1997 CADILLAC DEVILLE CD player

Downloaded from www.Manualslib.com manuals search engine 0 AUDITORIUM: This setting is similar to LIVE,
however, more echo is present. The LIVE and
AUDITORIUM settings are best used for music.
LEVEL: Press the plus or minus symbol on this button
to adjust the amount
of effect desired when in DSP
mode. Some experimenting with this button will help you determine the best sound.
Adjusting the Speakers
BAL: Press this knob lightly so it extends. Turn the
knob clockwise to adjust sound to the right speakers and
counterclockwise for the left speakers. The middle
position balances the sound between the speakers.
FADE: Press this knob lightly so it extends. Turn the
knob clockwise to adjust the sound to the front speakers
and counterclockwise for the rear speakers. The middle
position balances the sound between the speakers.
Push these
knobs back into their stored positions when
you’re not using them.
Playing a Cassette Tape
With the radio on, insert a cassette tape. The tape will
begin playing as soon as it is inserted.
While the tape is playing, use the VOL, FADE, BAL,
BASS and TREB controls just as you do for the radio.
Other controls may have different functions when a tape
is inserted. The display will show TAPE with an arrow
to indicate which side
of the tape is playing. PLAY will
appear on the display temporarily when a tape
is
playing. The display will then revert back to showing
the time.
If an error occurs while trying to play a cassette tape, it
could be that:
0
0
The cassette tape is tight and the cassette player
cannot turn the hubs of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with a pencil. Flip the tape
over and repeat. If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used in the player. Try a new tape to be sure your
player is working properly.
The cassette tape is broken. (Check to see if your
tape
is broken. Try a new tape.)
3-24

Downloaded from www.Manualslib.com manuals search engine REV: Press the left arrow to reverse the tape rapidly.
Press
it again to return to playing speed. The radio will
play while the tape reverses and
REV will appear on the
display. You may use your station pushbuttons to tune to
another radio station while in
REV mode.
FF: Press the right arrow to fast forward to another part
of the tape. Press it again to return to playing speed. The
radio will play while the tape advances and
FF will
appear on the display. You may use your station
pushbuttons to tune to another radio station while in
FF mode.
SEEK-TUNE: Press the right arrow to seek to the next
selection on the tape. Press the left arrow to search for
the previous selection on the tape (REP will appear on
the display). Your tape must have at least three seconds
of silence between each selection for SEEK-TUNE to
work. The sound will mute while seeking.
SCAN: Press this button. SCAN FF will appear on the
display until the next selection is found and then SCAN
PLAY will appear on the display. Use SCAN to listen to
selections for a few seconds. The tape will go to a
selection, stop for a few seconds, then go on to the next
selection. Press this button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing. (PLAY shows on the display.)
SOURCE: Press this button to switch from radio to
cassette tape play. If no cassette tape is in the tape
player, CASS appears on the display and then the radio
station appears briefly. The display then reverts back to
showing the time of day. Press this button again or
BAND to switch back to the radio.
EJECT Press the upward triangle button to remove
a tape. The radio will play. Eject may be activated with the
radio
off if the ignition is on. Cassette tapes may be loaded
with the radio
off but they will not start playing until the
PWR button is pressed. Press
PWR or turn the ignition
key
off to stop the cassette tape player. The tape will stay
in the player and resume play at the point where it
stopped.
If you leave a cassette tape in the player while
listening to the radio, it may become warm.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See “Care
of
Your Cassette Tape Player” in the Index. After you clean
the player, press and hold EJECT for five seconds to
reset the
CLN indicator. The radio will display --- to
show the indicator was reset.
Dolby@ Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks
of
Dolby Laboratories Licensing Corporation.
3-25

Downloaded from www.Manualslib.com manuals search engine Once you have loaded the discs in the magazine, slide
open the door
of the compact disc (CD) changer. Push
the magazine into the changer in the direction of the
arrow marked
on top of the magazine. Close the door by sliding
it all the way to the left.
If the
door
is left partially open, the changer will not operate
and an error will occur. When the door is closed, the
changer will begin checking for discs in the magazine.
This will continue for up to one and a half minutes,
depending on the number
of discs loaded.
To eject the magazine from the player, slide the CD
changer door all the way open. The magazine will
automatically eject. Remember
to keep the door closed
whenever possible to keep dirt and dust from getting
inside the changer.
3-27

