1997 CADILLAC CATERA clock reset

Downloaded from www.Manualslib.com manuals search engine When you stop your vehicle and turn the ignition key to
LOCK, you can still use the power windows. The
electrical power to operate the windows will not shut off
until a door is opened
-- there is no time limit to this
feature.
As soon as a door is opened, power window
movement will stop immediately.
Programming the Power Windows
If the battery on your vehicle has been disconnected or
is not working, you will need to reprogram each power
window in order for the express-open and close features
to work.
To program each window, press and hold the power
window control until the window has fully opened.
Continue holding the control down for approximately
five more seconds after the window is completely down.
The window is now programmed. Repeat this process
for each window.
Anti-Pinch Feature
If a hand, a head or another object is in the way of the
power window express-closing, the window will
immediately stop at the obstruction and express-open to
a preset factory position.
Note that pressing and holding the power window
control button will override the anti-pinch feature.
Rear Window Lockout
Pressing this button
rearward will disable the
rear passenger window
controls. This is a useful
feature if you have children
as passengers.
Press the
button forward to allow
your passengers to reuse
their window controls.
Horn
The horn can be sounded by pressing either horn symbol
on the steering wheel. The symbols are located at about
the
9 and 3 o’clock positions.

Downloaded from www.Manualslib.com manuals search engine C
L
G
A. Fully Open
B. About 80% Open
C. About 50% Open
D. About 25% Open
E. Fully Closed
E About 40% Tilted
G. Fully Tilted Rotating the control dial
to position
A fully opens the
glass panel and sunshade. The sunshade can also be
opened by hand. If
you want to stop the roof in a
partially opened position, rotate the control dial to any
position between
A and E. The positions range from
about 25% open to approximately 80% open. Rotate the
dial to position
E to fully close the glass panel. To close
the sunshade, pull it forward.
To raise the glass panel, rotate the control dial
counterclockwise to one
of the three tilt positions.
The positions range from about
40% tilted (F) to fully
tilted
(G). To close the vent, rotate the dial clockwise to
position
E.
Anti-Pinch Feature
If a hand, a head or another object is in the way of
the power sunroof closing, the glass panel will
immediately stop at the obstruction and open to
a
preset factory position.
Note that pressing and holding the power sunroof
control dial up will override the anti-pinch feature.
2-52

Downloaded from www.Manualslib.com manuals search engine AM-FM Stereo with Cassette Tape Player
and Optional Compact Disc Player DSPL: Press this button to display the station
being played.
I I Finding a Station
BAND:
Press this button to select AM, FM1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek
to the next higher or lower radio station. Pressing and
holding this button until a chime sounds puts the radio
in a tune mode. In
this mode, higher or lower radio
stations are advanced
to in small increments until the
SEEK-TUNE button is released. Tuning stops when
you release
this button. If you press and hold the
SEEK-TUNE button again within five seconds of being
in the tune mode, tuning will continue. Waiting longer
than five seconds places the radio back in the seek mode.
SCAN: Press this button and SCAN will appear on the
For information on the compact disc player, see "Trunk
display. Use SCAN to listen to stations for a few
Mounted
CD Changer'' later in this section.
seconds. The radio will go to a station, stop for a few
Playing the Radio
PWRNOL:
Press this knob lightly to release it from its
stored position. The system will
turn on. Press the knob
again to
turn the system off. To increase volume, turn the
knob clockwise.
Turn it counterclockwise to decrease
volume. The volume level will appear
on the display. seconds,
then
go on to the next station. Press this button
again
to stop scanning.
3-10

Downloaded from www.Manualslib.com manuals search engine PUSHBUTTONS: The six numbered pushbuttons let
you return
to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear a chime. The sound will mute. When it
returns, release the button. Whenever you press that
numbered button, the station you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds until PRESET SCAN appears on the display to
listen to each of your preset stations for a few seconds
(factory presets which have not been reprogrammed
with your stations will be ignored). The radio will go
to the first preset station stored on your pushbuttons,
stop for a few seconds, then go on to the next preset
station. Press SCAN again
to stop scanning. If a preset
station has weak reception, the radio will not stop at the
preset station.
Setting the Tone
BASS: Press this knob lightly so it extends. Turn the
knob clockwise
to increase and counterclockwise to
decrease bass.
TREB: Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise to
decrease treble.
If a station is weak or noisy, you may
want to decrease the treble.
Push these knobs back into their stored positions
when
you’re not using them.
Adjusting the Speakers
BAL: Press this knob lightly so it extends. Turn the
knob clockwise to adjust sound to the right speakers
and counterclockwise for
the left speakers. The middle
position balances the sound between the speakers.
FADE: Press this knob lightly so it extends. Turn the
knob clockwise to adjust the sound to the front speakers
and counterclockwise for the rear speakers. The middle
position balances the sound between the speakers.
Push these knobs back into their stored positions when
you’re not using them.
3-11

Downloaded from www.Manualslib.com manuals search engine Playing the Radio
PWRNOL:
Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again to turn the system off. To increase volume, turn
the knob clockwise. Turn
it counterclockwise to
decrease volume. The volume level will appear on
the display.
Finding a Station
BAND:
Press this button to select AM, FM 1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek
to the next higher or lower radio station. Pressing and
holding this button until
a chime sounds puts the radio
in a tune mode. In this mode, higher or lower radio
stations are advanced to
in small increments until the
SEEK-TUNE button is released. Tuning stops when
you release this button. If
you press and hold the
SEEK-TUNE button again within five seconds
of being
in the tune mode, tuning will continue. Waiting longer
than five seconds places the radio back
in the seek mode.
SCAN: Press this button and SCAN will appear on the
display. Use SCAN to listen to stations for a few
seconds.
The radio will go to a station, stop for a few
seconds, then go on to the next station. Press this button
again to stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return
to your favorite stations. You can set up to
18 stations (six AM, six FM 1 and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FMl or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear a chime.
A preset number will appear on
the display. The sound will mute. When it returns,
release the button. Whenever you press that
numbered button, the station
you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds until PRESET SCAN appears on the display to
listen to each of your preset stations for a few seconds
(factory presets which have
not been reprogrammed
with your stations will be ignored). The radio will
go
to the first preset station stored on your pushbuttons,
stop for a few seconds, then go
on to the next preset
station. Press
SCAN again to stop scanning. If a preset
station has weak reception,
the radio will not stop at the
preset station.