1997 AUDI A4 ESP

01-164

Display
field Specified display
value Corresponds to physical
values Designation and conversion to physical values
9 3 Oxygen sensor learning requirement at idle and partial
throttle range,
0 = Oxygen sensor learning requirement at idle and
partial throttle range
3 = Oxygen sensor learning process at idle completed
10 50 - 100 250 - 500 mV Throttle Position (TP) sensor -G69- learning value,
display X 5 = ...mV Note on display field 9:
If specified display values are greater than 3, display groups 007 and/or 008.
Pa
ge 229 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-183
Notes on display field 1 (cont'd):
The oxygen sensor control stop evaluation is also done by the diagnosis only after successful learning learning
requirement display:
Control stop max.: + 32%
Control stop min.: - 87.5%
With values of more than 20% in "Basic Setting" function 04, the following malfunctions are possible: Intake air leaks
Engine damage (oil burning with faulty piston)
Notes on display field 2:
In display field 2 (learning range display), the momentary learning range (load status) is displayed. Only idle and partial
throttle learning ranges are displayed since, at wide open throttle, no learning takes place.
In order to reach the corresponding learning range (load status):
Idle: the vehicle should be allowed to run at idle (650-900 RPM)
Partial throttle 1, 2 or 3: during test drive (with second person), increase engine speed to 1500-3000 RPM and generate
load by lightly operating the brake
X
X
X
X
Meaning of 4-digit learning range display
Pa
ge 256 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-184
Notes on display field 3

The oxygen sensor learning requirement diagnosis shows what oxygen sensor learning value was checked in the learning
process.
If diagnosis is successful, the corresponding value is set to "1", independently of whether the diagnosis was recognized as
OK or not OK.
If an "oxygen sensor learning requirement diagnosis" value is set to "1" in display field 3, but the corresponding value of
the "oxygen sensor learning requirement display" is not set to "1" in display field 4, the diagnosis was carried out but not
recognized as OK by the Engine Control Module (ECM). The " oxygen sensor learning requirement diagnosis" is now
continued.
The oxygen sensor learning requirement diagnosis is reset to "0" every time there is a start with a coolant temperature
less than 40 C (104 F).
X
X
X
X
X
X
X
X
Meaning of 8-digit oxygen sensor learning requirement diagnosis

1 = Idle (bank 1)

2 = Idle (bank 2)

3 = Partial throttle 1 (bank 1)

4 = Partial throttle 1 (bank 2)

5 = Partial throttle 2 (bank 1)

6 = Partial throttle 2 (bank 2)

7 = Partial throttle 3 (bank 1)
Pa
ge 258 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

During "Basic Setting" function 04 with VAG 1551 scan tool and/or each time the DTC memory is erased, all learning
requirement displays are set to 0 in order to force new learning of the oxygen sensor learning values after the shop visit.
At each start, coolant temperature less than 40 C (104 F), the learning requirement is forced in all learning ranges. If there is a large learning value deviation (from the stored learning value to the newly learned value) in the learning
process, all learning requirement displays are reset to 0.
If there is successful learning, the learning requirement values of the respective learning ranges (display field 2) are set to 1.
Pa
ge 261 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-212
If the trip status display is set to "1" when the readiness code is regenerated, but the corresponding display value of the
readiness code is not set to "0", the diagnosis was carried out but recognized as not OK by the engine control module. In this
case, the DTC memory should be checked to determine malfunctions and/or to carry out a selective diagnosis:

For three way catalytic converter diagnosis (Bank 1 and 2) also check display groups 035, 036 and 044.
For the Evaporative Emissions (EVAP) system leak diagnosis, also check display group 030.
For the Secondary Air Injection (AIR) system throughput and leak diagnosis, also check display groups 020 and 021.
For oxygen sensor diagnosis, also check display groups 032, 033, 034, 041, 042 and 043.
For oxygen sensor heating diagnosis, also check display group 040.
For the Exhaust Gas Recirculation (EGR) system throughput diagnosis, also check display group 017.
Display
shows Display specified
value Designation/diagnosis
Basic setting
29
1 2 3 4 X X X X X X 1 = Readiness Code
X X X X X X X X 2 = Trip Status display
0 - 40 3 = Counter for warm-up phases without new malfunctions except for "combustion
misfiring" and/or "oxygen sensor control"
0 - 40 4 = Counter for warm-up phases without new malfunctions except for "combustion
Pa
ge 301 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-215
Notes on display fields 3 and 4:

