Downloaded from www.Manualslib.com manuals search engine (2) Remove 1 inch of insulation from each end of
the wire.
(3) Place a piece of heat shrink tubing over one
side of the wire. Make sure the tubing will be long
enough to cover and seal the entire repair area.
(4) Spread the strands of the wire apart on each
part of the exposed wire (example 1). (Fig. 13)
(5) Push the two ends of wire together until the
strands of wire are close to the insulation (example
2) (Fig. 13)
(6) Twist the wires together (example 3) (Fig. 13)
(7) Solder the connection together using rosin core
type solder only.Do not use acid core solder.
(8) Center the heat shrink tubing over the joint,
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing.
(9) Secure the wire to the existing ones to prevent
chafing or damage to the insulation
(10) Connect battery and test all affected systems.
FUSIBLE LINK REPLACEMENT
On PL vehicles there is a fusible link placed
between the output terminal of the generator and the
engine starter motor terminal. A service part is avail-
able if this fusible link requires replacement.
This service part has the eyelet that attaches to
the starter motor. If the fusible link requires replace-ment this indicates a problem in the charging/start-
ing system that needs to be corrected.
Replacement of the fusible link is the same as
repairing a wire. Refer to the wiring repair informa-
tion in this section for soldering information.
TERMINAL/CONNECTOR REPAIR-MOLEX
CONNECTORS
(1) Disconnect battery.
(2) Disconnect the connector from its mating half/
component.
(3) Insert the terminal releasing special tool 6742
into the terminal end of the connector (Fig. 14).
(4) Using special tool 6742 release the locking fin-
gers on the terminal (Fig. 15).
(5) Pull on the wire to remove it from the connec-
tor.
(6) Repair or replace the connector or terminal, as
necessary.
Fig. 13 Wire Repair
Fig. 14 Molex Connector Repair
Fig. 15 Using Special Tool 6742
8W - 01 - 8 8W - 01 GENERAL INFORMATIONPL
SERVICE PROCEDURES (Continued)
Downloaded from www.Manualslib.com manuals search engine (8) Place a piece of heat shrink tubing over one
side of the wire. Be sure the tubing will be long
enough to cover and seal the entire repair area.
(9) Spread the strands of the wire apart on each
part of the exposed wires.
(10) Push the two ends of wire together until the
strands of wire are close to the insulation.
(11) Twist the wires together.
(12) Solder the connection together using rosin
core type solder only.Do not use acid core solder.
(13) Center the heat shrink tubing over the joint
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing
(14) Repeat steps 8 through 13 for each wire.
(15) Re-tape the wire harness starting 1-1/2 inches
behind the connector and 2 inches past the repair.
(16) Re-connect the repaired connector.
(17) Connect the battery, and test all affected sys-
tems.
TERMINAL REPLACEMENT
(1) Disconnect battery.
(2) Disconnect the connector being repaired from
its mating half. Remove connector locking wedge, if
required (Fig. 20).
(3) Remove connector locking wedge, if required
(Fig. 20).
(4) Position the connector locking finger away from
the terminal using the proper pick from special tool
kit 6680. Pull on the wire to remove the terminal
from the connector (Fig. 21) (Fig. 22).
(5) Cut the wire 6 inches from the back of the con-
nector.
(6) Remove 1 inch of insulation from the wire on
the harness side.
(7) Select a wire from the terminal repair assem-
bly that best matches the color wire being repaired.(8) Cut the repair wire to the proper length and
remove 1 inch of insulation.
(9) Place a piece of heat shrink tubing over one
side of the wire. Make sure the tubing will be long
enough to cover and seal the entire repair area.
(10) Spread the strands of the wire apart on each
part of the exposed wires.
(11) Push the two ends of wire together until the
strands of wire are close to the insulation.
(12) Twist the wires together.
(13) Solder the connection together using rosin
core type solder only.Do not use acid core solder.
(14) Center the heat shrink tubing over the joint
and heat using a heat gun. Heat the joint until the
tubing is tightly sealed and sealant comes out of both
ends of the tubing.
(15) Insert the repaired wire into the connector.
(16) Install the connector locking wedge, if
required, and reconnect the connector to its mating
half/component.
(17) Re-tape the wire harness starting 1-1/2 inches
behind the connector and 2 inches past the repair.
(18) Connect battery, and test all affected systems.
Fig. 20 Connector Locking Wedge Tab (Typical)
Fig. 21 Terminal Removal
Fig. 22 Terminal Removal Using Special Tool
8W - 01 - 10 8W - 01 GENERAL INFORMATIONPL
SERVICE PROCEDURES (Continued)
