1997 AUDI A4 display

01-217

Display shows
Display/specified value
Designation/diagnosis
Basic setting 30
1 2 3 4 -- mbar 1 = Currently measured EVAP system under pressure
-- mbar 2 = Currently calculated EVAP minimum under pressure
0 - 99% 3 = Duty cycle (triggering) EVAP canister purge regulator valve
0% = completely open
99% = completely closed
X X X X X 4 = Diagnosis status and/or result Note on display field 2:
An under pressure calculated from the momentary throughput of the Mass Air Flow (MAF) sensor (intake air mass) is
displayed.
Notes on display field 4:
0 1 X X X = Diagnosis carried out, diagnosis OK
1 0 X X X = Diagnosis carried out, malfunction recognized, diagnosis is continued
The display positions marked with X do not have to be fulfilled to evaluate the diagnostic status and/or result.
Pa
ge 309 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-218

X
X
X
X
X
Meaning of 5-digit "Diagnostic Status and/or Result"

1 = Diagnostic conditions during test drive (approx. 1-1/2 to 5 minutes at 80-100 km/h (50-63 mph) with
manual transmission in 4th or 5th gear, or automatic transmission selector lever in "D" position, preferably
in 4th gear)
Manual transmission: 8 - 45%
Automatic Transmission: 8 - 20%
Value "0" = Diagnostic conditions not fulfilled
Value "1" = Diagnostic conditions fulfilled
Engine speed: 1600 RPM - 4500 RPM ( display group 003) Intake air through Mass Air Flow (MAF) sensor: 22 g/sec - 56 g/sec ( display group 019) Throttle angle: ( display group 003)

2 = Pressure measurement w/EVAP canister purge regulator valve completely closed
Value "0" = Pressure measurement not completed yet
Value "1" = Pressure measurement completed

3 = Pressure measurement w/EVAP canister purge regulator valve completely open
Value "0" = Pressure measurement not completed yet
Value "1" = Pressure measurement completed

4 = Diagnostic status
Pa
ge 310 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-219
Display group 031 (Operating conditions when combustion misfiring is recognized):
Notes:

If the malfunction "Combustion misfiring recognized" and "Cyl. X Combustion misfiring recognized" are stored in DTC
memory, display groups 031, 037, 038 and 039 are used to carry out a selective diagnosis.
Display group 031 shows the operating conditions that are present at the moment the malfunction is recognized. However,
the operating conditions are only displayed if combustion misfiring is recognized by the Engine Control Module (ECM) and
stored in DTC memory. If there is more combustion misfiring that has to be displayed, the operating conditions of the most
recently recognized combustion misfiring is displayed.
If the malfunction "Combustion misfiring" is stored in the DTC memory, at the same time a counter is set to the value of
"40". This counter is displayed under display field 4 when display group 029 is called. If combustion misfiring is no longer
recognized during the next 40 warm-up phases, the malfunctions in DTC memory and the operating conditions are
erased.
Display shows
Display specified value
Designation/diagnosis
Basic setting 31
1 2 3 4 ... RPM 1 = Lowest engine speed at which combustion misfiring was recognized
... RPM 2 = Highest engine speed at which combustion misfiring was recognized
__._% 3 = Lowest engine load at which combustion misfiring was recognized
__._% 4 = Highest engine load at which combustion misfiring was recognized
Pa
ge 312 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-220
Display group 032 [Longest and shortest flank rise and flank fall time (response time) of the voltage signal for bank 1
heated oxygen sensor 1]
Display group 033 [Longest and shortest flank rise and flank fall time (response time) of the voltage signal for bank 2
heated oxygen sensor 2]
Display group 034 [Number of flank rise and flank fall tests]
Notes on display group 032, 033 and 034:

If the value of the heated oxygen sensor diagnosis is not set to "0" in display group 029, display field 1 during regeneration
of the readiness code, and/or there is a malfunction in the DTC memory that relates to the heated oxygen sensors, display
groups 032, 033 and 034, as well as display groups 042 and 043 are used to carry out a selective diagnosis.
The Engine Control Module (ECM) checks the flank rise and/or flank fall time (response time) of the voltage signal for the
heated oxygen sensors in front of three way catalytic converter after every start with diagnostic conditions fulfilled
display group 042. The display values for display group 034 are incremented with each diagnosis that is carried out, whether the diagnosis is
recognized as OK or not OK. If the flank rise and/or flank fall time is recognized as OK during the first diagnosis, the
display values are increased by the value "1" and the diagnosis is discontinued. If the limit values (flank rise time 90
ms/flank fall time 85 ms) are exceeded, the diagnosis is recognized as not OK. The flank rise and/or fall times now
continue to be checked, whereby the display values are incremented with each additional diagnosis. However, the limit
values can also be exceeded because combustion misfiring is recognized. In this case, the malfunction "Bank X probe Y
signal too slow" is not stored in DTC memory, but" Cyl. x Combustion misfiring recognized" is stored.
Pa
ge 313 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-221

