1997 CHEVROLET TRACKER instrument panel

ACC (B): The position in which you can operate your
electrical power accessories. It unlocks the steering
wheel and ignition. Use this position if your vehicle
must
be pushed or towed.
ON (C): The position that the switch returns to after you
start your engine and release the switch. The switch
stays in the
ON position when the engine is running. But
even when the engine is not running, you can use
ON to
operate your electrical power accessories and to display
some instrument panel warning and indicator lights.
START (D): The position that starts the engine. When
the engine starts, release the key. The ignition switch
will return to
ON for normal driving.
When the engine is not running,
ACC and ON allow you
to operate your electrical accessories, such as the radio
and ventilation fan.
A warning chime will sound if you open the driver’s
door when the ignition is in
ACC or LOCK and the key
is in the ignition.
I A CAUTION:
On manual transmission vehicles, turning the key
to
LOCK will lock the steering column and result
in
a loss of ability to steer the vehicle. This could
cause
a collision. If you need to turn the engine
off while the vehicle is moving, turn the key only
to
ACC. Don’t push the key in while the vehicle
is moving.
I
NOTICE:
If your key seems stuck in LOCK and you can’t
turn it, be sure you are using the correct key; if
so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using
a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.
2-8
ProCarManuals.com

Power Mode Selector Switch (If Equipped)
A power mode selector switch is included with the
four-speed automatic transmission. When
you need
more power for climbing hills or quicker acceleration,
press the P (POWER) switch. The POWER indicator
light on the instrument panel comes on. For normal
driving, press the
N (NORMAL) switch. The POWER
indicator light goes
off.
Overdrive Off Switch (If Equipped)
The overdrive off switch is located on the left side of the
shifter.
By operating the overdrive off switch, the
four-speed automatic transmission (three-speed plus overdrive) can be converted to a three-speed automatic
transmission. While in the three-speed mode, the
transmission will not shift into the overdrive position.
To convert the transmission to the three-speed mode,
push in the overdrive
off switch and release it. The
switch comes out and the
OD OFF indicator light on
the instrument panel comes on.
To return the transmission to the four-speed mode, push
in the overdrive
off switch again. The switch will remain
in and the
OD OFF indicator light goes off.
Please note that if the transfer lever is in the
4L position,
the four-speed automatic transmission will remain in the
three-speed mode.
Manual Transmission
5-Speed
This is your shift pattern. Here's how to operate
your transmission:
FIRST (1): Press the clutch pedal and shift into
mRST
(1). Then, slowly let up on the clutch pedal as
you press the accelerator pedal.
2-14
ProCarManuals.com

Yhrn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a
turn or a lane change.
To signal a turn, move the lever all the way
up or down.
When the
turn is finished, the lever will return automatically.
Q
An arrow on the instrument
panel will flash in the
direction of the turn or
lane change. To
signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until
you
complete your lane change. The lever will return by
itself when
you release it.
As
you signal a turn or a lane change, if the arrows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb
is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the fuse (see
“Fuses and Circuit
Breakers”
in the Index) and for burned-out bulbs.
2-30
ProCarManuals.com

Lamps Control
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.
OFF: All lamps are off.
lamp and the instrument panel lights come on. The
headlamps are
off.
-:(% : The headlamps and all other operating lamps
come
on.
Lamps On Reminder
If you turn the ignition off, remove the key, open the
door and leave the lamps on,
a chime will remind you to
turn off your lamps.
Headlamp High/Low Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever away from you.
When the high beams are
on, a light on the instrument
panel also will be
on. It will
go off when you switch to
low beam.
To switch back to low beams, pull the lever toward you.
ProCarManuals.com

Setting Cruise Control
If you leave your cruise control switch on when
you’re not using cruise, you might hit a button
and
go into cruise when you don’t want to. You
could be startled and even lose control. Keep the
cruise control switch
off until you want to use it.
1. Press the CRUISE CTRL switch on
the instrument
panel to
turn the
system on. The
indicator light on
the switch will
come on.
2. Get up to the speed you want.
3. Once you’re going 25 mph (40 km/h) or more, turn
the lever to COASTBET and release. Your cruise
will set.
4. Take your foot off the accelerator pedal.
2-35
ProCarManuals.com

When you turn on the headlamp switch, your DRL will
go out, and your headlamps will come on.
The other lamps that come
on with your headlamps will
also come on.
When you turn off the headlamp switch, the regular
lamps will go off, and your low-beam headlamps will
come on at the reduced brightness of
DRL.
To idle your vehicle with the DRL off, set the parking
brake. The
DRL will stay off until you release the
parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Interior Lamps
Instrument Panel Brightness Control
This knob controls the
brightness of your
instrument panel lights.
Turn the knob to the right to
brighten the lights or to the
left to dim them.
2-38
ProCarManuals.com

Outside Manual Adjust Mirrors Power Remote Control Mirrery
(If Equipped)
The switch to control the
power mirrors is located on
the instrument panel.
You
can only adjust the mirrors
when the ignition switch is
in the
ON position.
Adjust
these mirrors by hand so that you can just see the
side
of your vehicle when you are sitting in a
comfortable driving position.
10 adjust the mirrors:
1. Move the selector switch to the left or right to select
the mirror you wish to adjust.
direction
you want to move the mirror.
2. Press the outer part of the switch that matches the
3. Return the selector switch to the center position to
help prevent moving the mirror accidentally.
2-40
ProCarManuals.com

Instrument Panel
/

-

2-58
ProCarManuals.com