Page 1 of 12
19-3
 
  
Cooling system, components Note: 
 
Always replace gaskets and seals.
 Draining and filling system with coolant   page 19
-6 . 
 Testing cooling system for leaks   page 19
-11
 .
1 - 
Thermostat 
Replacing  page 19
-4
Opening and closing temperatures   page 19
-4 
2 - 
Seal 
Always replace
3 - 
Thermostat housing 
4 - 
10 Nm (7 ft lb) 
5 - 
Gasket Always replace
6 - 
Coolant pump To remove and install, remove ribbed drive 
belt (   page 13
-9 ) and toothed belt (   
page 13
-11
 ) 
7 - 
10 Nm (7 ft lb) 
Pa
ge 1 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2 
         
        
        
     
        
        Page 4 of 12
19-6
      
Cooling system, draining and filling
 
     
Note:  
     
The cooling system is filled year round with a 
mixture of water and anti-freeze and anti-
corrosion agent G 011 A8C. 
     G 011 A8C and coolant additives marked with 
"conforming to TLVW 774 C" prevents freezing, 
corrosion damage and scale formation, and 
raises the coolant boiling point. For these 
reasons the cooling system must always be 
filled year-round with G 011 A8C anti-freeze 
and anti-corrosion agent. 
     Due to its high boiling point, coolant is an aid to 
operational efficiency when the engine is 
operating at full load, particularly in tropical 
climates. 
     Coolant must be drained and replaced if either 
the radiator, heater core, cylinder head or 
cylinder head gasket have been replaced. 
     Capacity: approx. 8.5 liters (9 qt.)
     
Draining  
     
WARNING! 
Pa
ge 4 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2 
         
        
        
     
        
        Page 5 of 12
     
The cooling system is pressurized when the 
engine is warm. Wear gloves and other 
appropriate protection, and slowly and 
carefully release system pressure, if 
necessary, before performing repairs. 
Pa
ge 5 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2 
         
        
        
     
        
        Page 7 of 12
19-8
 
    
Filling  
Recommended mixing ratios:  1) Do not exceed an antifreeze concentration of 60%; antifreeze protection 
and cooling efficiency are reduced if the concentration is higher.  2) The quantity of coolant may differ depending on specific equipment 
installed in the vehicle.  -  Using special tool 3247, drain coolant from engine drain plug (arrow) 
and at drain plug on bottom left of radiator. Anti-freeze protection 
down to:  Anti-freeze 
concentration
1)  G 11
2)  
Water
2)  
-25 C (-13 F)  
40%   2.5 
liter 
(2.6 
qt.)  3.5 liter
(3.7 qt.)  
-35 C (-31 F)  50%   3.0 
liter 
(3.2 
qt.)  3.0 liter
(3.2 qt.)  
Pa
ge 7 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2 
         
        
        
     
        
        Page 10 of 12
19-10
      
WARNING! 
     
The cooling system is pressurized when the 
engine is warm. Wear gloves and other 
appropriate protection, and slowly and 
carefully release system pressure, if 
necessary, before performing repairs. 
     
-  Check coolant level in expansion tank and top 
up if necessary. 
     
-  Stop engine (switch ignition off).
Pa
ge 10 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2 
         
        
        
     
        
        Page 11 of 12
19-11
      
Cooling system leaks, checking
 
     
WARNING! 
     
The cooling system is pressurized when the 
engine is warm. Wear gloves and other 
appropriate protection, and slowly and 
carefully release system pressure, if 
necessary, before performing repairs. 
     
Engine must be at operating temperature 
    
If the pressure drops:  -  Connect cooling system tester VW 1274 to expansion tank using 
adapter VW 1274/1. 
-  Operate hand pump on tester to create a pressure of approx. 1 bar (15 
psi). 
-  Locate and repair leak in the cooling system.
Pa
ge 11 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2 
         
        
        
     
        
        Page 12 of 12
19-12
      
Expansion tank cap, pressure testing
 
    
-  Screw cap onto cooling system tester VW 1274 with adapter VW 
1274/1. 
-  Operate hand pump to build pressure.
-  Pressure relief valve must open at 1.2-1.5 bar (17-22 psi).
Pa
ge 12 of 12 Coolin
g system, com
ponents
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE01.19.2