1997 DODGE NEON Radiator fan

Downloaded from www.Manualslib.com manuals search engine ²Circuit K59 connects to cavity 58 of the PCM
connector.
²Circuit K60 connects to cavity 49 of the PCM
connector.
POWER STEERING PRESSURE SWITCH
The power steering pressure switch opens and
closes circuit K10 between the Powertrain Control
Module (PCM) and ground. Circuit K10 connects to
cavity 45 of the PCM connector.
Circuit Z12 provides ground for the power steering
pressure switch. The grounding point for circuit Z12
is the left side of the radiator closure panel.
TORQUE CONVERTER CLUTCH SOLENOID (TCC)
The Powertrain Control Module (PCM) operates
the TCC solenoid by providing a ground path on cir-
cuit K54. Circuit K54 connects to PCM cavity 79.
Circuit F12 supplies battery voltage to the TCC
solenoid. Circuit F12 connects to a bus bar in the
fuse block fed by circuit A21. A 15 amp fuse in the
fuse block, cavity 10, protects circuit F12. Circuit F12
connects to cavity 20 of the PCM connector.
HELPFUL INFORMATION
Circuit F12 splices to feed the ABS control module,
PCM, EGR solenoid, leak detection pump, and the
duty cycle EVAP/Purge solenoid. The F12 circuit also
connects to a bus bar in the PDC that supplies volt-
age to the coil side of radiator fan relay, A/C clutch
relay, and fuel pump relay.
In the RUN or START position, the ignition switch
connects circuit A1 from the fuse block and circuit
A21. Circuit A1 connects to battery voltage and is
protected by a 30 amp fuse in the PDC.
DUTY CYCLE EVAP/PURGE SOLENOID
Circuit F12 supplies battery voltage to the Duty
Cycle EVAP/Purge solenoid. The Powertrain Control
Module (PCM) switches ground path for the solenoid
ON and OFF through circuit K52.
Circuit F12 connects to a bus bar in the fuse block
fed by circuit A21. A 15 amp fuse in the fuse block,
cavity 10, protects circuit F12. Circuit F12 also con-
nects to cavity 20 of the PCM connector.
Circuit K52 connects to cavity 68 of the PCM, and
cavity 1 of the solenoid connector.
HELPFUL INFORMATION
Circuit F12 splices to feed the ABS control module,
PCM, EET solenoid, leak detection pump, and the
TCC solenoid. The F12 circuit also connects to a bus
bar in the PDC that supplies voltage to the coil side
of radiator fan relays, A/C clutch relay, and fuel
pump relay.
In the START or RUN position, the ignition switch
connects circuit A1 from the fuse block and circuitA21. Circuit A1 connects to battery voltage and is
protected by a 30 amp fuse in the PDC.
EGR TRANSDUCER (EET) SOLENOID
Circuit F12 supplies battery voltage to the EET
solenoid. The Powertrain Control Module (PCM)
switches ground path for the solenoid ON and OFF
through circuit K35.
Circuit F12 connects to a bus bar in the fuse block
fed by circuit A21. A 15 amp fuse in the fuse block,
cavity 10, protects circuit F12. Circuit F12 also con-
nects to cavity 20 of the PCM.
Circuit K35 connects to cavity 40 of the PCM con-
nector.
HELPFUL INFORMATION
Circuit F12 splices to feed the ABS control module,
PCM, Duty Cycle EVAP/Purge solenoid, leak detec-
tion pump, and the TCC solenoid. The F12 circuit
also connects to a bus bar in the PDC that supplies
voltage to the coil side of radiator fan relays, A/C
clutch relay, and fuel pump relay.
In the START or RUN position, the ignition switch
connects circuit A1 from the fuse block and circuit
A21. Circuit A1 connects to battery voltage and is
protected by a 30 amp fuse in the PDC.
LOW FUEL DETECT INPUT
Circuit G4 provides an input to the Powertrain Con-
trol Module (PCM) indicating fuel tank level. This cir-
cuit connects to cavity 23 of the PCM connector.
The G4 circuit is also used for the fuel gauge
located in the instrument cluster. For operation of
the fuel gauge, refer to section 8W-40.
PARK/NEUTRAL POSITION SWITCH INPUT (3±SPD
TRANSMISSION)
On vehicles equipped with the 3±spd automatic
transmission the park/neutral switch provides an
input to the Powertrain Control Module (PCM).
When CLOSED, the park/neutral position switch
provides a ground path on circuit T41 for the coil
side of the engine starter motor relay. The case
grounded switch provides ground for circuit T41.
Circuit A41 from the ignition switch provides bat-
tery voltage to the coil side of the relay.
Circuit T41 splices to cavity 76 of the PCM. The
park/neutral position switch provides an input to the
Powertrain Control Module (PCM).
