1997 FORD ASPIRE jump cable

139 %
*
[ER12275(ALL)02/96]
WARNING
Applying too much pressure on the ends
when lifting a battery could cause acid to
spill. Lift the battery with a carrier or
with your hands on the opposite corners.
%*
[ER12280(ALL)02/96]
WARNING
Batteries contain sulfuric acid which burns
skin, eyes, and clothing.
*
[ER12285(ALL)02/96]
If the acid touches someone's skin, eyes, or
clothing, immediately flush the area with water
for at least 15 minutes. If someone swallows the
acid, have him or her drink lots of milk or water
first, then Milk of Magnesia, a beaten egg, or
vegetable oil. Call a doctor immediately.
*
[ER12290(ALL)01/96]
WARNING
Do not push-start your vehicle. You could
damage the catalytic converter. For further
information, seeJumper Cablesin the
Index.
*
[ER12295(ALL)02/96]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
%*
[ER12300(ALL)02/96]
Preparing Your Vehicle
*
[ER12305(ALL)02/96]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

140
*
[ER12310(ALL)02/96]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[ER12315(ALL)02/96]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[ER12320(ALL)02/96]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
*
[ER12325(ALL)03/96]
5. Turn on the heater fan in both vehicles.
Press the DEFROST button. Turn off all
other switches and gauges.
%*
[ER12330(ALL)02/96]
Connecting the jumper cables
*
[ER12335(ALL)02/96]
1. Connect one end of the first jumper cable to
the positive (+) terminal of the discharged
battery. (You can connect either jumper cable
to the positive (+) terminal, as long as you
use the same cable for both positive
terminals.) Most jumper cables have a red
cable and a black cable. The red cable is
generally used for the positive terminals and
the black for the negative ones.
*
[ER12340(ALL)02/96]
2. Connect the other end of the first cable to
the positive (+) terminal of the booster
battery.
*
[ER12345(ALL)02/96]
3. Connect one end of the second cable to the
negative (S) terminal of the booster battery
Ð NOT to the discharged battery.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

141
*
[ER12350(ALL)01/96]
4. Connect the other end of that cable to a
good metallic surface on the engine or frame
of the disabled vehicle. The following
illustration shows where you can find a
metallic surface.
*
[ER12355(ALL)02/96]
WARNING
Do not connect the end of the second
cable to the negative (S) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
[ER12360(ALL)04/96]
half page art:0032286-A
The sequence for connecting the jumper cables
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

142
*
[ER12365(ALL)02/96]
Jump-Starting
*
[ER12370(ALL)02/96]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[ER12375(ALL)02/96]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[ER12380(ALL)02/96]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
%*
[ER12385(ALL)02/96]
Removing jumper cables
*
[ER12390(ALL)02/96]
1.Always remove the jumper cables in the
reverse order.Remove the negative (S) end
of the jumper cable from the metallic surface
on the engine or frame of the disabled
vehicle.
*
[ER12395(ALL)03/96]
2. Remove the negative (S) cable from the
booster battery.
*
[ER12400(ALL)02/96]
3. Remove the positive (+) cable from the
booster battery.
*
[ER12405(ALL)02/96]
4. Remove the other end of the positive (+)
cable from the discharged battery.
*
[ER12410(ALL)02/96]
After the vehicle is started, let it idle for a while
to let the engine ªrelearnº its idle conditions.
Drive it around for a while with all electrical
accessories turned off to let the battery recharge.
Driveability may be deteriorated slightly until all
drive modes are ªrelearned.ºYou may need to
use a battery charger to fully recharge the
battery.
*
[ER12415(ALL)03/96]
If you need to replace your battery, seeBattery
in theMaintenance and Carechapter.
File:10icerf.ex
Update:Tue Mar 4 08:55:59 1997

252 Index
J
Jack.................. 132
operation.............133, 136
positioning............133, 136
storage................ 132
Jump-starting your vehicle
attaching cables............ 140
disconnecting cables.......... 142
K
Keys
key in ignition chime.......... 16
positions of the ignition......... 44
stuck in lock position.......... 44
L
Lamps
checking............... 184
daytime running light system...... 46
dome lamps.............. 41
flashing the lamps............ 47
hazard flashers.......... 45,121
high-mount brakelamp........ 191
instrument panel, dimming....... 41
interior lamps.............. 41
replacing bulbs............ 184
Lane change indicator (see Turn signal) . 45, 48
Lights, warning and indicator
airbag................. 14
anti-lock brakes (ABS).......... 15
brake................. 9
charging system............. 11
check engine.............. 13
engine oil pressure........... 11
hazard warning light....... 45,121
high beam............... 12
lowoil................. 11
oil pressure............... 11
safety belt............... 9
File:icixf.ex
Update:Tue Mar 4 08:59:36 1997