Page 54 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 51
*
[AS07035(ALL)06/96]
1. Select a band, then select a frequency.
*
[AS07037(ALL)06/96]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now hel FORD AEROSTAR 1997 1.G Owners Manual 51
*
[AS07035(ALL)06/96]
1. Select a band, then select a frequency.
*
[AS07037(ALL)06/96]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now hel](/manual-img/11/4752/w960_4752-53.png)
51
*
[AS07035(ALL)06/96]
1. Select a band, then select a frequency.
*
[AS07037(ALL)06/96]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS07040(ALL)06/96]
3. Follow the two steps above for each station
memory preset button you want to set.
*
[AS07045(ALL)06/96]
NOTE: If the vehicle's battery is disconnected,
the clock and station memory preset
buttons (if programmed in auto mode)
will need to be reset.
[AS07050(ALL)05/96]
Using the Controls of Your Cassette Tape
Player (If equipped)
*
[AS07075(ALL)08/95]
How to insert a tape
*
[AS07100(ALL)08/95]
Insert a cassette (with the open edge to the
right) firmly into the tape door opening, making
sure the cassette is completely in and ªseated.º
*
[AS07125(ALL)08/95]
NOTE: A cassette tape can be loaded with the
ignition on whether or not the radio
power is on.
*
[AS07150(ALL)12/95]
How to locate a desired track on the tape
*
[AS07175(ALL)08/95]
q
Using the Automatic Music Search (ªAMSº)
[AS07200(ALL)09/95]
Press and hold the ªAMSº button (ªAMSº
will appear in the display). Then, push the
left (
h) button to rewind to the beginning
of the current selection or press the right
(
g) button to fast forward to the beginning
of the next selection.
*
[AS07225(ALL)08/95]
q
How to change the side of the tape being
played
[AS07250(ALL)09/95]
The alternate track (other side) of the tape
can be selected at any time by pushing both
fast-wind buttons (
hand
g) at the
same time.
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996
Page 57 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 54
*
[AS07730(ALL)08/95]
Rear Seat Radio Controls
*
[AS07735(ALL)08/95]
Using the Rear Seat Radio Controls
[AS07740(ALL)05/96]
Rear seat radio controls are available on some
Aerostar models.
[AS07745( FORD AEROSTAR 1997 1.G Owners Manual 54
*
[AS07730(ALL)08/95]
Rear Seat Radio Controls
*
[AS07735(ALL)08/95]
Using the Rear Seat Radio Controls
[AS07740(ALL)05/96]
Rear seat radio controls are available on some
Aerostar models.
[AS07745(](/manual-img/11/4752/w960_4752-56.png)
54
*
[AS07730(ALL)08/95]
Rear Seat Radio Controls
*
[AS07735(ALL)08/95]
Using the Rear Seat Radio Controls
[AS07740(ALL)05/96]
Rear seat radio controls are available on some
Aerostar models.
[AS07745(ALL)08/95]
The rear seat radio controls are located behind
the driver on the left hand side of the vehicle.
These controls duplicate several radio functions
of the radio and allow the use of headphones in
the vehicle.
[AS07750(ALL)10/95]
one third page art:0060647-B
Rear seat radio controls
*
[AS07755(ALL)06/95]
How to turn the rear seat radio controls on
and off
[AS07760(ALL)08/95]
Press memory preset buttons ª1º and ª3º
simultaneously on the face of your radio to turn
the rear seat radio controls on. A headphones
symbol (j) will appear in the display when the
rear seat controls are on. Press ª1º and ª3º
simultaneously again to turn the rear seat radio
controls off.
*
[AS07765(ALL)03/96]
How to adjust the volume
[AS07770(ALL)08/95]
Press the right (+) side of the ªVOLUMEº rocker
switch to increase volume; and push the left (S)
side to decrease the volume of the rear speakers.
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996
Page 58 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 55 [AS07775(ALL)08/95]
NOTE: Rear seat control volume can be set no
higher than current radio setting unless
speakers are turned off. See note under
How to turn the speakers on and off.
*
[AS07780(ALL FORD AEROSTAR 1997 1.G Owners Manual 55 [AS07775(ALL)08/95]
NOTE: Rear seat control volume can be set no
higher than current radio setting unless
speakers are turned off. See note under
How to turn the speakers on and off.
*
[AS07780(ALL](/manual-img/11/4752/w960_4752-57.png)
55 [AS07775(ALL)08/95]
NOTE: Rear seat control volume can be set no
higher than current radio setting unless
speakers are turned off. See note under
How to turn the speakers on and off.
