1997 AUDI A4 engine

28-48
If all specifications are reached but the diode test
lamp does not flash (measurement taken
between terminals 1 and 2 without unplugging
connector and while operating starter):

- Replace relevant Hall sensor.
If specifications are obtained:

- Check wiring.

Checking wiring between hall sensor and
engine control module

- Connect VAG1598/31 test box to wiring harness
for engine control module. Do not connect to the
engine control module itself Page 24
-20
.

- Check wiring connection from Hall sensor to engine control module for
open circuit and/or short circuit to B+ or Ground (GND).
Pa
ge 55 of 64 I
gnition s
ystem, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.28.1

28-50
If all the test results so far have been OK but a
malfunction related to the camshaft position
sensor (Hall sensor) is displayed again after
erasing the DTC memory as a test measure, the
following might be the cause:

- Rotor ring (trigger wheel) for camshaft position
sensor (Hall sensor) misaligned; test phase
position.

Checking phase position of Hall sensor

- Connect vehicle diagnostic, testing and
information system VAS5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page
01
-9 . When doing this the engine must be
idling.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select function "Read Measuring Value
Block" and confirm entry with -Q- button.
Read Measurin
g Value Block
Input displa
y group number XXX

Indicated on display:
- Press buttons -0-, -9- and -3- to select "Display Group 093" and
confirm entry with -Q- button.
Pa
ge 57 of 64 I
gnition s
ystem, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.28.1

28-51

Read Measuring Value Block 93
1
2
3
4

Indicated on display
- Check specified display values for Hall sensors.

Display fields

1 2 3 4
Display Group 093: Phase positions of Hall sensors (Bank 1 and Bank 2) with engine idling
Display xxx RPM xx %
0 6 KW
0 6 KW
Indicates Engine
speed
(RPM) Engine
load Phase position
Bank 1 Phase position
Bank 2
Work
range min.: 750
RPM
max.: 6800
RPM min.: 15
%
max.:
175 % -20.3 to 14.8 KW
-20.3 to 14.8 KW
Specified
value 750 - 850
RPM
0 6 KW
0 6 KW
Note
If readouts do not match specifications, unbolt Hall sensor and check whether
rotor ring is properly mounted on camshaft. If it is incorrectly mounted, the
locating lug will be flattened when the securing bolt is tightened. Also check
valve timing.
Repair Manual, 2.7 Liter V6 5V BiTurbo Engine Mechanical, Engine Code(s): APB,
Repair Group 13, Crankcase ventilation, Ribbed belt removing and installing, Timing belt removing and installing

Pa
ge 58 of 64 I
gnition s
ystem, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.28.1

28-52

Misfire recognition, checking


Test sequence

- Connect vehicle diagnostic, testing and
information system VAS5051 or VAG1551 scan
tool and select engine electronics control
module by entering address word "01" Page
01
-9 . When doing this the engine must be at
idle.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select function "Read Measuring Value
Block" and confirm entry with -Q- button.
Read Measurin
g Value Block
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -1- and -4- to select "Display Group 014" and
confirm entry with -Q- button.
Read Measuring Value Block 14
1
2
3
4

Indicated on display
- Check misfire recognition.
Pa
ge 59 of 64 I
gnition s
ystem, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.28.1

28-53


Display fields

1 2 3 4
Display Group 014: Misfire recognition
Display xxx / RPM xxx %
xxx
---
Indicated Engine speed
(RPM) Load
Sum of misfire
Misfire
recognition
Work range min.: 750 /
RPM
max.:
6800 /RPM min.: 0
max.:
100
activated
locked
Specified
value 650 - 720 /
RPM 15.0 -
22.0 % 0 - 15
activated
Note --- ---
If specified value is not reached: Evaluation display field
3 Page 28
-54
see also page Page 28
-55

---
If specified value is reached:

-
Press button.Rapid Data Transfer
HELP
Select function XX

Indicated on display (select function)
Pa
ge 60 of 64 I
gnition s
ystem, checkin
g
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.28.1