HELPFUL INFORMATION
In the START position, the ignition switch connects
circuit A1 from the Power Distribution Center (PDC)
to circuit A41. A 30 amp fuse protects circuits A1 and
A41.
PL8W - 30 FUEL/IGNITION SYSTEMS 8W - 30 - 19
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine 8W-42 AIR CONDITIONING-HEATER
INDEX
page
SCHEMATICS AND DIAGRAMS........................................................... 1
DESCRIPTION AND OPERATION.......................................................... 6
Component Page
A/C Compressor Clutch................8W-42-2
A/C Compressor Clutch Relay...........8W-42-2
A/C Cycling Switch...............8W-42-3, 4, 5
A/C Heater Blower Motor..............8W-42-3
A/C Heater Control Switch...........8W-42-3, 3
A/C High Pressure Switch..............8W-42-5
A/C Low Pressure Switch............8W-42-4, 5
Blower Motor Resistor Block............8W-42-3
Diode..............................8W-42-2
Fuse 5 (FB).........................8W-42-4
Fuse 5 (PDC)........................8W-42-5
Fuse 7 (FB).........................8W-42-3
Fuse 9 (FB).........................8W-42-3
Fuse 10 (FB)........................8W-42-2
Fuse 18 (PDC).......................8W-42-2
Fuse Block......................8W-42-2, 3, 4Component Page
G101..............................8W-42-5
G103..............................8W-42-2
G203..............................8W-42-3
Headlamp Switch....................8W-42-3
Power Distribution Center...........8W-42-2, 5
Powertrain Control Module...........8W-42-2, 5
Radiator Fan Motor..................8W-42-5
Rear Fog Lamp Switch................8W-42-3
S108..............................8W-42-5
S109..............................8W-42-2
S111 ..............................8W-42-5
S204..............................8W-42-3
S210..............................8W-42-3
S211 ..............................8W-42-4
S314..............................8W-42-3
Solid State Fan Relay.................8W-42-5
8W - 42 - 2 8W - 42 AIR CONDITIONING-HEATERPL

Downloaded from www.Manualslib.com manuals search engine 30A
FUSE
5
5 73
BATT A0
POWER
DISTRIBUTION
CENTER
1
2A16
14
GY
RELAY FAN
STATE
SOLID
C2
18
K173
20
DG
K173
20
LG
13C160
Z1
18
BK
S111
Z1
14
BK
Z1
14
BK
C25
14
LG
Z1
14
BK
G101
S108
POWERTRAIN
CONTROL
MODULE MOTOR FAN
RADIATOR
4
13
BR18 C20
DB/OR22 C21
A/C
HIGH
PRESSURE
SWITCH A/C
LOW
PRESSURE
SWITCH
C2
38
DB/OR20 C21
C2063
2
1
2
1
C1605
SENSE SWITCHA/C
BR/OR20 C20
DB/WT20 C22
DB/OR22 C21
1
2
A/C
CYCLING
SWITCH
RADIATOR
FAN
RELAY
CONTROLA/C
CYCLING
SWITCH
OUTPUT
2C101
(8W-10-7)(8W-10-4)
(8W-15-2)
(8W-15-2) (8W-15-2)
(8W-30-11) (8W-10-4)
(8W-42-4)
M
PL-RHD8W-42 AIR CONDITIONING-HEATER 8W - 42 - 5
PLR04204978W-1

Downloaded from www.Manualslib.com manuals search engine 8W-42 AIR CONDITIONING-HEATER
INDEX
page page
DESCRIPTION AND OPERATION
A/C OPERATION......................... 6
AIR CONDITIONING-HEATER SYSTEM....... 6BLOWER MOTOR OPERATION............. 6
HELPFUL INFORMATION.................. 7
RADIATOR FAN OPERATION............... 6
DESCRIPTION AND OPERATION
AIR CONDITIONING-HEATER SYSTEM
The A/C-Heater System is powered by a by several
fuses. Fuse 10, a 15 amp fuse located in the fuse
block, is HOT in the RUN position. This fuse powers
the coil side of the A/C compressor clutch relay
located in the Power Distribution Center (PDC).
A 30 amp fuse, on circuit A16 located in the PDC,
powers the solid state radiator fan relay. This fuse is
HOT at all times. The 10 amp fuse on circuit A17
located in the PDC powers the contact side of the A/C
compressor clutch relay.
The A/C-Heater blower motor is protected by a 25
amp fuse located in cavity 7 of the fuse block. This
fuse in HOT in the RUN position only. When the
ignition switch is in the RUN position, power is sup-
plied to the fuse on circuit A22. The power leaves the
fuse on circuit C1 and goes directly to the blower
motor.
There is a 4 amp fuse located in cavity 12 of the
fuse block used for the illumination lamps in the A/C-
Heater control. The fuse is HOT at all times.