Downloaded from www.Manualslib.com manuals search engine * -1io Steering Wheel Controls Understanding Radio
VO1 ME: Press the up
arrow lever to increase
volume and the down arrow
lever to decrease volume.
SELECT: When listening to the radio, press the up or
down arrow lever to tune to the next or previous radio
station (factory presets which have not been
reprogrammed with your stations will be ignored).
When listening to a cassette tape, the up or down mow
lever can be used to
SEEK forward and rearward
through the tape. Pressing the up or down arrow lever
when listening
to a CD will cause the player to go to the
next or previous selection.
FM Stereo
FM stereo will give you the best sound. But FM signals
will reach only about
10 to 40 miles (1 6 to 65 km). Tall
buildings or hills can interfere with
FM signals, causing
the sound to come and go.
AM
The range for most AM stations is greater than for FM,
especially at night. The longer range, however, can
cause stations to interfere with each other. AM can pick
up noise from things like storms and power lines. Try
reducing the treble to reduce this noise if you ever get it.
Tips About Your Audio System
Hearing damage from loud noise is almost undetectable
until it is too late. Your hearing can adapt to higher
volumes of sound. Sound that seems normal can be loud and harmful to your hearing. Take precautions
by
adjusting the volume control on your radio to a safe
sound level before your hearing adapts to it.
3-30

Downloaded from www.Manualslib.com manuals search engine To help avoid hearing loss or damage:
Adjust the volume control to the lowest setting.
Increase volume slowly until you hear comfortably
and clearly.
NOTICE:
Before you add any sound equipment to your
vehicle
-- like a tape player, CB radio, mobile
telephone or
two-way radio -- be sure you can add
what you want.
If you can, it’s very important to
do it properly. Added sound equipment may
interfere with the operation
of your vehicle’s
engine, Cadillac
radio or other systems, and even
damage them. Your vehicle’s
systems may interfere
with the operation
of sound equipment that has
been added improperly.
So, before adding sound equipment, check with
your dealer and be sure to check Federal rules
covering mobile radio and telephone units.
Care of Your Cassette Tape Player
A tape player that is not cleaned regularly can cause
reduced sound quality, ruined cassettes or a damaged mechanism. Cassette tapes should be stored in their
cases away from contaminants, direct sunlight and
extreme heat. If they aren’t, they may not operate
properly or may cause failure of the tape player.
Your tape player should be cleaned regularly after every
50 hours of use. Your radio may display CLN or CLEAN
TAPE to indicate that you have used your tape player for
50 hours without resetting the tape clean timer. Each time
the cassette is cleaned, the
50 hour cassette timer should
be reset.
This is done by holding down the eject button
for three seconds until the
TAPE CLEAN message is
displayed. If you notice a reduction in sound quality,
try a
known good cassette to see if
it is the tape or the tape
player at fault.
If this other cassette has no improvement
in sound quality, clean the tape player.
Cleaning may be done with a scrubbing action,
non-abrasive cleaning cassette with pads which scrub the
tape head as the hubs of the cleaner cassette turn. It is normal for the cassette to eject while cleaning.
Insert the
cassette at least six times to ensure thorough cleaning.

Downloaded from www.Manualslib.com manuals search engine Some cleaning cassettes or CD adapter kits may appear
as a broken tape. If the cleaning cassette is ejected
immediately from the tape player, follow these steps for
the TAPE CLEAN OVERRIDE feature:
1. Turn the ignition to RUN or ACC.
2. Turn the radio off.
3. Press and hold the SOURCE button for three
seconds. After three seconds, the tape icon will flash
indicating the cut tape feature is now turned
off.
4.
Turn the radio on and insert the cleaning cassette (or
the CD adapter
kit).
5. Eject the tape after the tape player has been cleaned.
When the cleaning cassette has been ejected, the broken
tape detection feature is active again.
You may also choose a non-scrubbing action, wet-type
cleaner which uses a cassette with a fabric belt to clean
the tape head.
This type of cleaning cassette will not
eject and, it may not clean as thoroughly as the
scrubbing type cleaner.
Cassettes
are subject to wear and the sound quality
may degrade over time. Always make sure the cassette
tape is
in good condition before you have your tape
player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc
is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution and
clean it, wiping from the center to the edge.
Be sure never to touch the signal surface when handling
discs. Pick up discs by grasping the outer edges or the
edge of the hole and the outer edge.
Power Antenna Mast Care
Your power antenna will look its best and work well
if it’s cleaned from time to time. To clean the
antenna mast:
1. Turn on the ignition and radio to raise the antenna.
2. Dampen a clean cloth with mineral spirits or
equivalent solvent.
3. Wipe the cloth over the mast sections, removing any dirt.