*
[AS07780(ALL)06/95]
Setting the AM or FM frequency band
*
[AS07785(ALL)06/95]
Push the ªBANDº button to change the
frequency band.
*
[AS07790(ALL)06/95]
Using the ªMEMORYº button
*
[AS07795(ALL)06/95]
Push the ªMEMORYº button to access the
station you have set into memory button 1 on
the face of the radio. Successively pushing this
button will access, numerically, all stations set
into the Station Memory Preset buttons (1
through 5).
*
[AS07800(ALL)06/95]
How to turn the speakers on and off
*
[AS07805(ALL)06/95]
When the rear seat controls are on, push the
ªSPKRS ON-OFFº button to turn all speakers
off. Push again to turn all speakers on.
[AS07810(ALL)09/95]
NOTE: Turning the ignition off then on again
will not turn the speakers back on, if
previously turned off by the ªSPKRS
ON-OFFº button on the rear seat
controls.
*
[AS07815(ALL)06/95]
Using the ªSEEKº function
[AS07820(ALL)08/95]
Press the right (
a) side of the ªSEEKº rocker
switch to seek to the next radio station. Press the
left (
b) side of the ªSEEKº rocker switch to
seek to the previous radio station.
*
[AS07825(ALL)09/95]
NOTE: When using the rear seat controls with
a High-Level Audio System, the
ªSEEKº function on the rear seat
controls will also function with
cassettes, seeking the next (ªSEEK
aº)
or previous (ª
bSEEKº) selection on
the tape.
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996
Page 157 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 156
*
[TO06800(ALL)01/96]
If the engine still does not start after two
attempts:
*
[TO06825(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO06851(ALL)01/96]
2. Press the accelerator all FORD AEROSTAR 1997 1.G Owners Manual 156
*
[TO06800(ALL)01/96]
If the engine still does not start after two
attempts:
*
[TO06825(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO06851(ALL)01/96]
2. Press the accelerator all](/manual-img/11/4752/w960_4752-156.png)
156
*
[TO06800(ALL)01/96]
If the engine still does not start after two
attempts:
*
[TO06825(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO06851(ALL)01/96]
2. Press the accelerator all the way to the floor
and hold it.
*
[TO06876(ALL)01/96]
3. Turn the ignition key to the START position.
*
[TO06900(ALL)01/96]
4. Release the ignition key when the engine
starts.
*
[TO06925(ALL)03/96]
5. Release the accelerator gradually as the
engine speeds up.
*
[TO06951(ALL)05/96]
If the engine still does not start, the fuel pump
shut-off switch may have been activated. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchin the index.
%*
[TO07300(ALL)01/96]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
*
[TO07390(ALL)01/96]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
*
[TO07400(ALL)01/96]
RWARNING
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the
risk of fire or other damage.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 159 of 347
158
%*
[TO08500(ALL)01/96]
If the Engine Cranks but Does
Not Start or Does Not Start After
a Collision
%*
[TO08510(ALL)01/96]
Fuel Pump Shut-Off Switch
[TO08520(ALL)03/96]
If the engine cranks but does not start or does
not start even after a small collision, the fuel
pump shut-off switch may have been activated.
The shut-off switch is a device intended to stop
the fuel pump when your vehicle has been
involved in a substantial jolt. Refer to the
Roadside Emergencieschapter.
*
[TO08530(ALL)03/96]
Once the shut-off switch is activated, you must
reset the switch by hand before you can start
your vehicle.
[TO08540(ALL)01/96]
one third page art:0095071-A
Fuel pump shut-off switch location
*
[TO08550(ALL)03/96]
RWARNING
If you see or smell fuel, do not reset the
switch or try to start your vehicle. Have
all the passengers get out of the vehicle
and call the local fire department or a
towing service.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 160 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 159
*
[TO08560(ALL)03/96]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[TO08570(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO08580(ALL)03/96]
2. C FORD AEROSTAR 1997 1.G Owners Manual 159
*
[TO08560(ALL)03/96]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[TO08570(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO08580(ALL)03/96]
2. C](/manual-img/11/4752/w960_4752-159.png)
159
*
[TO08560(ALL)03/96]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[TO08570(ALL)01/96]
1. Turn the ignition key to the OFF position.
*
[TO08580(ALL)03/96]
2. Check under the vehicle for leaking fuel.
*
[TO08590(ALL)01/96]
3. If you do not see or smell fuel, push the red
reset button down. If the button is already
set, you may have a different mechanical
problem.
*
[TO08600(ALL)01/96]
4. Turn the ignition key to the ON position for
a few seconds, then turn it to the OFF
position.
