1997 FORD CONTOUR lock

Driving
139
[GF11000(ALL)12/95]
Downshifting
*
[GF11100(ALL)03/96]
When you slow down or climb a steep hill, always downshift
before the engine starts to lose power. Downshifting reduces the
chance of stalling and gives your vehicle better acceleration to
increase speed again.
*
[GF11200(ALL)01/96]
When you drive down steep hills, downshifting helps you keep
a safe speed and helps prevent unnecessary wear on the brakes.
*
[GF11300(ALL)01/96]
When you come to a stop, do not downshift through each gear.
Disengage the clutch and use the brake as necessary.
Downshifting through the gears decreases your vehicle's fuel
economy.
[GF11400(ALL)12/95]
Do not attempt to shift into 1 (First) gear with the clutch pedal
depressed at speeds higher than 20 mph (30 km/h). If you do,
it could cause a complete clutch failure, making your vehicle
inoperative.
%*
[GF11500(ALL)01/96]
Driving With a Heavy Load
*
[GF11600(ALL)01/96]
There are limits to the amount of weight your vehicle can carry
or tow. The total weight of your vehicle, plus the weight of the
passengers and cargo, should never be more than the Gross
Vehicle Weight Rating (GVWR). Also, the weight that your
vehicle carries over the front axle and rear axle should never be
more than the Gross Axle Weight Rating (GAWR) for the
respective axle.
%*
[GF11700(ALL)12/95]
You can find your vehicle's GVWR and GAWR on the Safety
Compliance Certification Label on the left front door lock facing
or on the door latch post pillar.
*
[GF11800(ALL)01/96]
The weight limits of your vehicle's tires affect the GVWR or
GAWR limitations. Usage of replacement tires with higher
weight limits than originals does not increase GVWR or GAWR.
Usage of lower capacity replacement tires may lower GVWR
and GAWR limitations.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

140
*
[GF11900(ALL)01/96]
RWARNING
Do not exceed the GVWR or the GAWR specified on the
Safety Compliance Certification Label.
%*
[GF12000(ALL)01/96]
Limiting Your Vehicle's Load
[GF12100(ALL)12/95]
The load that you add to your vehicle must not exceed the
maximum load stated on the Safety Compliance Certification
Label attached to the left front door pillar or the left front door
lock facing.
*
[GF12200(ALL)01/96]
To figure the weight of your vehicle's load, add the weights of:
*
[GF12300(ALL)01/96]
n
the driver and passengers
*
[GF12400(ALL)01/96]
n
luggage and any other items that you put in your vehicle
*
[GF12500(ALL)12/95]
n
the tongue load of the loaded trailer
*
[GF12600(ALL)01/96]
n
the weight of any equipment that has been added to your
vehicle since it was delivered to your dealer
*
[GF12700(ALL)01/96]
If you do not know the actual weights of these items, use the
following procedure to figure the weight of a load:
*
[GF12800(ALL)01/96]1.
Weigh your vehicle without the driver, passengers and
luggage. You might take your vehicle to a shipping company
or an inspection station for trucks.
*
[GF12900(ALL)01/96]2.
Then weigh your vehicle with the driver, passengers and
luggage.
*
[GF13000(ALL)01/96]3.
Subtract the first reading from the second to figure the total
weight of the load.
*
[GF13100(ALL)11/92]
After determining this load, you must also make sure that the
total weight of your vehicle, plus the load it carries, is less than
its GVWR. Also, make sure that the weight your vehicle carries
over each axle is less than the GAWR for the respective axle.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Driving
141
*
[GF13200(ALL)12/95]
You can find the GVWR and GAWR on the Safety Compliance
Certification Label on the left front door lock facing or the door
latch post pillar.
*
[GF13300(ALL)01/96]
If your vehicle exceeds the GVWR, remove cargo from your
vehicle accordingly. If your vehicle exceeds the GAWR for
either axle, shift the load or remove cargo accordingly.
*
[GF13400(ALL)01/96]
RWARNING
Improper distribution of your vehicle's load or carrying
weight in excess of the amount shown on the tire decal
can cause rapid tire wear or loss of vehicle control.
%*
[GF13500(ALL)01/96]
Trailer Towing
[GF13600(ALL)12/95]
Your vehicle is capable of towing a trailer of up to a maximum
of 1,000 lbs. (454 kg) gross trailer weight with a maximum
tongue load of 100 lbs (45 kg). It should also have 25 sq. ft. (2.3
sq. meters) or less frontal area. Do not drive faster than 55 mph
(90 km/h) while towing a 1,000 lb. (454 kg) trailer.
*
[GF13700(ALL)12/95]
Your vehicle does not come from the factory fully equipped to
tow. No towing packages are available through Ford or
Lincoln/Mercury dealers.
*
[GF13800(ALL)12/95]
Because towing a trailer puts extra strain on your vehicle, you
must follow certain precautions for your safety and the good of
your vehicle:
*
[GF13900(ALL)12/95]
n
Stay within the load limits when you tow. (SeeKnowing Your
Vehicle's Load Limits.)
*
[GF14000(ALL)01/96]
n
Carefully and thoroughly prepare your vehicle for towing,
making sure to use the right equipment and to attach it
properly. (SeePreparing to Towin this chapter.)
*
[GF14100(ALL)01/96]
n
Use extra caution when driving your vehicle while you tow.
(SeeDriving while you towin this chapter.)
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