Display field 3 evaluates all malfunctions except "Combustion misfiring and oxygen sensor control."
Display field 4 evaluates only the malfunctions "Combustion misfiring and oxygen sensor control"
If a malfunction is recognized, the corresponding counter will be set to "40." The counter is decremented, during a new
start, when the trip was started at coolant temperature of 49 C (120 F) and ended at a water temperature of 71 C
(160 F) and the malfunction is no longer recognized. However, decrementing is only allowed if the MIL has not lit up yet
or is no longer lit. When counter status "0" is reached, the recognized malfunction is erased. If the DTC memory is erased, the counter is also decremented.
Pa
ge 306 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-220
Display group 032 [Longest and shortest flank rise and flank fall time (response time) of the voltage signal for bank 1
heated oxygen sensor 1]
Display group 033 [Longest and shortest flank rise and flank fall time (response time) of the voltage signal for bank 2
heated oxygen sensor 2]
Display group 034 [Number of flank rise and flank fall tests]
Notes on display group 032, 033 and 034:

If the value of the heated oxygen sensor diagnosis is not set to "0" in display group 029, display field 1 during regeneration
of the readiness code, and/or there is a malfunction in the DTC memory that relates to the heated oxygen sensors, display
groups 032, 033 and 034, as well as display groups 042 and 043 are used to carry out a selective diagnosis.
The Engine Control Module (ECM) checks the flank rise and/or flank fall time (response time) of the voltage signal for the
heated oxygen sensors in front of three way catalytic converter after every start with diagnostic conditions fulfilled
display group 042. The display values for display group 034 are incremented with each diagnosis that is carried out, whether the diagnosis is
recognized as OK or not OK. If the flank rise and/or flank fall time is recognized as OK during the first diagnosis, the
display values are increased by the value "1" and the diagnosis is discontinued. If the limit values (flank rise time 90
ms/flank fall time 85 ms) are exceeded, the diagnosis is recognized as not OK. The flank rise and/or fall times now
continue to be checked, whereby the display values are incremented with each additional diagnosis. However, the limit
values can also be exceeded because combustion misfiring is recognized. In this case, the malfunction "Bank X probe Y
signal too slow" is not stored in DTC memory, but" Cyl. x Combustion misfiring recognized" is stored.
Pa
ge 313 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-233
Display group 042 [Diagnostic conditions for diagnosis of the flank rise and/or flank fall time (response time) of the
voltage signal of heated oxygen sensors in front of three way catalytic converters]
Notes:

If the value of the oxygen sensor diagnosis is not set to "0" in display group 029, display field 1 during regeneration of the
readiness code and/or there is a malfunction in DTC memory that relates to the oxygen sensor, display group 042 can be
used to set up the diagnostic conditions (display fields 3 and 4) and the diagnostic result (display field 2) can be read.
If the diagnostic conditions are fulfilled, the Engine Control Module (ECM) checks the flank rise and/or flank fall time
(response time) of the voltage signal of the heated oxygen sensors in front of the three way catalytic converters at each
start, which is displayed each time display groups 032, 033, 034 and 43 are displayed.
The diagnostic conditions are only fulfilled during a trip of approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with
manual transmission in 4th or 5th gear, or automatic transmission selector lever in "D" position, preferably in 4th gear. If
the diagnostic conditions are fulfilled, diagnosis is active. In order to get a diagnosis result, you have to drive approx. 1-1/2
to 5 minutes under diagnostic conditions.
If a malfunction is stored in DTC memory, which affects diagnostic conditions 1 and 2, the diagnostic conditions can not be
achieved. In this case repair the malfunction "DTC memory, checking and erasing page 01
-13
.
If a malfunction is stored that involves the heated oxygen sensors in front of three way catalytic converters, the diagnostic
conditions can be achieved, but the diagnosis result can not be OK.
If the flank rise and flank fall time is recognized as OK during the first diagnosis, the diagnosis is discontinued. If the times
are recognized as not OK, the diagnosis of the flank rise and/or flank fall time is continued. If the diagnosis will be
repeated selectively or after an OK diagnosis, switch engine off and restart.
Pa
ge 328 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1