95]
NOTE: CONVERTIBLE TOP WILL NOT
OPERATE UNLESS PARKING BRAKE
IS ENGAGED. Do not raise the top
while the vehicle is moving because
the top may be severely damaged.
[CF49600(M )12/95]
To raise the convertible top:
[CF49700(M )12/95]
1. Bring the vehicle to a complete stop. Engage
the parking brake.
[CF49800(M )12/95]
2. Remove the boot cover, place it in the bag
and store it in the luggage compartment.
[CF49900(M )12/95]
3. Lower the front and rear side windows.
[CF50000(M )12/95]
4. Push the convertible top button in, holding it
until the top unfolds and moves forward
toward the windshield header.
[CF50100(M )12/95]
5. Open both top clamps before the top meets
the windshield header.
[CF50200(M )12/95]
6. Continue to use the top motor to raise the
top until it has reached the fully closed
position flush to the header.
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

91 [CF50300(M )12/95]
7. The two pins under the forward edge of the
top should seat themselves in the matching
holes in the header.
[CF50400(M )12/95]
8. To fasten both clamps securely, push the
clamp handles into the header on the top
until they are flush with the header. Pulling
down on the header at the center grip while
closing the latches may assist in fastening
the clamps.
[CF50500(M )12/95]
9. Raise the front and rear side windows.
[CF50510(M )04/96]
NOTE: Make sure to release the parking brake
before driving the vehicle.
% [CF50600(M )12/95]
Convertible Top and Padded Molding Care
[CF50700(M )12/95]
To avoid damage to the vinyl top and moldings,
use only an approved Ford cleaner, or
equivalent. Do not use stiff bristle brushes or
abrasive material or cleaners.
[CF50800(M )12/95]
Hot waxes applied by automatic car washes can
affect the cleanability of vinyl material.
[CF50900(M )12/95]
NOTE: Using high water pressure or wand
type car washes against the convertible
top and windows may cause water
leaks and possible seal damage.
% [CF51000( ALL)12/95]Positive Location Floor Mat
[CF51100(MBC )12/95]
When installing or removing the driver's side
floor mat you must attach/detach the positive
location grommet from the hook on the floor.
The hook is just forward of the left hand track
of the driver's seat.
File:05rccfm.ex
Update:Thu Apr 3 07:41:31 1997

114
%*
[SS12200( ALL)02/96]
Combination Lap and Shoulder
Belts
*
[SS12300( ALL)12/95]
While your vehicle is in motion, the combination
lap and shoulder belt adjusts to your movement.
However, if you brake hard, corner hard or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap and shoulder belt
locks and helps reduce your forward movement.
*
[SS12400( ALL)01/96]
After you get into your vehicle, close the door
and lock it. Then adjust the seat to the position
that suits you best.
[SS12500(M )12/95]
Before fastening the front seat belt, make sure
the shoulder belt passes through the belt holder
on the top of the seatback.
[SS12600( ALL)12/95]
To fasten the belt,pull the lap/shoulder belt
from the retractor so that the shoulder portion of
the belt crosses your shoulder and chest. Be sure
the belt is not twisted. If it is, remove the twist.
Insert the belt tongue into the proper buckle
until you hear a snap and feel it latch. Make
sure the tongue is securely fastened in the
buckle.
[SS12800(M )04/96]
one third page art:0011200-C
Fastening the front seat combination lap and shoulder belt
(coupe models)
File:06rcssm.ex
Update:Mon Feb 24 10:16:50 1997

150 [TO01000(M )12/95]3.If you have an automatic transmission,
make sure that the gearshift is in P (Park)
and the parking brake is set before you turn
the key.
[TO01100(M )12/95]
If you have a manual transmission, make
sure that the parking brake is fully set, push
the clutch pedal to the floor, and put the
gearshift into Neutral before you turn the
key.The starter will operate only if the
clutch pedal is pushed in all the way.
*
[TO01300( ALL)02/96]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to the
Instrumentationchapter.
%*
[TO01400( ALL)01/96]
Starting Your Engine
*
[TO01500( ALL)01/96]
To start your engine:
*
[TO01600( ALL)01/96]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[TO01700( ALL)01/96]
2. Turn the ignition key to the ON position.
*
[TO01800( ALL)01/96]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
*
[TO01900( ALL)01/96]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[TO02000( ALL)01/96]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
File:08rctom.ex
Update:Thu Apr 3 07:46:27 1997

151 %
*
[TO02100( ALL)01/96]
For a cold engine:
*
[TO02200( ALL)01/96]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[TO02300( ALL)01/96]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
%*
[TO02400( ALL)01/96]
For a warm engine:
*
[TO02500( ALL)01/96]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[TO02600( ALL)01/96]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[TO02700( ALL)01/96]
After you start the engine, let it idle for a few
seconds. Keep your foot on the brake pedal and
put the gearshift lever in gear. Release the
parking brake. Slowly release the brake pedal
and drive away in the normal manner.
*
[TO02800( ALL)12/95]
NOTE: Your vehicle has an interlock that
prevents you from shifting out of P
(Park) unless your foot is on the brake
pedal.
File:08rctom.ex
Update:Thu Apr 3 07:46:27 1997

157
Driving
%*
[GF00500( ALL)01/96]
Brakes
%*
[GF00600( ALL)01/96]
Applying the Brakes
[GF00700( ALL)12/95]
Braking non ABS models
[GF00800(M )04/96]
All models have power 4-wheel disc brakes.
They adjust automatically as the brake pads or
linings wear down.
*
[GF01200( ALL)01/96]
Apply the brake pedal gradually. Use the
ªsqueezeº technique Ð push on the brake pedal
with a steadily increasing force. This allows the
wheels to continue to roll while you are slowing
down, which lets you steer properly.
[GF01300( ALL)12/95]
On vehicles without anti-lock brakes, extreme
braking can make the wheels lock and slide,
possibly decreasing your control of the steering.
If you lock the wheels, release the brake pedal
and repeat the ªsqueezeº technique.
[GF01301(M )02/97]
Occasional brake noise is normal and often does
not indicate a performance concern with the
vehicle's brake system. In normal operation,
automotive brake systems may emit occasional
or intermittent squeal or groan noises when the
brakes are applied. Such noises are usually
heard during the first few brake applications in
the morning; however they may be heard at any
time while braking and can be aggravated by
environmental conditions such as cold, heat,
moisture, road dust, salt or mud. If a
ªmetal-to-metalº or ªcontinuous grindingº sound
is present while braking, the brake linings may
be worn-out and should be inspected by a
qualified service technician.
File:09rcgfm.ex
Update:Mon Feb 24 10:18:27 1997