*
[TO08610(ALL)03/96]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[TO08620(ALL)01/96]
6. Check all vehicle warning lights before
driving the vehicle.
[TO08630(ALL)04/96]
quarter page art:0020107-A
Reset button for fuel pump shut-off switch
*
[TO09200(ALL)02/96]
RWARNING
Do not start your vehicle in a closed
garage or in other enclosed areas. Exhaust
fumes can be toxic. Always open the
garage door before you start the engine.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996
Page 200 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 200
*
[ER00200(ALL)05/96]
If the Engine Cranks But Does
Not Start or Does Not Start After
a Collision
*
[ER00250(ALL)05/96]
The Fuel Pump Shut-off Switch
*
[ER00260(ALL)05/96]
If the engine cranks but FORD AEROSTAR 1997 1.G Owners Manual 200
*
[ER00200(ALL)05/96]
If the Engine Cranks But Does
Not Start or Does Not Start After
a Collision
*
[ER00250(ALL)05/96]
The Fuel Pump Shut-off Switch
*
[ER00260(ALL)05/96]
If the engine cranks but](/manual-img/11/4752/w960_4752-199.png)
200
*
[ER00200(ALL)05/96]
If the Engine Cranks But Does
Not Start or Does Not Start After
a Collision
*
[ER00250(ALL)05/96]
The Fuel Pump Shut-off Switch
*
[ER00260(ALL)05/96]
If the engine cranks but does not start or if you
have had a collision, the fuel pump shut-off
switch may have been triggered. The shut-off
switch is a device that stops the fuel pump
when your vehicle has been involved in a
substantial jolt.
*
[ER00275(ALL)05/96]
For information on how to check and reset the
fuel pump shut-off switch, seeFuel pump shut-off
switchin the Index.
%
*
[ER00400(ALL)05/96]
Fuses
*
[ER00410(ALL)01/96]
Fuses and circuit breakers protect your vehicle's
electrical system from overloading. If electrical
parts in your vehicle are not working, the
system may have been overloaded and blown a
fuse or tripped a circuit breaker. Before you
replace or repair any electrical parts, check the
appropriate fuses or circuit breakers.
*
[ER00415(ALL)01/96]
The following charts tell you which fuses or
circuit breakers protect each electrical part of
your vehicle. If a fuse blows or a circuit breaker
opens a circuit, all the parts of your vehicle that
use that circuit will not work.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996
Page 209 of 347
![FORD AEROSTAR 1997 1.G Owners Manual 209 %
*
[ER00510(ALL)05/96]
Circuit Breakers
[ER00515(ALL)01/96]
If you need to check a circuit breaker, locate the
fuse panel first. Otherwise, locate the circuit
breaker according to the instruction FORD AEROSTAR 1997 1.G Owners Manual 209 %
*
[ER00510(ALL)05/96]
Circuit Breakers
[ER00515(ALL)01/96]
If you need to check a circuit breaker, locate the
fuse panel first. Otherwise, locate the circuit
breaker according to the instruction](/manual-img/11/4752/w960_4752-208.png)
209 %
*
[ER00510(ALL)05/96]
Circuit Breakers
[ER00515(ALL)01/96]
If you need to check a circuit breaker, locate the
fuse panel first. Otherwise, locate the circuit
breaker according to the instructions on the
charts given earlier in this chapter.
*
[ER00520(ALL)01/96]
However, you should know that the circuit
breakers will reset themselves and allow the
electrical parts to work again once the overload
on the circuit is removed. If the circuit breakers
continue to cut off electricity, have your vehicle's
electrical system checked.
*
[ER00525(ALL)01/96]
Diagnostic equipment is needed to check circuit
breakers. Refer to the manufacturer's
instructions.
[ER00530(ALL)01/96]
If you replace a circuit breaker, use one with the
same amperage rating. To remove a circuit
breaker, grip it with your finger and thumb and
pull it straight out of its socket.
%
*
[ER03600(ALL)02/96]
Changing a Tire
*
[ER03700(ALL)02/96]
If you get a flat tire while you are driving, do
not apply the brake heavily. Instead, gradually
decrease the speed. Hold the steering wheel
firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off
the ignition, set the parking brake, and turn on
the hazard flashers.
%*
[ER03800(ALL)01/96]
The Conventional Spare Tire
*
[ER03900(ALL)05/96]
If you have the conventional spare tire, you can
use it as a spare or as a regular tire. This spare
tire is identical to the other tires that come with
your vehicle, although the wheel may not match.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996