1997 FORD AEROSTAR change time

50
*
[AS06825(ALL)02/96]
q
Using the ªAMSº function to manually tune
your radio (Stereo Cassette Radio)
[AS06850(ALL)09/95]
You can change the frequency up or down
one increment at a time by first pressing the
ªAMSº button (display shows ªTUNEº) then
within approximately five seconds pressing
and releasing either the right (
a) or left (
b)
side of the ªSEEKº button. To change
frequencies quickly, press andhold down
either the right or left side of the ªSEEKº
button.
*
[AS06875(ALL)04/96]
q
Using the ªSEEKº function
[AS06900(ALL)08/95]
Press the right (
a) side of the ªSEEKº
button to select the next listenable station up
the frequency band. Press the left (
b) side of
the button to select the next listenable station
down the frequency band. By holding the
button down, listenable stations can be
passed over to reach the desired station.
*
[AS07000(ALL)02/96]
q
Using the ªSCANº function (Stereo Cassette
Radio)
*
[AS07025(ALL)02/96]
Press the ªSCANº button to enter the scan
mode. The radio will begin scanning up the
frequency band, stopping on each listenable
station for approximately a five-second
sampling. This continues until you press the
ªSCANº button a second time.
*
[AS07029(ALL)06/96]
q
Setting the Station Memory Preset buttons
%*
[AS07030(ALL)06/96]
Your radio is equipped with 5 station
memory buttons. These buttons can be used
to select up to 5 preset AM stations and 10
FM stations (5 in FM1 and 5 in FM2). Follow
the easy steps below to set these buttons to
the desired frequencies.
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996

51
*
[AS07035(ALL)06/96]
1. Select a band, then select a frequency.
*
[AS07037(ALL)06/96]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS07040(ALL)06/96]
3. Follow the two steps above for each station
memory preset button you want to set.
*
[AS07045(ALL)06/96]
NOTE: If the vehicle's battery is disconnected,
the clock and station memory preset
buttons (if programmed in auto mode)
will need to be reset.
[AS07050(ALL)05/96]
Using the Controls of Your Cassette Tape
Player (If equipped)
*
[AS07075(ALL)08/95]
How to insert a tape
*
[AS07100(ALL)08/95]
Insert a cassette (with the open edge to the
right) firmly into the tape door opening, making
sure the cassette is completely in and ªseated.º
*
[AS07125(ALL)08/95]
NOTE: A cassette tape can be loaded with the
ignition on whether or not the radio
power is on.
*
[AS07150(ALL)12/95]
How to locate a desired track on the tape
*
[AS07175(ALL)08/95]
q
Using the Automatic Music Search (ªAMSº)
[AS07200(ALL)09/95]
Press and hold the ªAMSº button (ªAMSº
will appear in the display). Then, push the
left (
h) button to rewind to the beginning
of the current selection or press the right
(
g) button to fast forward to the beginning
of the next selection.
*
[AS07225(ALL)08/95]
q
How to change the side of the tape being
played
[AS07250(ALL)09/95]
The alternate track (other side) of the tape
can be selected at any time by pushing both
fast-wind buttons (
hand
g) at the
same time.
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996

57
ªshadowº of the structure will allow the station
to return to normal.
*
[AS07900(ALL)05/96]
When the radio waves are reflected off objects or
structures, the reflected signal cancels the normal
signal, causing the antenna to pick up noise and
distortion. Cancellation effects are most
prominent in metropolitan areas, but also can
become quite severe in hilly terrain and
depressed roadways.
*
[AS07905(ALL)05/96]
To minimize these conditions, a stereo/mono
blend circuit has been incorporated into this
system. This feature automatically switches a
weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS07910(ALL)05/96]
Several sources of static are normal conditions
on AM frequencies. These can be caused by
power lines, electric fences, traffic lights and
thunderstorms.
*
[AS07915(ALL)05/96]
Another reception phenomenon isStrong Signal
Capture and Overload. This can occur when
listening to a weak station and when passing
another broadcast tower. The close station may
capture the more distant station, although the
displayed frequency does not change. While
passing the tower, the station may switch back
and forth a few times before returning to the
original station.
*
[AS07920(ALL)05/96]
When several broadcast towers are present
(common in metropolitan areas), several stations
may overload the receiver, resulting in
considerable station changing, mixing and
distortion.
*
[AS07925(ALL)05/96]
Automatic gain control circuitry for both AM
and FM bands has been incorporated into this
system to reduce strong signal capture and
overload.
File:04cpasa.ex
Update:Fri Jun 7 14:24:14 1996