Downloaded from www.Manualslib.com manuals search engine Rear Compartment Fuse Block
The fuse block is located on the front wall of the trunk
(behind the rear seat) on the driver’s side. Loosen the
four trunk trim fasteners and pull the trim away from the
fuse block to gain access.
, RLY IGN 1 I I SIR I , ELC I I TURN I lGONSOLE1 I BRAKE I I ,
, RSS I IGN , 0-BODY I I COMFORT I I AMP I I PZM I RT/PHOT lCLUSTER,
HTD MIR HTD SEAT R HTD SEAT L PULL DOWN HDLP WASH
, ANTENNA I I RSS I lCONVENCl I BAT I I RSS , I RT PARK I I LT PARK ,
Fuse
RLY IGN1*
SIR
ELC
Usage
Cluster, Cruise in Stalk, PZM, Catalytic Converter Overtemp
Amplifier (Export), TCC Switch
SDM, Left and Ri
.t Door
Sensor
ELC Relay, Vacuum Pump,
ALC Sensor
Electronic Flasher,
Turn/Hazard Switch
- ~~
Fuse
CONSOLE
- -
BRAKE
RSS
IGN 0-BODY
COMFORT
Usage
Rear Zone Blower, Right and
Left Heated Seat Switches
(Optional)
Brake, Vacuum
Pump (VP)
Relay,
VP Motor,
VP Pressure Switch
CV-RTD (CV-RSS)(DeVille Concours Only)
PRNDL, Dual Zone Switch,
PZM, Cluster, Air Control
Module (ACM), Upper Zone
Motor, Lower Zone Motor (Optional), HVAC Solenoids,
Climate Control Panel Analog
Cluster (Console Shift Only),
Rear Defog Relay, ELC Relay
CD Player, Remote Keyless
Entry (RKE), Controlled Power Relay, Air Control Module
(ACM), PZM
6-66

Downloaded from www.Manualslib.com manuals search engine Battery ...................................... 6-30
Jump Starting
................................. 5-4
No Charge Message
........................... 2-89
Replacement. Remote Keyless Entry
.............. 2- 11
Volts High Message ........................... 2-89
Volts Low Message
........................... 2-89
Warnings
................................ 5.4. 5.6
Battery Guard Storage ........................... 2-52
Battery Saver
.................................. 2-50
Exterior Lighting
............................. 2-50
Inadvertent Power
............................ 2-52
BBB Auto Line ................................ 7-11
Better Business Bureau Mediation
.................. 7- 11
Brake Adjustment
.................................. 6-29
Fluid
....................................... 6-27
Master Cylinder
.............................. 6-27
Parking
..................................... 2-28
PedalTravel
................................. 6-29
Replacing System Parts
........................ 6-30
System Warning Light
......................... 2-76
Trailer
...................................... 4-36
Transaxle Shift Interlock
....................... 2-33
Wear
....................................... 6-29
Brake Vacuum Problem Message
.................. 2-90
Brakes. Anti-Lock
............................... 4-7
Braking
........................................ 4-6
Braking
in Emergencies .......................... 4- 10
Break-Iny New Vehicle
.......................... 2-20
Brightness Control .............................. 2-50
Bulb Replacement .............................. 6-3 1
BTSI ......................................... 2-33 Capacities
and Specifications
.................... 6-69
Carbon Monoxide
.................... 2.34.4.29. 4.36
Cassette Tape Player
.................. 3.17.3.20. 3.24
Cassette Tape Player Care
........................ 3-31
CeUularTelephone
.............................. 2-63
Center Console Storage Area
...................... 2-60
Center High-Mounted Stoplamp. Bulb Replacement
... 6-37
Central Door Unlocking System
.................... 2-4
Certification Label
.............................. 4-31
Chains. Tire
................................... 6-48
Change Engine Oil Message
...................... 2-90
Change Trans Fluid Message
...................... 2-90
Changing a Flat Tire
............................. 5-25
Charging System Indicator Light
................... 2-75
Check Brake Fluid
Level Message ................. 2-90
Check Coolant Level Message
..................... 2-90
Check Fuel Gage Message
........................ 2-90
Check Oil Level Message
........................ 2-90
Check Washer Fluid Message
..................... 2-91
Checking Your Restraint Systems
.................. 1-48
Chemical Paint Spotting
.......................... 6-56
Child Restraints
................................ 1-37
Securing in a Rear Outside Seat Position
........... 1-39
Securing in the Center Rear Seat Position
.......... 1-41
Securing in
the Right Front Seat Position .......... 1-43
TopStrap
................................... 1-38
Where to Put
................................ 1-37
Chrome Wheels. Cleaning
........................ 6-54
Cassette Tape Player Errors
............. 3.17. 3.20.
3-24
Center Passenger Position
........................ 1-30
Chains. Safety
................................. 4-36
CHMSL
...................................... 6-37