146
*
[GF18100(ALL)01/96]
n
Do not quickly move the steering wheel unless necessary.
*
[GF18200(ALL)01/96]
n
Drive slower than you normally would.
*
[GF18300(ALL)01/96]
n
Give your vehicle more distance to stop.
*
[GF18400(ALL)12/95]
n
Pump the brake pedal steadily and evenly to avoid locking
your wheels.
*
[GF18500(ALL)01/96]
n
Consider using one of the lower gears.
*
[GF18600(ALL)01/96]
RWARNING
To avoid losing control on slippery roads, do not
downshift into 1 (First) with the automatic transaxle
when moving faster than 20 mph (32 km/h). Do not
downshift into 1 (First) with the manual transaxle when
moving faster than 10 mph (16 km/h).
*
[GF18700(ALL)03/96]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
*
[GF18800(ALL)01/96]
If you have an automatic transaxle and your vehicle gets stuck
(for example, in mud or snow), you may try to ªrockº it out of
the spot. Shift, in a steady rhythm, between forward and reverse
gears. While in each gear, press lightly on the accelerator and
release.
*
[GF18900(ALL)01/96]
RWARNING
Do not spin the wheels at over 35 mph (55 km/h). The
tires may fail and injure a passenger or bystander.
File:09cdgfo.ex
Update:Thu Sep 12 11:04:39 1996

Roadside Emergencies
163
[ER06700(ALL)12/95]
17-1/2 pica
art:0000531-B
The temporary spare tire
%*
[ER06800(ALL)03/96]
Preparing to Change the Tire
*
[ER06900(ALL)01/96]1.
Make sure that your vehicle will not move or roll. If you
have an automatic transaxle, put the gearshift in P (Park). If
you have a manual transaxle, put the gearshift in 1 (First).
Set the parking brake and block the wheel that is diagonally
opposite the tire that you are changing.
*
[ER07000(ALL)12/95]
When one of the front wheels is off the ground, the transaxle
alone will not prevent the vehicle from moving or slipping off
the jack, even if the vehicle is in P (Automatic) or 1 (Manual).
To prevent the vehicle from moving when you change one of
the front tires, put a block behind the wheel that is diagonally
opposite the tire.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

164
*
[ER07100(ALL)03/96]
RWARNING
If the vehicle slips off the jack, you or someone else
could be seriously injured.
*
[ER07200(ALL)01/96]2.
Get out the spare tire and jack.
*
[ER07300(ALL)03/96]
RWARNING
To avoid injury, never run the engine with one wheel off
the ground, such as when changing a tire.
[ER07400(ALL)12/95]3.
Remove the wheel cover from the wheel with the tapered
end of the wheel lug wrench. Insert and twist the handle,
then pry against the inner wheel cover flange. For
information about removing optional wheel center ornaments
seeStyled Polycast Wheel Ornamentslater in this section.
[ER07500(ALL)12/95]4.
Loosen the wheel lug nuts by pulling up on the handle of
the wrench one-half turn counterclockwise. Do not remove
the wheel lug nuts until you raise the tire off the ground.
For information about removing anti-theft lug nuts, see
Anti-Theft Wheel Lug Nutslater in this section.
%*
[ER07600(ALL)01/96]
Removing and Replacing the Tire
[ER07700(ALL)12/95]1.
Place the scissors-type jack under the side of the vehicle and
adjust the jack height with the jack handle. The jack should
fit in the notch in the vertical rocker panel flange which is
nearest to the wheel to be changed. The front and rear
jacking notches on each side of the vehicle are marked by
arrows in the rocker panel.
[ER07800(O )02/96]
On sport models with ªskirts,º you must remove a portion
of the skirt before placing the jack under the vehicle.
Squeeze the removeable portion of the skirt and pull down.
A tether connects it to the rocker panel.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

166
[ER08100(ALL)12/95]
17-1/2 pica art:0000528-E
The notches for the jack
*
[ER08200(ALL)12/95]2.
Turn the jack handle clockwise until the wheel clears the
ground. Remove the wheel lug nuts.
*
[ER08300(ALL)03/96]3.
Replace the flat tire with the spare tire, making sure that the
air valve stem is facing outward.
*
[ER08400(ALL)03/96]4.
Reinstall the lug nuts, tightening until the wheel is snug
against the hub. The beveled edges on the lug nuts face
inward. Do not fully tighten the lug nuts until you lower the
vehicle. If you do, you could force the vehicle off the jack.
*
[ER08500(ALL)03/96]5.
Lower the vehicle by turning the jack handle
counterclockwise.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996

Roadside Emergencies
167
*
[ER08600(ALL)03/96]6.
Remove the jack and fully tighten the lug nuts in the order
shown in the following illustration. As soon as possible, have
your dealer or a qualified service technician check the lug
nuts for proper torque specifications.
[ER08700(ALL)12/95]
13-1/2 pica
art:0000498-D
The lug nuts on the wheel
*
[ER08800(ALL)03/96]7.
Place any wheel covers and ornaments in the trunk.
*
[ER08900(ALL)03/96]8.
Put the tire, jack, and wrench away. Make sure the jack is
securely fastened so it does not rattle when you drive.
*
[ER09000(ALL)03/96]9.
Unblock the wheels.
[ER09100(ALL)12/95]
Removing and Replacing Styled Polycast Wheel
Ornaments
[ER09200(ALL)12/95]
To remove a wheel ornament, insert the tapered end of the jack
handle between the ornament and wheel and pry the ornament
from the wheel.
[ER09300(ALL)12/95]
To install the polycast wheel center ornament, you should insert
one side of the ornament into the center of the wheel opening
and strike the opposite side with the palm of your hand until
the ornament is seated in the opening.
File:10cdero.ex
Update:Thu Sep 12 11:06:09 1996