1997 FORD AEROSTAR warning

90 [CF31600(ALL)05/96]
one third page art:0020207-EOpening the sliding side window
%*
[CF31700(ALL)01/96]
Using the Power Windows (If equipped)
[CF31800(ALL)01/96]
Each front door has a power control that opens
and closes the window on that door. The
driver's door has a master control switch that
operates both front door windows. You must
place the ignition switch in the ON or ACC
position to use your power window controls.
*
[CF31900(ALL)01/96]
RWARNING
Make sure that the liftgate door and/or
window are closed to prevent exhaust
fumes from being drawn into the vehicle.
This will also prevent passengers and
cargo from falling out. If you must drive
with the liftgate door or window open,
keep the vents open so outside air comes
into the vehicle.
*
[CF32000(ALL)01/96]
RWARNING
Do not let children play with the power
windows.
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996

91 [CF32100(ALL)01/96]
quarter page art:0020201-C
Power window controls Ð driver-side shown
%*
[CF50000(ALL)03/96]
Mirrors
[CF54100(ALL)01/96]
For vehicles without rear door windows, the
right-hand side mirror is a flat glass mirror. All
other vehicles have convex right-hand side view
mirrors. Convex mirrors have a curved surface
and will show a wider view of the lane next to
and behind your vehicle.
*
[CF54400(ALL)05/96]
RWARNING
The right side view mirror makes objects
appear smaller and farther away than they
actually are.
%*
[CF54500(ALL)05/96]
Dual Electric Remote Control Mirrors
(If equipped)
*
[CF54600(ALL)05/96]
To adjust the remote controlled side mirrors:
[CF54700(ALL)01/96]
1. Locate the switch in the driver's door trim
panel.
[CF54900(ALL)01/96]
2. Select the right or left mirror by moving the
center switch to the left-hand or right-hand
position. The midway position moves neither
the left-hand or right-hand mirror.
[CF55100(ALL)01/96]
3. Press the appropriate side of the square
marked by an arrow indicating the direction
of adjustment.
File:05cpcfa.ex
Update:Mon Jun 24 08:10:35 1996

97
Seating and Safety
Restraints
%*
[SS00102(ALL)05/96]
Seats
%*
[SS00105(ALL)01/96]
Adjusting the Front Seat Manually
[SS00110(ALL)01/96]
You can move the driver seat forward or
backward. If your vehicle is equipped with the
optional reclining bucket seat, you can also tilt
the seatback up to 30 degrees rearward.
[SS00115(ALL)01/96]
The front passenger seat cannot be adjusted.
[SS00120(ALL)01/96]
one third page art:0095010-B
Seat adjustment levers
*
[SS00125(ALL)05/96]
RWARNING
Never adjust the driver's seat or seatback
when the vehicle is moving.
*
[SS00130(ALL)05/96]
RWARNING
Do not pile cargo higher than the
seatbacks to avoid injuring people in a
collision or sudden stop.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

98
*
[SS00135(ALL)02/96]
RWARNING
Always drive and ride with your seatback
upright and the lap belt snug and low
across the hips.
*
[SS00140(ALL)02/96]
RWARNING
Children should always ride with the
seatback in the fully upright position.
*
[SS00145(ALL)08/95]
To move the seat forward or backward:
[SS00150(ALL)01/96]
one third page art:0095011-B*
[SS00155(ALL)08/95]
To recline the seatback:
[SS00160(ALL)01/96]
one third page art:0095012-BFile:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

100 [SS00225(ALL)04/96]To install the rear bucket seat:
[SS00230(ALL)01/96]
1. Lift the seat assembly into the vehicle and
drop the front and rear floor hooks into the
floor wells at a point just behind the floor
attachment pins.
[SS00235(ALL)01/96]
2. Rotate the seat latch handle forward, causing
the J hook to engage over the front of the
foremost well retainer.
[SS00240(ALL)01/96]
3. For right hand seats, continue rotating the
seat latch handle until it comes to a
complete stop on the top of the tube. This
will cause the seat assembly to slide forward,
engaging the front and rear floor hooks with
the floor well retainers.
[SS00245(ALL)01/96]
For left hand seats, push the seat latch
handle downward to a full stop. This locks
the seat in position. Before you engage the
safety belt, be sure it is not twisted. Remove
any twist, then insert the tongue end of the
detachable anchor into the detachable anchor
until you hear a ªsnapº and feel the latch
engage.
*
[SS00250(ALL)02/96]
RWARNING
Check to see that the seat and seatback
are latched securely in position. Keep
floor area free of objects that would
prevent proper seat engagement. Never
attempt to adjust the seat while the
vehicle is in motion.
[SS00255(ALL)05/96]
Two and Three Passenger Bench Seats and
Seat Bed Assemblies (If Equipped)
[SS00260(ALL)01/96]
NOTE: If your vehicle is equipped with a
Built-In Child Seat, make sure the
child seat is properly stowed before
operating the seat bed.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

101
*
[SS00265(ALL)01/96]
To remove seat assembly:
[SS00270(ALL)04/96]
1. Disengage the lap/shoulder safety belt from
the seat by inserting a key or screwdriver
into the slot in the detachable anchor and
lifting upward. Stow the tongue end of the
detachable anchor as shown in the
illustration.
[SS00275(ALL)01/96]
three fourths page art:0095047-A
Location of the detachable anchor warning label on safety
belt
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

103
*
[SS00295(ALL)01/96]
RWARNING
When reinstalling a rear seat in your
vehicle it must be placed in its original
position. Improper installation of the seat
will prevent correct use of the safety belts
and could increase the risk of injury.
Refer to the warning label on the seat
belt.
[SS00300(ALL)01/96]
2. Fold the seatback forward and latch it in the
down position (bench seat only).
[SS00305(ALL)01/96]
3. Rotate the seat latch handles (located under
the seat near the floor) upward, causing the
latch hooks to disengage from the floor
attachment.
[SS00310(ALL)01/96]
4. Lift seat at rear and rotate about the forward
attachment. When seat latches are clear of
floor attachments, release the latch handles.
[SS00315(ALL)01/96]
5. Pull the seat rearward to disengage it from
the front floor pins.
*
[SS00320(ALL)01/96]
Be careful that the latches are not damaged
when the seats are stored.
*
[SS00325(ALL)01/96]
To install the seat assembly:
*
[SS00330(ALL)01/96]
1. Clear the area of debris around the seat floor
attachments.
[SS00335(ALL)01/96]
2. With the seatback in a folded and latched
position (bench seat only), place the seat
assembly in your vehicle and engage the
front seat hooks onto the forward attachment
pin in the floor wells.
*
[SS00340(ALL)01/96]
3. Rotate the seat downward and engage the
latch into the rear floor attachment. Lifting
of the latch handles is not required for
installation.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996

105 [SS00375(ALL)01/96]
half page art:0095041-A
Installation and removal of the second and third passenger
bed and bench seat
*
[SS00380(ALL)05/96]
RWARNING
Never adjust the driver's seat or seatback
when the vehicle is moving.
*
[SS00385(ALL)01/96]
RWARNING
Always latch the vehicle seat to the floor,
whether the seat is occupied or empty. If
not latched, the seat may cause injury
during a sudden stop.
*
[SS00390(ALL)01/96]
RWARNING
Before using the seat, make sure that the
latch hooks are securely locked around the
floor pins.
File:06cpssa.ex
Update:Thu Jun 13 08:56:07 1996