1997 DODGE NEON Radio

[x] Cancel search: Radio

tow bar pairing phone carplay door lock coolant reservoir traction control

Load previous 8 pages

Page 141 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 22
PK/RD20 F33
BATT A3
2FUSE15A
1BLOCK
FUSE
4
9
3 OFF
2 PARK
1 HEAD
SWITCH
HEADLAMP
1
2 0
C24
RADIOL7
20
BK/YL
L7 20BK/YL
2C230
1
SWITCH LAMP
F

Page 143 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 8W-50 FRONT LIGHTING
INDEX
page page
GENERAL INFORMATION
INTRODUCTION......................... 7
DESCRIPTION AND OPERATION
FOG LAMPS (FRONT)...

Downloaded from www.Manualslib.com manuals search engine 8W-50 FRONT LIGHTING
INDEX
page page
GENERAL INFORMATION
INTRODUCTION......................... 7
DESCRIPTION AND OPERATION
FOG LAMPS (FRONT).................... 8HEADLAMP LEVELING MOTORS............ 8
HEADLAMPS........................... 7
PARKING LAMPS........................ 7
GENERAL INFORMATION
INTRODUCTION
The headlamp switch has 3 positions, ON, PARK
(parking lights) and OFF. Two circuits, L2 and L20
connect the headlamp switch to the headlamp dim-
mer/optical horn switch located in the multi-function
switch. The multi-function switch feeds the low and
high beams of the headlamps.
DESCRIPTION AND OPERATION
PARKING LAMPS
Circuit A3 in the Power Distribution Center (PDC)
connects to a bus bar in the fuse block. One of the
four circuits powered by the bus bar is circuit F33.
Circuit F33 connects to the headlamp switch. A 40
amp fuse in the PDC protects the A3 circuit. A 15
amp fuse, in cavity 2 of the fuse block, protects the
F33 circuit.
The headlamp switch has 3 positions, ON, PARK
(tail lamps) and OFF, plus a dimmer switch. When
the headlamp switch is in the PARK or ON position,
the switch connects circuit F33 to circuit L7. From
the headlamp switch, circuit L7 branches to power
the front parking lamps and rear tail lamps, lavalier
lamps, side marker lamps, and rear license plate
lamp.
GROUND CIRCUIT
Circuit Z1 provides ground for the parking lamps,
headlamps, lavalier lamps, tail lamps, side marker
lamps and rear license plate lamp although different
grounding points are used. Circuit Z1 also provides
the ground path for the headlamps and turn signals.
HELPFUL INFORMATION
²Check for a blown 40 amp fuse in the PDC.
²Check for a blown fuse in cavity 2 of the fuse
block.
²For the left front parking lamp, turn signal, side
marker lamp and left headlamp, the Z1 circuitgrounding point is the left side of the radiator closure
panel.
²For the right front parking lamp, turn signal,
side marker lamp and right headlamp, the Z1 circuit
grounding point is in the right fender side shield.
²Circuit L7 also feeds the radio, if equipped.
²When the headlamp switch is in the PARK or
ON position, the dimmer circuit, F33, also connects
to circuit E1. Circuit E1 powers the ash receiver
lamp, transmission range indicator lamp, instrument
panel cluster illumination lamps, HVAC control
lamp, heated rear window lamp, and radio lamp. A 4
amp fuse, in cavity 12 of the fuse block, protects cir-
cuit E1.
HEADLAMPS
The headlamp switch has 3 positions, ON, PARK
(parking lights) and OFF. Two circuits, L2 and L20
connect the headlamp switch to the headlamp dim-
mer/optical horn switch located in the multi-function
switch. The multi-function switch feeds the low and
high beams of the headlamps.
HEADLAMP SWITCH IN OFF OR PARKING
LAMP POSITION
Circuit A3 originates in the Power Distribution
Center (PDC) and supplies battery voltage for the
headlamp switch. A 40 amp fuse protects the A3 cir-
cuit. The headlamp switch has an internal 24 amp
circuit breaker that connects circuit A3 to either the
L2 or L20 circuits, depending on switch position.
In the OFF and PARK positions the headlamp
switch feeds the L20 circuit that connects to the
multi-function switch. Circuit L20 powers the high
beam circuit when the operator flashes the head-
lamps with the turn signal stalk of the multi-func-
tion switch. When the operator flashes the
headlamps with the stalk, the multi-function switch
connects the L20 circuit to the L3 circuit. The L3 cir-
cuit feeds the high beam of the headlamps.
HEADLAMP SWITCH IN ON POSITION
When the headlamp switch is in the ON position,
it connects the A3 circuit from the PDC to circuit L2.
PL8W - 50 FRONT LIGHTING 8W - 50 - 7