A/C OPERATION
When the A/C or the defrost switch is put in the
ON position, and the A/C cycling switch, low pressure
cut-out switch, and the high pressure switch are
CLOSED, the Powertrain Control Module (PCM)
receives a request for A/C.
After receiving this input, the PCM activates the
A/C compressor by grounding the C28 circuit on the
coil side of the A/C Compressor Clutch relay. Power
for the coil side of the relay is supplied on the bus
bar located in the Power Distribution Center (PDC).
With the coil energized, current flows from the 10
amp fuse in the PDC on circuit A17 through the
CLOSED contacts in the relay, on the C3 circuit to
the A/C compressor clutch.
The A/C compressor clutch receives this voltage
and creates a magnetic field energizing the clutch.
Ground for the coil is provided at the right headlamp
ground.
The connector at the A/C compressor has a diode
located in it. This diode is used to control the inducedvoltage resulting from the magnetic field collapsing
when the clutch is disengaged. The diode provides a
path for the voltage to protect other components and
systems.
The A/C compressor clutch relay is also used by the
PCM to disengage the compressor in a Wide Open
Throttle (W.O.T.) condition.
RADIATOR FAN OPERATION
The radiator fan system used in this vehicle uses a
solid state relay that controls the speed of the radia-
tor fan.
Power for the relay is supplied on circuit A16 This
circuit is HOT at all times and protected by a 30 amp
fuse located in the Power Distribution Center (PDC).
Ground for the coil side of the relay is controlled by
the Powertrain Control Module (PCM). When the
PCM determines the need for fan operation the PCM
supplies the ground path for circuit K173. This cir-
cuit connects to cavity 18 of the PCM connector.
From the relay circuit C25 connects to the radiator
fan motor(s). On vehicles equipped with the manual
transmission only one radiator fan is used. For vehi-
cles equipped with an automatic transmission there
are two radiator fans used.
Ground for the radiator fans is supplied on circuit
Z1.
BLOWER MOTOR OPERATION
With the ignition switch in the RUN position,
power flows from the 25 amp fuse, in cavity 7 of the
fuse block, to the blower motor. Blower motor speed
is controlled by the fan control switch located in the
instrument panel, and the resistor block.
Blower motor LOW speed operation is accom-
plished on the C4 circuit. When the control switch is
moved to the LOW speed position, current is passed
on the C7 circuit through the blower motor resistor
to the C4 circuit. It then flows through the blower
motor switch to the Z8 circuit. The Z8 circuit termi-
nates at a grounding point on the instrument panel
left center support.
The operation of the blower motor M1 and M2
speed operations is the same as the LOW speed
8W - 42 - 6 8W - 42 AIR CONDITIONING-HEATERPL

Downloaded from www.Manualslib.com manuals search engine except, the C5 circuit is used for the M1 speed and
circuit C6 is used for M2 speed operation.
Blower motor HIGH speed operation is accom-
plished on the C7 circuit which supplies battery volt-
age directly to the blower motor. There are no
resistors used in the HIGH speed mode.
HELPFUL INFORMATION
²Check the 30 amp fuse located in the PDC for
the radiator fan motor
²Check the 15 amp fuse located in cavity 10 of
the fuse block for the A/C compressor clutch relay
²Check the 10 amp fuse located in the PDC for
the A/C compressor clutch relay.
²Check the 25 amp fuse located in cavity 7 of the
fuse block for the blower motor.
²Check the right headlamp ground located at the
right fender side shield.
²Check the left headlamp ground located on the
left side of the radiator closure panel.
²On vehicles equipped with A/C check the refrig-
erant level. The system will not operate with a low
level of refrigerant.