Display groups 032 and 033 show the highest and lowest flank rise and/or flank fall time for all tests carried out (number of
tests display group 034). If during one of the next tests, a higher or lower diagnosis time is recognized, the current value is overwritten. With
diagnostic conditions fulfilled, display group 043 shows the current flank rise and flank fall times. After diagnosis is ended,
the diagnosis times shown are those that were recognized at the last diagnosis that was carried out.
The display values are only reset by erasing the DTC memory. Selective observation times can be defined by resetting the
display values.
Display shows
Display specified value
Designation/diagnosis
Basic setting 32
1 2 3 4 0.0 - 260.0 ms 1 = Highest flank rise time, bank 1, heated oxygen sensor 1
(limit value: 90 ms)
0.0 - 260.0 ms 2 = Lowest flank rise time, bank 1, heated oxygen sensor 1
(limit value: 90 ms)
0.0 - 260.0 ms 3 = Highest flank fall time, bank 1, heated oxygen sensor 1
(limit value: 100 ms)
0.0 - 260.0 ms 4 = Lowest flank fall time, bank 1, heated oxygen sensor 1
(limit value: 100 ms)
Pa
ge 314 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-222

Display shows
Display specified value
Designation/diagnosis
Basic setting 33
1 2 3 4 0.0 - 260.0 ms 1 = Highest flank rise time, bank 2, heated oxygen sensor 1
(limit value: 90 ms)
0.0 - 260.0 ms 2 = Lowest flank rise time, bank 2, heated oxygen sensor 1
(limit value: 90 ms)
0.0 - 260.0 ms 3 = Highest flank fall time, bank 2, heated oxygen sensor 1
(limit value: 100 ms)
0.0 - 260.0 ms 4 = Lowest flank fall time, bank 2, heated oxygen sensor 1
(limit value: 100 ms) Display shows
Display specified value
Designation/diagnosis
Basic setting 34
1 2 3 4 0 - 255 1 = Number of flank rise tests, bank 1, heated oxygen sensor 1
0 - 255 2 = Number of flank fall tests, bank 1, heated oxygen sensor 1
0 - 255 3 = Number of flank rise tests, bank 2, heated oxygen sensor 1
0 - 255 4 = Number of flank fall tests, bank 2, heated oxygen sensor 1
Pa
ge 315 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-223
Display group 035 (Three way catalytic converter diagnosis, bank 1)
Display group 036 (Three way catalytic converter diagnosis, bank 2)
Notes on display groups 035 and 036:

If the value of the three way catalytic converter diagnosis is not set to "0" in display group 029, display field 1 during
regeneration of the readiness code and/or there is a malfunction in DTC memory that relates to the three way catalytic
converter, display groups 035, 036 and 044 are used to carry out a selective diagnosis.
At each start, when the diagnostic conditions are fulfilled ( display group 044) the Engine Control Module (ECM) checks
the deterioration rate of the three way catalytic converter by the heated oxygen sensors in front of and behind the three
way catalytic converter. Display fields 1 and 2 display the largest and smallest rate of deterioration of all the diagnoses carried out. If a higher or
lower rate of deterioration is recognized at the next diagnosis, the current value is overwritten.
The number of three way catalytic converter diagnoses (display field 3) is incremented each time a diagnosis is carried
out, no matter whether the diagnosis is considered OK or not OK.
If the rate of deterioration is recognized as OK during the first diagnosis, the number of three way catalytic converter
diagnoses is increased by the value of "1" and the diagnosis is discontinued.
If the limit value of 50% is exceeded, the diagnosis is recognized as not OK. In this case, the rate of deterioration
continues to be checked, while the number of three way catalytic converter diagnoses is incremented with each additional
diagnosis.
Display field 4 shows the current rate of deterioration recognized at the last diagnosis.
Pa
ge 316 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

The display values are only reset by erasing the DTC memory. Selective observation time periods can be defined by
resetting the display values.
Pa
ge 317 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1