Page 153 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 8W-51 REAR LIGHTING
INDEX
page page
DESCRIPTION AND OPERATION
BACK-UP LAMPS....................... 10
FOG LAMPS (REAR)...................... 9S

Downloaded from www.Manualslib.com manuals search engine 8W-51 REAR LIGHTING
INDEX
page page
DESCRIPTION AND OPERATION
BACK-UP LAMPS....................... 10
FOG LAMPS (REAR)...................... 9STOP LAMPS.......................... 10
TAIL LAMPS AND LICENSE LAMPS.......... 9
DESCRIPTION AND OPERATION
TAIL LAMPS AND LICENSE LAMPS
Circuit A3 in the Power Distribution Center (PDC)
connects to a bus bar in the fuse block. One of the
four circuits powered by the bus bar is circuit F33. A
40 amp fuse in the PDC protects the A3 circuit. A 15
amp fuse, in cavity number 2 of the fuse block, pro-
tects the F33 circuit.
The headlamp switch has 3 positions, ON, PARK
(tail lamps) and OFF, plus a dimmer switch. When
the headlamp switch is in the PARK or ON position,
it connects circuit F33 to circuit L7. From the head-
lamp switch, circuit L7 branches to power the front
parking lamps, rear tail lamps, side marker lamps,
and rear license plate lamp.
GROUND CIRCUIT
Circuit Z1 provides ground for the tail lamps, park-
ing lamps, headlamps, side marker lamps, lamps and
rear license plate lamps although different grounding
points are used. Circuit Z1 also provides the ground
path for the headlamps, stop lamps and turn signals.
HELPFUL INFORMATION
²Check for a blown 40 amp fuse in the PDC.
²Check for a blown fuse in cavity 2 of the fuse
block
²For the left rear parking lamp, turn signal, side
marker lamp, and the rear license plate the Z1 cir-
cuit grounding point is in the left rear wheel well.
²For the right rear parking lamp, turn signal and
side marker lamp, the Z1 circuit grounding point is
in the right rear wheel well.
²Circuit L7 also feeds the radio, if equipped.
²When the headlamp switch is in the PARK or
ON position, the dimmer circuit, F33, connects to cir-
cuit E1. Circuit E1 powers the ash receiver lamp,
transmission range indicator lamp, instrument panel
cluster illumination lamps, HVAC control lamp,
heated rear window lamp, and radio lamp. A 4 amp
fuse, in cavity 12 of the fuse block, protects circuit
E1.
FOG LAMPS (REAR)
The rear fog lamps will operate only when the
headlamp switch is in the ON position.
Circuit A3 from the Power Distribution Center sup-
plies (PDC) voltage to a bus bar in the fuse block.
Circuit F61 is one of four circuits that the bus bar
feeds and is protected by a 20 amp fuse in cavity 4.
Circuit F61 connects to the rear fog lamp switch and
the front fog lamp relay.
The fog lamp switch contains a relay that supplies
voltage to the fog lamps. Circuit L2 from the multi-
function switch supplies voltage to the coil side of the
relay (only when the headlamps operate on LOW
beam). Circuit F61 supplies voltage to the contact
side of the relay. During LOW beam headlamp oper-
ation when the fog lamp switch contacts CLOSE, cir-
cuit F61 connects to circuit L38.
Circuit L38 feeds right and left fog lamp. Circuit
L38 also feeds the green L.E.D. in the switch that
illuminates during fog lamps operation.
When the headlamp switch is in the PARK or ON
position, circuit E1 from the headlamp switch sup-
plies voltage for circuit E2. Circuit E2 contains a 4
amp fuse in cavity 12 of the fuse block, and powers
the bulb in the fog lamp switch.
GROUND CIRCUIT
Although circuit Z1 provides the ground path for
the fog lamps, the circuit has different grounding
points for each lamp.
Circuit Z3 supplies the ground path for the fog
lamp switch. The grounding point for the headlamp
switch is the instrument panel left center support.
HELPFUL INFORMATION
²Circuit Z1 also supplies ground for side marker
lamps, turn signals, parking lamps and headlamps.
²Circuit A3 from the PDC supplies voltage to the
headlamp switch for circuit L2.
²Circuit F33 from the fuse block supplies voltage
to the headlamp switch for circuit E1. Circuit A3
from the PDC supplies voltage to a bus bar in the
fuse block that feeds the F33 circuit. Fuse 2, in the
fuse block, protects the F33 circuit.
PL8W - 51 REAR LIGHTING 8W - 51 - 9

