1997 FORD AEROSTAR ECO mode

225
*
[ER24600(ALL)02/96]
RWARNING
Do not connect the end of the second
cable to the negative (S) terminal of the
battery to be jumped. A spark may cause
an explosion of the gases that surround
the battery.
[ER24610(ALL)01/96]
one third page art:0095070-A
Attaching jumper cables
*
[ER24620(ALL)02/96]
Jump-Starting
*
[ER24630(ALL)02/96]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[ER24640(ALL)02/96]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[ER24650(ALL)02/96]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

226 %
*
[ER24660(ALL)02/96]
Removing jumper cables
*
[ER24670(ALL)02/96]
1.Always remove the jumper cables in the
reverse order.Remove the negative (S) end
of the jumper cable from the metallic surface
on the engine or frame of the disabled
vehicle.
*
[ER24680(ALL)03/96]
2. Remove the negative (S) cable from the
booster battery.
*
[ER24690(ALL)02/96]
3. Remove the positive (+) cable from the
booster battery.
*
[ER24692(ALL)02/96]
4. Remove the other end of the positive (+)
cable from the discharged battery.
*
[ER24694(ALL)02/96]
After the vehicle is started, let it idle for a while
to let the engine ªrelearnº its idle conditions.
Drive it around for a while with all electrical
accessories turned off to let the battery recharge.
Driveability may be deteriorated slightly until all
drive modes are ªrelearned.ºYou may need to
use a battery charger to fully recharge the
battery.
*
[ER24695(ALL)03/96]
If you need to replace your battery, seeBattery
in theMaintenance and Carechapter.
%
*
[ER24700(ALL)04/96]
Towing Your Vehicle
[ER24750(ALL)01/96]
The recommended method to tow your Aerostar
is with flatbed or wheel lift equipment.
However, slingbelt towing is acceptable. On
vehicles equipped with an under-vehicle spare
tire carrier, remove the tire assembly from the
carrier and store it in a secure area before
towing. For E-4WD vehicles, the 4-wheel drive
system must be disabled prior to towing. The
transmission must be in N (Neutral) and the
ignition switch must be in the OFF position to
disable the Electronic 4-Wheel Drive System.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

267
*
[MC36800(ALL)01/96]
To fill the fuel tank properly:
*
[MC36900(ALL)01/96]
NOTE: Extinguish all lit cigarettes, other
smoking materials, and any open
flames before fueling your vehicle.
*
[MC37000(ALL)01/96]
1. Remove the fuel cap by following the
instructions above underRemoving the Fuel
Capin this chapter. Proceed to add fuel to
the tank only if your vehicle is on level
ground.
*
[MC37010(ALL)01/96]
2. Make sure that you pump unleaded fuel and
put the nozzle all the way inside the fuel
filler pipe.
*
[MC37020(ALL)01/96]
3. If you spill any fuel on the body of your
vehicle, clean it off immediately. The fuel
may dull or soften the paint if you do not
wash it off.
[MC37030(ALL)05/96]
4. Replace the fuel cap completely when you
are finished. Turn it clockwise until it is fully
tight. It will click when it is fully tightened.
*
[MC37040(ALL)01/96]
You may occasionally hear and/or feel a slight
thump occurring one or two seconds after a
gentle stop. This is normal and generally occurs
with the fuel tank 3/4 full. It is caused by the
wave action of the fuel within the tank.
%*
[MC37050(ALL)01/96]
Running Out of Fuel
*
[MC37060(ALL)01/96]
If your vehicle runs out of fuel, try to stop on
level ground away from traffic. Add at least two
gallons (8 liters) of fuel to start your vehicle
again. If your vehicle is not on level ground,
you may need as much as five gallons (20 liters)
of fuel to start it.
*
[MC37070(ALL)08/95]
NOTE: Avoid running out of fuel because this
situation may have an adverse effect on
modern powertrain components.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

271
*
[MC38440(ALL)01/96]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[MC38450(ALL)01/96]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
%*
[MC38500(ALL)03/96]
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
*
[MC38510(ALL)05/96]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If the
vehicle's powertrain system or its battery has
just been serviced, the OBD II system is reset to
a not ready for I/M testing condition. To
prepare for I/M testing, the law specifies that
additional mixed city and highway driving is
required to complete the check of the OBD II
system.
*
[MC38520(ALL)05/96]
The driving modes required to reach the ready
condition consist of a minimum of 30 minutes of
city and highway driving as described below:
*
[MC38525(ALL)03/96]
q
20 minutes of driving in stop and go
city-type traffic with at least four idle periods.
*
[MC38535(ALL)03/96]
q
10 minutes of driving on an expressway or
highway.
*
[MC38545(ALL)05/96]
Before completing the above driving modes, the
engine must be warmed up and at operating
temperature. Once started, the vehicle must not
be turned off during the above driving modes. If
the vehicle owner is unable to meet the I/M
requirements by using these driving patterns, an
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996