1997 FORD E SERIES jump start

On vehicles equipped with dual
rear wheels retighten the wheel
lug nuts to the specified torque at
160 km (100 miles), and again at
800 km (500 miles) of new vehicle
operation and at intervals specified
in the ªService Guide.º
On vehicles equipped with single
rear wheels retighten the lug nuts
to the specified torque at 800 km
(500 miles) of operation after any
wheel change or any time the lug
nuts are loosened.
Model Bolt Size Wheel Lug nut Torque*
N²M Ft-Lb
E-150 1/2-20 135 100
E-250, E-350
and E-Super
Duty9/16-18 190 140
* Torque specifications are for nut and bolt threads free of dirt and
rust. Do not use oil or grease on threads. Use only Ford recommened
replacement fasteners.
JUMP STARTING YOUR
VEHICLE
The gases around the
battery can explode if
exposed to flames, sparks, or lit
cigarettes. An explosion could
result in injury or vehicle
damage.
com_jump-starting.01
Roadside emergencies
120

Do not push-start your
vehicle. You could damage
the catalytic converter. For
further information, seeJumper
Cablesin the Index.
Batteries contain sulfuric
acid which burns skin,
eyes, and clothing.
Connecting the jumper cables
1. Position the vehicles so that
they do not touch one another.
2. Switch off the engine. Switch off
any unnecessary electrical
equipment.
3. Connect the positive (+)
terminal of the discharged battery
(1) to the positive (+) terminal of
the booster battery (2).
4. Connect one end of the second
lead to the negative (-) terminal of
the booster battery (3) and the
other end to a metal part of the
engine to be started (4), not to the
negative (-) terminal of the
discharged battery.
5. Make sure that the jump leads
are clear of moving parts of the
engine.
+–
+–
3
2
1
4
com_connecting_cables.01
Roadside emergencies
121

Do not connect the end of
the second cable to the
negative ([-]) terminal of the
battery to be jumped. A spark
may cause an explosion of the
gases that surround the battery.
Jump starting
1. Start the booster vehicle and
run the engine at moderately
increased speed.
2. Start the engine of the vehicle
with the discharged battery.
3. Once the engine has been
started, run both vehicles for a
further three minutes before
disconnecting the leads.
Removing the jumper cables
1. Remove the jumper cables in
reverse order. Take the cable off
the metallic surface (1) first,
followed by the cable on the
negative (-) booster battery
terminal (2).
2. Remove the cable from the
positive (+) terminal of the booster
battery (3) and then the
discharged battery (4).
3. After the disabled vehicle has
been started, allow it to idle for a
while so the engine can ªrelearnº
its idle conditions.
+–
+–
2
3
4
1
com_jump_starting.01
com_removing_cables.01
eco_wrecker_towing
Roadside emergencies
122

Idle
relearning ................................145
Ignition .........................................23
Inspection
maintenance testing ...............164
Jump-starting your vehicle 120,122
attaching cables ......................121
disconnecting cables ..............122
Lamps
cargo lamps ...............................30
courtesy lamps ..........................31
Lights, warning and indicator
air bag ..........................................9
anti-lock brakes (ABS) ..............8
brake ............................................8
charging system ..........................9
check engine ...............................8
door ajar ....................................10
engine oil pressure ...................10
high beam .................................10
safety belt ...................................9
Load limits
trailer towing ............................89
Lubricant specifications ...........175
Odometer .....................................13
Overdrive .....................................24
Parking brake
operation ..............................81,82
Parts (see Motorcraft parts) ....174
Power features
door locks ..................................32
mirrors .......................................31
Power point electrical outlet .....17
Power steering
fluid, checking and adding ....140
Refill capacities for fluids ........174
Relays .................................102,111
Remote entry system .................34
locking/unlocking doors ...........34
panic alarm ...............................35
replacement/additional
transmitters ...............................36replacing the batteries .............35
Reporting safety defects ..........183
Safety restraints
adjusting the safety belts .........49
automatic locking mode
(retractor) .................................47
extension assembly ..................50
for children ...............................58
lap and shoulder belts .............45
maintenance ..............................51
proper use .................................43
warning light and chime ..........51
Safety seats for children
automatic locking mode
(retractor) .......................61,62,66
Seats ............................................37
adjusting the seat, manual .......37
adjusting the seat, power ........38
bench seat .................................39
lumbar support .........................39
quick release rear captain's
chair ...........................................41
Servicing your vehicle ..............124
precautions when servicing ...124
Special notice ................................2
ambulance conversions ..............2
diesel-powered vehicles .............3
Speed control ..............................28
accelerating ...............................29
resetting ....................................29
resuming a set speed ...............30
turning off .................................28
Speedometer ...............................12
Starting your vehicle ..................73
preparing to start your
vehicle .......................................74
starting a warm engine ............77
Steering, power ...........................82
Steering wheel
tilting .........................................26
Tires ...........................................153
changing ...........................112,114
Index
184