Page 190 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine Component Page
Left Power Mirror...................8W-80-23
Left Power Window Switch............8W-80-23
Left Rear Door Lock Motor............8

Page 216 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 978W-1
PL-RHD 8W - 80 - 28 8W-80 CONNECTOR PIN-OUTS
PLR08028
*2.0L (SOHC) ENGINEl2.0L (DOHC) ENGINE
CAV CIRCUIT FUNCTION
25 Ð Ð
26 K2 20TN/DB

Page 217 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine 978W-1
8W - 80 - 29 PL-RHD 8W-80 CONNECTOR PIN-OUTS
PLR08029
CAV CIRCUIT FUNCTION
1Ð Ð
2 X55 22BR/RD LEFT FRONT SPEAKER (Ð)
3 X56 22DB/RD RI

Page 227 of 256

DODGE NEON 1997 1.G Wiring Diagrams Workshop Manual Downloaded from www.Manualslib.com manuals search engine Connector
Name/NumberColor Location Fig.
Power Folding
Mirror RelayBK Near Power
MirrorN/S
Power Mirror Fuse
HolderBK Near Power
MirrorN/S
Powe

Downloaded from www.Manualslib.com manuals search engine Connector
Name/NumberColor Location Fig.
Power Folding
Mirror RelayBK Near Power
MirrorN/S
Power Mirror Fuse
HolderBK Near Power
MirrorN/S
Power Mirror Switch
C1BK At Switch 12
Power Mirror Switch
C2BK At Switch 12
Power Steering
Pressure SwitchGY Rear of Steering
Gear5
Power Sunroof
MotorRD At Motor 9
Powertrain Control
Module C1BK Left Fender Side
Shield5
Powertrain Control
Module C2BK Left Fender Side
Shield5
PRNDL Lamp BK Rear of
Gearshift11
Radiator Fan Motor BK Rear of Fan 6
Radio C1 BK Rear of Radio 13
Radio C2 GY Rear of Radio 13
Rear Fog Lamp
SwitchBK At Switch N/S
Rear Window
Defogger SwitchBK Rear of Switch 13
Right Airbag Impact
SensorGY Right Side
Radiator Closure
Panel1
Right Back-Up
LampGY At Lamp 20
Right Door Lock
SwitchWT At Switch 12
Right Door Window
MotorBK At Motor 12
Right Fog Lamp BK Rear of Fascia 4
Right Front Door
Lock MotorBK At Motor 12
Right Front Door
SpeakerBK At Speaker 12
Right Front Wheel
Speed SensorGY Right Fender
Side Shield4
Right Headlamp BK Rear of Lamp 4
Right Headlamp
Leveling MotorBK Rear of Right
Headlamp4
Right Instrument
Panel SpeakerBK At Speaker N/SConnector
Name/NumberColor Location Fig.
Right License Lamp NAT At Lamp 18
Right Park/Turn
Signal LampNAT At Lamp 4
RIght Power Mirror BK At Mirror 12
Right Rear Door
Lock MotorBK Rear of Door 15
Right Rear Fog
LampNAT At Lamp N/S
Right Rear Speaker BK At Speaker 16
Right Rear Wheel
Speed SensorBK Right Rear
Frame RailN/S
Right Repeater
LampBK At Lamp N/S
Right TaIl/Stop
LampBK At Lamp 4
Right Turn Signal
LampBK At Lamp 20
Solid State Fan
RelayBK Left Front Frame
Rail6
Stop Lamp Switch GY Top of Brake
Pedal2
Sunroof Slide
SwitchBL At Switch 9
Sunroof Vent
SwitchYL At Switch 9
Throttle Position
SensorBK On Throttle
Body8
Torque Converter
Clutch SolenoidBK Top of
Transmission3
Trunk Lamp BK At Lamp 17
Turn Signal/Hazard
SwitchBK Rear of Switch 10
Upstream Heated
Oxygen SensorGY Right Rear of
Engine4, 7
Vapor Canister
Leak DetectorBK Right Front
FenderN/S
Vehicle Speed
SensorBK Rear of
Transmission3
Windshield Washer
Pump MotorBK Bottom of
Reservior6
Wiper Motor BK Right Side of
Cowl PanelN/S
PL8W - 90 CONNECTOR/GROUND LOCATIONS 8W - 90 - 3
DESCRIPTION AND OPERATION (Continued)

Page: < prev 1-8 9-16 17-24

heating sport mode seat adjustment park assist clock reset drain bolt