1997 AUDI A4 lock

13-1


Engine, disassembly and
assembly

Ribbed belt, removing and installing


Removing

Repair Manual, Body Exterior, Repair Group 63
- Remove noise insulation -arrows-.
- Remove bumper
- Move lock carrier to service position

Note:
Viscous fan has left-hand thread: turn in direction indicated. - Remove viscous fan (counter-hold with pin wrench 3212).
Pa
ge 1 of 13 En
gine, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.1

13-3

Installing

Routing of ribbed belt - Install ribbed belt onto crankshaft pulley and idler wheel first, and push
belt onto tensioning roller last.
D1 - vehicles without air conditionerD2 - vehicles with air conditioner
- Take out mandrel 3204.

Note:
Viscous fan has left-hand thread: turn against direction indicated.
Repair Manual, Body Exterior, Repair Group 50

Repair Manual, Body Exterior, Repair Group 63 - Counter-hold belt pulley for viscous fan using spanner wrench 3212
and tighten viscous fan using open end spanner 3312 and torque
wrench 1331 (left hand thread).
- Install lock carrier.
- Install bumper.- Install noise insulation.
Pa
ge 3 of 13 En
gine, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.1

13-6


Note:
Turn over the engine at the central bolt on the crankshaft.
CAUTION!
Injury risk - do not turn engine while feeling for TDC drilling. - Turn crankshaft to TDC by hand. Marks -A- and -B- must be aligned.
- Check position of camshafts: larger holes in securing plates on
camshaft sprockets must align opposite one another on inside. If not,
turn crankshaft one revolution further.
- Remove sealing plug from cylinder block, left.
- The TDC drilling in the crankshaft must be visible (or able to be felt) in
line with the sealing plug hole.

- Screw clamping bolt 3242 for crankshaft into sealing plug hole and
tighten.
Pa
ge 6 of 13 En
gine, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.1

13-8

Note:

Mark the direction of rotation of the toothed belt
with chalk or felt pen before removing. A used
belt can break if it rotates in the wrong direction
when reinstalled.
The toothed belt tensioning element is oil-
damped and can therefore only be compressed
slowly by applying constant pressure.

- Using a hex key, turn toothed belt tensioning roller -1- clockwise 8 mm
in direction of arrow until tensioning lever -2- compresses tensioning
element -3- sufficiently to enable special tool T 400 11 to be fitted in
drilling and in plunger.
- Insert special tool T 400 11, release toothed belt tensioning roller.
- Take off toothed belt.
Pa
ge 8 of 13 En
gine, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.1

13-10


- Using a hex key, turn toothed belt tensioning roller -1- clockwise 8 mm
in direction of arrow until special tool T 400 11 can be removed.

- Pre-tension toothed belt by a turning in direction of arrow with a torque
of 15 Nm using a torque wrench.
- Tighten bolts on camshaft sprockets.
Pa
ge 10 of 13 En
gine, disassembl
y and assembl
y
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.13.1