1997 FORD AEROSTAR child lock

100 [SS00225(ALL)04/96]To install the rear bucket seat:
[SS00230(ALL)01/96]
1. Lift the seat assembly into the vehicle and
drop the front and rear floor hooks into the
floor wells at a point just behind the floor
attachment pins.
[SS00235(ALL)01/96]
2. Rotate the seat latch handle forward, causing
the J hook to engage over the front of the
foremost well retainer.
[SS00240(ALL)01/96]
3. For right hand seats, continue rotating the
seat latch handle until it comes to a
complete stop on the top of the tube. This
will cause the seat assembly to slide forward,
engaging the front and rear floor hooks with
the floor well retainers.
[SS00245(ALL)01/96]
For left hand seats, push the seat latch
handle downward to a full stop. This locks
the seat in position. Before you engage the
safety belt, be sure it is not twisted. Remove
any twist, then insert the tongue end of the
detachable anchor into the detachable anchor
until you hear a ªsnapº and feel the latch
engage.
*
[SS00250(ALL)02/96]
RWARNING
Check to see that the seat and seatback
are latched securely in position. Keep
floor area free of objects that would
prevent proper seat engagement. Never
attempt to adjust the seat while the
vehicle is in motion.
[SS00255(ALL)05/96]
Two and Three Passenger Bench Seats and
Seat Bed Assemblies (If Equipped)
[SS00260(ALL)01/96]
NOTE: If your vehicle is equipped with a
Built-In Child Seat, make sure the
child seat is properly stowed before
operating the seat bed.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

110
*
[SS02700(ALL)02/96]
RWARNING
Never let a passenger hold a child on his
or her lap while the vehicle is moving.
The passenger cannot protect the child
from injury in a collision.
*
[SS02900(ALL)02/96]
RWARNING
Lock the doors of your vehicle before
driving to lessen the risk of the door
coming open in a collision.
%
*
[SS03000(ALL)02/96]
Combination Lap and Shoulder
Belts
*
[SS03200(ALL)02/96]
While your vehicle is in motion, the combination
lap and shoulder belt adjusts to your movement.
However, if you brake hard, turn hard, or if
your vehicle receives an impact of 5 mph
(8 km/h) or more, the lap/shoulder belt locks
and helps reduce your forward movement.
*
[SS03400(ALL)01/96]
After you get into your vehicle, close the door
and lock it. Then adjust the seat to the position
that suits you best.
*
[SS03500(ALL)02/96]
Pull the combination lap/shoulder belt from the
retractor so that the shoulder portion of the belt
crosses your shoulder and chest. Be sure the belt
is not twisted. If it is, remove the twist. Insert
the belt tongue into the proper buckle until you
hear a snap and feel it latch. Make sure the
tongue is securely fastened to the buckle by
pulling on tongue.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

112
*
[SS04220(ALL)02/96]
Dual locking mode retractors operate in two
ways:
*
[SS04230(ALL)02/96]
Vehicle sensitive (emergency) locking mode
*
[SS04240(ALL)02/96]
In this operating mode, the shoulder belt
retractor will allow the occupant freedom of
movement, locking tight only on hard braking,
hard cornering or impacts of approximately
5 mph (8 km/h) or more. The retractor can also
be made to lock by pulling the belt out quickly.
%*
[SS04250(ALL)02/96]
Automatic locking mode
*
[SS04260(ALL)01/96]
In this operating mode, the shoulder belt
retractor will be automatically locked and will
remain locked when the combination
lap/shoulder safety belt is buckled, and does not
allow the occupant freedom of movement. This
mode provides the following:
*
[SS04270(ALL)01/96]
q
A tight lap/shoulder belt on the occupant.
*
[SS04280(ALL)01/96]
q
Child safety seat installation.
*
[SS04300(ALL)01/96]
This modemust be usedwhen installing a child
safety seat on the front passenger seat and rear
outboard seats where dual locking retractors are
provided.
*
[SS04310(ALL)01/96]
To switch the retractor from the emergency
locking mode to the automatic locking mode,
perform the following steps:
*
[SS04320(ALL)02/96]
1. Buckle the lap/shoulder combination belt.
*
[SS04330(ALL)01/96]
2. Grasp the shoulder portion of the belt and
pull downward until all of the belt is
extracted and, when allowed to retract, a
clicking sound is heard. At this time, the belt
retractor is in the automatic locking mode
(child restraint mode).
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

