1997 AUDI A4 engine

24-49

Test requirement:

Fuel pressure OK, checking Page 24
-32
.

Test sequence

- Remove fuel distributor including fuel injectors
from intake manifold Page 24
-45
. Fuel lines
remain connected.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

Checking Proper Seal

- Bridge terminals 1 and 65 at test box using wires
from VAG1594A adapter test kit.

- Switch ignition on.


Fuel Pump (FP) must run.

- Check proper seal of fuel injectors (visual
inspection). With Fuel Pump (FP) running, only 1
to 2 drops per minute may drip out per injector.

-
If fuel loss is greater, stop Fuel Pump (FP) from
Pa
ge 53 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-50

Checking Injection Quantity

- Insert fuel injector to be tested in a measuring
glass from VAG1602 injection quantity test
device.

- Connect one terminal of fuel injector to engine Ground (GND) using an
adapter cable and an alligator clip from VAG1594A connector test kit.
- Connect the second terminal of fuel injector to B+ using VAG1348/3A
remote control, VAG1348/3-2 adapter cable and assisting cable.
- Bridge terminals 1 and 65 at test box using wires from VAG1594A
adapter test kit.
- Bridge terminals 1 and 65 at test box using wires from VAG1594A
adapter test kit.
- Switch ignition on.

Fuel Pump (FP) must run.
- Activate VAG1348/3A remote control for 30 seconds.
- Perform measurement on all fuel injectors.
Pa
ge 55 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-53
Component location Overview of component
locations Page 24
-5
Voltage is supplied to the Fuel Pump (FP) and
several components of the injection system via
the Fuel Pump (FP) relay -J17-.
Engine must be turning for Fuel Pump (FP) relay
-J17- to close. This means that the relay does
not receive Ground (GND) (via ECM) until the
ECM recognizes RPM signals.

Test requirement:

Battery voltage at least 12.7 V

Function test of Fuel Pump (FP) relay

- Remove driver-side storage compartment.

Repair Manual, Body Interior, Repair Group
68


- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Ignition must remain switched on for this.

-
Initiate output Diagnostic Test Mode (DTM)
Page 01
-51
and activate Evaporative Emission
Pa
ge 58 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-55
If specified value is not obtained:

- Replace central electronics.

Checking activation of Fuel Pump (FP) relay

- Switch ignition off.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

- Switch ignition on.

- Bridge terminals 1 and 65 at test box using wires
from VAG1594A adapter test kit.

If relay triggers now, but didn't during output DTM:
If relay does not trigger:
Fuel Pump (FP) relay (at position 4 of central electronics in driver's
footwell, left) must trigger.
- Replace Engine Control Module (ECM) Page 24
-22
- Switch ignition off.
- Remove cable bridge.
Pa
ge 61 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-56


If specified value is not obtained:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
If specified value is obtained: - Connect multimeter for voltage measurement as follows.Central electronicsin driver-side footwell, left,
position 4
Terminal
Measure to
19 Engine Ground
(GND)
- Switch ignition on.

Specification: approx. battery voltage
- Check wire connections.
- Check the following wire connection for open circuit and short circuit to
Ground (GND) and B+: Central electronicsin driver-side footwell, left,
position 4
Terminal
VAG1598/31 test
box


Socket
Pa
ge 63 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-57

- Repair open circuit or short circuit if
necessary.
If no malfunctions are detected:

- Replace Fuel Pump (FP) relay -J17-.

- Re-connect Engine Control Module (ECM).

Check voltage supply for Fuel Pump (FP) and
components

- Remove fuses S228, S232, and S234 (positions 28, 32, and 34) from
fuse holder.
- Initiate output Diagnostic Test Mode (DTM) Page 01
-51
and activate
Evaporative Emission (EVAP) canister purge regulator valve -N80-.
- Connect multimeter for voltage measurement to Ground (GND) and to
one terminal of the following fuses in the fuse holder. Circlip
Specified value at one of the terminals
S228 approx. battery voltage
S232 approx. battery voltage
S234 approx. battery voltage
Pa
ge 65 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-60
Component location Overview of component
locations Page 24
-5

Test requirements:

Coolant Temperature at least 80 C.

Electrical consumers switched off (radiator
fan must NOT run during test).
A/C switched off.

Checking function

- Connect VAS5051 tester Page 01
-7 and
select vehicle system "01 - Engine electronics".
Engine must run at idle for this.

Display on VAS5051:
- In selection -1-, click on the diagnostic function "04 - Basic setting".
Pa
ge 68 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1

24-62


Display fields

1 2 3 4
Display group 002: Air mass taken in with engine at idle and operating temperature
Display xxx /min xxx %
xx.x ms
xxx.x g/s
Indicated Engine speed (RPM) Load
mean injection time
Air mass
Specified value FWD: 740 to 860 RPM
AWD: 820 to 880 RPM 15 to 35 %
1.0 to 4.0 ms
2.0 to 4.5 g/s
Note --- ---
If specified value is not obtained: Evaluation Page 24
-63

If specified value is obtained:

-
End function "04 - Basic setting" by pressing
button.
Pa
ge 70 of 79 Motronic in
jection s
ystem, servicin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.24.1