PL8W - 42 AIR CONDITIONING-HEATER 8W - 42 - 7
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine Component Page
Left Power Mirror...................8W-80-23
Left Power Window Switch............8W-80-23
Left Rear Door Lock Motor............8W-80-23
Left Rear Fog Lamp.................8W-80-23
Left Rear Speaker...................8W-80-23
Left Rear Wheel Speed Sensor.........8W-80-23
Left Repeater Lamp.................8W-80-24
Left Tail/Stop Lamp.................8W-80-24
Left Turn Signal Lamp...............8W-80-24
Map/Reading Lamps.................8W-80-24
Master Power Window Switch..........8W-80-24Component Page
Park/Neutral Position Switch (ATX).....8W-80-25
Passenger Side Airbag................8W-80-25
Power Folding Mirror Relay...........8W-80-25
Power Mirror Fuse Holder............8W-80-25
Power Mirror Switch - C1.............8W-80-25
Power Mirror Switch - C2.............8W-80-26
Power Steering Pressure Switch........8W-80-26
Power Sunroof Motor.................8W-80-26
Powertrain Control Module - C1........8W-80-26
Powertrain Control Module - C2........8W-80-27
PRNDL Lamp......................8W-80-28
Radiator Fan Motor..................8W-80-28
Radio - C1.........................8W-80-28
Radio - C2.........................8W-80-29
Rear Fog Lamp Switch...............8W-80-29
Rear Window Defogger Switch.........8W-80-29
Right Airbag Impact Sensor...........8W-80-29
Right Back-Up Lamp.................8W-80-29
Right Door Lock Switch...............8W-80-30
Right Door Window Motor.............8W-80-30
Right Fog Lamp....................8W-80-30
Right Front Door Lock Motor..........8W-80-30
Right Front Door Speaker.............8W-80-30
Right Front Wheel Speed Sensor........8W-80-31
Right Headlamp....................8W-80-31
Right Headlamp Leveling Motor........8W-80-31
PL8W - 80 CONNECTOR PIN-OUTS 8W - 80 - 3
DESCRIPTION AND OPERATION (Continued)

Downloaded from www.Manualslib.com manuals search engine 978W-1
PL-RHD 8W - 80 - 28 8W-80 CONNECTOR PIN-OUTS
PLR08028
*2.0L (SOHC) ENGINEl2.0L (DOHC) ENGINE
CAV CIRCUIT FUNCTION
25 Ð Ð
26 K2 20TN/DB*ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
26 K2 20TN/BKlENGINE COOLANT TEMPERATURE SENSOR SIGNAL
27 Ð Ð
28 Ð Ð
29 Ð Ð
30 K41 20BK/DG UPSTREAM HEATED OXYGEN SENSOR SIGNAL
31 Ð Ð
32 K24 20GY/BK CRANKSHAFT POSITION SENSOR SIGNAL
33 K44 20TN/YL CAMSHAFT POSITION SENSOR SIGNAL
34 Ð Ð
35 K22 20OR/DB THROTTLE POSITION SENSOR SIGNAL
36 K1 18DG/RD MANIFOLD ABSOLUTE PRESSURE SENSOR SIGNAL
37 K21 18BK/RD INTAKE AIR TEMPERATURE SENSOR SIGNAL
38 C20 18BR A/C SWITCH SENSE
39 Ð Ð
40 K35 20GY/YL EXHAUST GAS RECIRCULATION SOLENOID CONTROL
(CONTINUED)
CAV CIRCUIT FUNCTION
1 E2 22OR FUSED PANEL LAMPS DIMMER SWITCH SIGNAL
2 Z3 20BK/OR GROUND
BLACK
1 2
PRNDL
LAMP
CAV CIRCUIT FUNCTION
1 C25 14LG RADIATOR FAN RELAY OUTPUT
2 Z1 14BK GROUND
RADIATOR
FAN MOTOR
CAV CIRCUIT FUNCTION
1Ð Ð
2 X51 22BR/YL LEFT REAR SPEAKER (Ð)
3 X52 22DB/WT RIGHT REAR SPEAKER (+)
4 X53 22DG LEFT FRONT SPEAKER (+)
5 X54 22VT RIGHT FRONT SPEAKER (+)
6 X57 22BR/LB LEFT REAR SPEAKER (Ð)
7 X58 22DB/OR RIGHT REAR SPEAKER (Ð)
1
BLACK
2
RADIO - C1
BLACK
7
1

Downloaded from www.Manualslib.com manuals search engine 978W-1
8W - 80 - 33 PL-RHD 8W-80 CONNECTOR PIN-OUTS
PLR08033
STOP LAMP
SWITCH 61
CAV CIRCUIT FUNCTION
1 K29 20WT/PK STOP LAMP SWITCH SENSE
2 Z12 20BK/TN GROUND
3Ð Ð
4Ð Ð
5 L50 20WT/TN STOP LAMP SWITCH OUTPUT
6 F32 18PK/DB FUSED B(+)
GRAY
CAV CIRCUIT FUNCTION
1 Z1 18BK GROUND
2 K173 20DG RADIATOR FAN RELAY CONTROL
3 C25 14LG ENGINE FAN FEED
4 A16 14GY RADIATOR FAN RELAY FEED
SOLID STATE FAN RELAY
CAV CIRCUIT FUNCTION
1 L60 18TN RIGHT TURN SIGNAL
2 Z1 18BK GROUND
RIGHT REPEATER
LAMP
CAV CIRCUIT FUNCTION
1 L50 18WT/TN TAIL/STOP
2 L7 18BK/YL TAIL/STOP
3 Z1 18BK GROUND
RIGHT TAIL/STOP LAMP
CAV CIRCUIT FUNCTION
1 L63 18DG/RD RIGHT TURN SIGNAL LAMP FEED
2 Z1 18BK GROUND
RIGHT TURN SIGNAL LAMP
2 1
NATURAL
3 1 2
BLACK
2 1
GRAY
BLACK
1 4