113
*
[SS04340(ALL)02/96]
3. A clicking sound will continue to be heard
as the belt is allowed to retract. This
indicates that the retractor is in the
automatic locking mode.
*
[SS04350(ALL)02/96]
NOTE: When the combination lap/shoulder
belt is unbuckled and allowed to
retract completely, the retractor will
switch to the vehicle sensitive
(emergency) locking mode. See the
detailed instructions underSafety Seats
for Childrenin this chapter.
[SS04375(ALL)01/96]
Two Passenger Bench or Bedseat
(If Equipped)
[SS04400(ALL)04/96]
In addition to anchorages in the floor and roof
structures, some rear safety belts have a
detachable anchor mounted to the outboard side
of the rear seats. This should remain attached,
except when removing the rear seats.
[SS04800(ALL)01/96]
Disengaging rear seat safety belts for seat
removal
[SS04850(ALL)01/96]
In order to remove the rear seat, the safety belt
must be disengaged from the seat. To disengage
the safety belt from the seat, insert a key or
small screwdriver into the slot provided on the
detachable anchor. Then lift upward.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

130 %
*
[SS15900(ALL)01/96]
Safety Seats for Children
*
[SS16000(ALL)01/96]
Use a safety seat that is recommended for the
size and weight of the child. Always follow the
safety seat manufacturer's instructions when
installing and using the safety seat.
[SS16005(ALL)01/96]
Most child safety seats can be used in this
vehicle only in vehicle seating positions with
lap/shoulder belts. Any booster-type seat that
places the vehicle's lap belt or shoulder belt
around a shield above and ahead of the child's
hips should not be used in this vehicle. This
type of safety seat could cause injury by tipping
over the front edge of the vehicle seat during a
collision.
[SS16010(ALL)04/96]
RWARNING
The following instructions MUST BE
FOLLOWED to reduce risk of injury from
a safety seat tipping too far forward in a
severe crash.
[SS16012(ALL)01/96]
Install forward-facing child safety seats only in
vehicle seating positions equipped with
lap/shoulder belts. Forward-facing convertible
safety seats can be used in the center of the
three-passenger second row bench seat only if a
top tether strap is used. Ford recommends
placing forward-facing safety seats in the second
row and using safetey seats with top tether
straps for added protection.
[SS16015(ALL)01/96]
For more information on top tether straps see
Attaching Safety Seats With Tether Strapsin this
chapter.
*
[SS16025(ALL)05/96]
When installing a child safety seat, be sure to
use the correct safety belt buckle for that seating
position, and make sure the tongue is securely
fastened in the buckle. For a shoulder/lap belt
combination with a sliding tongue, make sure
the retractor is in the automatic locking mode.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

131
*
[SS16090(ALL)05/96]
All child restraint systems are designed to be
secured in vehicle seats by lap belts or by the
lap portion of a lap-shoulder belt.
*
[SS16100(ALL)03/96]
RWARNING
If you do not properly secure the safety
seat, the child occupying the seat may be
injured during a collision or sudden stop.
An unsecured safety seat could also injure
other passengers.
*
[SS16125(ALL)03/96]
RWARNING
Carefully follow all of the manufacturer's
instructions included with the safety seat
you put in your vehicle. If you do not
install and use the safety seat properly,
the child may be injured in a sudden stop
or collision.
[SS25601(ALL)01/96]
Installing Child Safety Seats in
the Front Seat and Rear Outboard
Seating Positions
[SS25650(ALL)01/96]
Your vehicle is equipped with a dual locking
mode retractor on the shoulder belt portion of
the combination lap/shoulder safety belt for the
right front seat passenger and rear outboard
passengers.
[SS25701(ALL)01/96]
If you choose to install a child safety seat or
infant carrier in these seating positions:
[SS25750(ALL)01/96]
1. Position the child seat on the seat of the
vehicle. In the front seat, adjust the vehicle
seat as far rearward as possible.
[SS25801(ALL)01/96]
2. Pull down on the shoulder belt, then grasp
the shoulder belt and lap belt together. See
Figure 1.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

134
*
[SS26301(ALL)01/96]
4. Grasp the shoulder portion of the belt and
pull downward until all of the belt is
extracted and a click is heard. At this time,
the retractor is in the automatic locking
mode (child seat restraint mode). See
Figure 4.
[SS26401(ALL)01/96]
half page art:0011241-A
Setting the retractor to automatic locking mode
*
[SS26500(ALL)02/96]
5. Allow the belt to retract. Pull up on the
shoulder webbing. A clicking sound will be
heard as the belt retracts. This indicates the
retractor is in the automatic locking mode.
Push down on the child seat while you pull
up on the belt to remove any slack in the
belt. See Figures 5 and 6.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

136
*
[SS26801(ALL)02/96]
6. Before placing the child in the child seat,
forcibly tilt the seat from side to side, and
tug it forward to make sure that the seat is
securely held in place. See Figure 7.
[SS26900(ALL)01/96]
half page art:0011244-A
Checking that the seat is secure
*
[SS27000(ALL)02/96]
7. Double check that the retractor is in the
automatic locking mode. Try to pull more
belt out of the retractor. If you cannot, the
belt is in the automatic locking mode. See
Figure 8.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996