160
*
[TO09300(ALL)12/95]
Guarding Against Exhaust Fumes
*
[TO09400(ALL)01/96]
Carbon monoxide, although colorless and
odorless, is present in exhaust fumes. Take
precautions to avoid its dangerous effects.
*
[TO09600(ALL)01/96]
RWARNING
If you smell exhaust fumes inside your
vehicle, have your dealer inspect your
vehicle immediately. Do not drive if you
smell exhaust fumes.
[TO09700(ALL)04/96]
If your vehicle has rear windows and doors that
were installed as part of a van conversion, close
them while it is running. This prevents exhaust
fumes from being drawn into the passenger
compartment.
*
[TO09900(ALL)01/96]
Have the exhaust and body ventilation systems
checked whenever:
*
[TO10000(ALL)01/96]
q
your vehicle is raised for service
*
[TO10100(ALL)01/96]
q
the sound of the exhaust system changes
*
[TO10200(ALL)01/96]
q
your vehicle has been damaged in a collision
*
[TO10300(ALL)01/96]
Improve your ventilation by keeping all air inlet
vents clear of snow, leaves, and other debris.
*
[TO10400(ALL)01/96]
If the engine is idling while you are stopped in
an open area for long periods of time, open the
windows at least one inch (2.5 cm). Also, adjust
the heating or air conditioning system to bring
in outside air.
*
[TO10600(ALL)01/96]
q
HEATING Ð Set fan speed at MEDIUM or
HIGH, the function selector knob on VENT,
FLOOR, MIX, or the DEFROST symbol and
the temperature control knob on any desired
position.
File:08cptoa.ex
Update:Thu Jun 6 14:43:40 1996

222
*
[ER24200(ALL)01/96]
Also retighten to the specified torque at 500
miles (800 km) of operation after any wheel
change or any time the lug nuts are loosened.
*
[ER24301(ALL)01/96]
RWARNING
Failure to retighten wheel lug nuts at
mileages specified could allow wheels to
come off while the vehicle is in motion.
[ER24315(ALL)01/96]
eight pica chart:0020313-A%*
[ER24400(ALL)02/96]
Jump-Starting Your Vehicle
*
[ER24410(ALL)02/96]
Your vehicle's battery may die if you leave the
lights on or any electrical equipment on after
you turn the engine off. If this happens, you
may be able to jump-start your vehicle with a
booster battery.
*
[ER24420(ALL)02/96]
RWARNING
The gases around the battery can explode
if exposed to flames, sparks, or lit
cigarettes. An explosion could result in
injury or vehicle damage.
*
[ER24430(ALL)02/96]
RWARNING
To protect yourself when charging a
battery, always shield your face and eyes.
Make sure that you can breathe fresh air.
File:10cpera.ex
Update:Thu Jun 6 14:45:00 1996

