1997 AUDI A4 torque

01-191

Indicated on display (example)

Display fields:
1 2 3 4

Display group no.
Display field
Description
Read measuring value block 7

21.0 C 0.747A TC on 0 RPM
007 1
2
3
4 ATF temperature
Specified current of solenoid valve 7 -N94-
Torque converter clutch
Torque converter slip speed
Read measuring value block 8

0 % 5 % 008 1
2
3

4 Kick down switch
Throttle valve value
Engine torque in Nm
1)
Throttle valve duty cycle in %
2)
Deceleration mode/engine under load
Read measuring value block 9

100 Nm 350 Nm 0 RPM 0%
009
1)
1
2
3
4 Engine torque (actual)
Maximum torque
Engine speed (RPM)
Throttle valve value
Pa
ge 6 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-192

Indicated on display (example)

Display fields:
1 2 3 4

Display group no.
Display field
Description
Read measuring value block 9

100 Nm 0 RPM 0 % 0.00 ms
009
2)
1
2
3
4 Engine torque (actual)
Engine speed (RPM)
Throttle valve value
Fuel consumption signal
Read measuring value block 10

0,00 0 RPM 4
010 1
2
3
4 Torque increase in torque converter
Engine speed (RPM)
Gear selected
Anti-Slip Regulation (ASR)
Read measuring value block 11

D M-switch up button Compr. ON 011 1
2
3
4 Selector lever position
Tiptronic recognition
Tiptronic Switch -F189-
Air conditioning kick down
2) Only for vehicles without CAN-bus For information on which vehicles are equipped with CAN-bus
Pa
ge 8 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-215
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec.
value on
V.A.G
1551
display Corrective actions
007 1 ATF temperature
While standing with engine
running. When temperature
sensor is faulty, a replacement
value is transmitted. ... C
- Check Transmission Fluid
(ATF) Temperature sensor -
G93-; perform electrical test
page 01
-273


2 Specified current
of solenoid valve 7
-N94-
2) While driving
1)
min. 0.1 A
- See DTC table, DTC 270
page 01
-45



max 0.8 A
- Perform electrical test
page 01
-273


3 Torque converter
lock-up clutch While driving
1)
TC open
- See DTC table, DTC 1192
page 01
-45



TC control
- Perform electrical test
page 01
-273

Continue


TC closed
Pa
ge 35 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-216
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec. value on
V.A.G 1551
display Corrective actions
007
4 Torque
converter slip
speed hile
driving
1) TC open 0......standstill
RPM
- See DTC table, DTC 00297,
00660 and 01192 page 01
-45



TC control (last
shift operation at
least 20 sec ago) 20...120 RPM
Repair Manual, 5 Spd.
Automatic Transmission 01V, Repair Group 37, transmission with shift elements
- Determine which element is
faulty or not activated,
transmission with shift elements

TC closed 0...10 RPM
- Check plausibility between
engine, transmission input- and
transmission speed; Display
group number 001
1) While driving, a second mechanic is required to read specifications.
Notes for display field 4 of display group number 004 are on the next page:
Pa
ge 37 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-217
Test requirements for torque converter slip speeds:

"TC closed": Shifting process must be complete (wait at least 1 sec.), the Torque Converter (TC) must be closed and the
accelerator pedal value must be constant.
"TC control": Indicated values are valid for the regulating condition of the throttle converter (control). Under inconvenient
conditions (e.g. accelerating on a hill), this condition is not reached until 20 seconds after the shifting process has been
completed. During this regulating phase, slip values of up to 350 RPM can be reached.
Excessive torque slip speeds can also indicate slipping clutches or non-activated shifting elements.
Pa
ge 38 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-219
Only for transmission with hydraulic control -E17-
Display
group No. Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
008
3
3)

without
CAN-
bus Throttle valve
duty cycle While
standing idle smaller than
30% When accelerating from idle to Wide Open
Throttle (WOT), %-value increases
steadily.


Wide Open
Throttle
(WOT)
more than
70% - Perform electrical test page 01
-273
- See DTC table, DTC 00518 and 00638
page 01
-45


Continue

3
2)

with
CAN-
bus Engine torque
While driving
1)
Nm
The signal for actual engine torque is
transmitted by the Engine Control Module
(ECM) to the Transmission Control Module
(TCM) via the CAN-bus wiring.
Notes and footnotes for display group number 008 are on the next page.
Pa
ge 40 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-221
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
009

with
CAN-bus 1 Engine torque
(actual) while driving
1)
...Nm
The signal for actual engine torque is
transmitted by the Engine Control Module
(ECM) to the Transmission Control Module
(TCM) via the CAN-bus wiring.

2 Maximum
torque while driving 1)
...Nm
The engine torque required (reduced) by
the TCM during the shifting process
2)

3 Engine RPM with engine running approx.
0...8200
RPM - See DTC table, DTC 529 and 543
page 01
-45


4 Throttle valve
value while
standing Idle
1)
0...1 % When accelerating from idle to WOT, %-
value increases steadily.


Wide Open
Throttle
(WOT)
99...100 % - See DTC table, DTC 518 page 01
-45
Pa
ge 42 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-222
1) While driving, a second mechanic is required to read specifications. 2) While driving in one gear, the indicated shifting torque remains constantly high, since no torque reduction is required.
Notes for display group number 009;
This display group number 009 is only valid for vehicles with CAN-bus, refer to display group number 009 on next page for
vehicles without CAN-bus. A)
A) There is a distinction made between vehicles with and without CAN-bus. For information on which vehicles are equipped
with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

Pa
ge 44 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13