235 [MC06160(ALL)01/96]
quarter page art:0095016-A
Engine oil dipstick
*
[MC06170(ALL)03/96]
6. Carefully pull the dipstick out again. If the
oil level is below the ªADD 1 QTº line, add
engine oil as necessary. If the oil level is
beyond the letter ªFº in Full, engine damage
or high oil consumption may occur and
some oil must be removed from the engine.
*
[MC06180(ALL)01/96]
7. Put the dipstick back in and make sure it is
fully seated.
%*
[MC06190(ALL)01/96]
Adding engine oil
*
[MC06200(ALL)01/96]
It may be necessary to add some oil between oil
changes. Make sure you use a CERTIFIED
engine oil of the preferred viscosity. Your
vehicle's warranty coverage may not apply if
engine damage is caused by the use of improper
engine oil.
*
[MC06210(ALL)01/96]
Add engine oil through the oil filler cap
highlighted in yellow. To add oil, remove the
filler cap and use a funnel to pour oil into the
opening. Be careful not to overfill the engine.
Recheck the oil level after you finish adding oil.
[MC07000(ALL)05/96]
Engine Oil and Filter Changes
*
[MC07100(ALL)05/96]
Change your engine oil and oil filter according
to these mileage and time requirements,
whichever occurs first.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

246
*
[MC09200(ALL)01/96]
5. If the power steering fluid is low, add fluid
in small amounts, continuously checking the
level, until you reach the FULL HOT range.
Do not overfill.
*
[MC09210(ALL)03/96]
6. When you are finished, put the dipstick back
in and make sure that it fits snugly.
[MC09220(ALL)01/96]
Use only a power steering fluid such as Ford
Power Steering Fluid Motorcraft MERCONH
ATF.
*
[MC09230(ALL)01/96]
If the power steering fluid is low, do not drive
your vehicle for a long period of time before
adding fluid. This can damage the power
steering pump.
*
[MC09240(ALL)03/96]
If you check the power steering fluid when it is
cold, make sure that the fluid reaches the FULL
COLD range on the dipstick. The reading will
only be accurate if the fluid temperature is
approximately 50 to85ÊF (10 to 30ÊC).
*
[MC09250(ALL)01/96]
NOTE: Do not turn the steering wheel of your
vehicle with the engine off. It could
force power steering fluid out from the
reservoir cap or in extreme cases, it
could unseat the cap.
%
*
[MC10000(ALL)01/96]
Automatic Transmission Fluid
*
[MC10100(ALL)05/96]
Under normal driving conditions automatic
transmission fluid should be changed every
30,000 miles (48,000 km) or 21,000 miles
(34,000 km) if under severe duty conditions.
However, if the transmission is not working
properly, for instance, the transmission may slip
or shift slowly, or you may notice some sign of
fluid leakage, the fluid level should be checked.
*
[MC10110(ALL)01/96]
It is preferable to check the transmission fluid
level at normal operating temperature, after
approximately 20 miles (30 km) of driving.
However, if necessary, you can check the fluid
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996

270
*
[MC38250(ALL)01/96]
RWARNING
Do not park, idle, or drive your vehicle in
dry grass or other dry ground cover. The
emission system heats up the engine
compartment and exhaust system, which
can start a fire.
*
[MC38300(ALL)01/96]
RWARNING
On vehicles without original equipment
floor covering or insulation, do not let
passengers ride in your truck in a manner
that allows contact between skin and the
metal floor.
*
[MC38400(ALL)01/96]
Watch for fluid leaks, strange odors, smoke, loss
of oil pressure, the charge warning light, the
check engine light, or the temperature warning
light. These sometimes indicate that the emission
system is not working properly.
*
[MC38410(ALL)01/96]
Do not make any unauthorized changes to your
vehicle or engine. Changes that cause more
unburned fuel to reach the exhaust system can
increase the temperature of the engine or
exhaust system.
*
[MC38420(ALL)01/96]
By law, anyone who manufactures, repairs,
services, sells, leases, trades vehicles, or
supervises a fleet of vehicles is not permitted to
intentionally remove an emission control device
or prevent it from working. In some of the
United States and in Canada, vehicle owners
may be liable if their emission control device is
removed or is prevented from working.
*
[MC38430(ALL)08/95]
Never use a metal exhaust collector when you
service your vehicle. If the metal collector
contacts any of your vehicle's plastic trim or
bumper parts they could melt or deform.
File:11cpmca.ex
Update:Fri Jun 7 14:30:56 1996