1996 VOLKSWAGEN PASSAT transmission

Downloaded from www.Manualslib.com manuals search engine 40-72

- Disconnect drive axle from transmission drive
flange. - Mark installation position of bolts (arrows) and
remove. Installing - Swing wheel outward (if necessary, place block of
wood or equivalent between strut and wheel
housing as shown).
- Push engine/transmission assembly toward front
and remove drive axle.
- Install in reverse order of removal. Page 72 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1

Downloaded from www.Manualslib.com manuals search engine 42-42
Removing and installing viscous coupling
Repair Manual, 5 Spd. Manual Transmission 02A; Repair Group 39
Tightening torque -A-: 45 Nm (33 ft lb) Fig. 9 Final drive, removing and installing
from axle beam Page 10 of 13Rear axle, servicing (four wheel drive vehicles)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.3

Downloaded from www.Manualslib.com manuals search engine 42-50

11 - Circlip Always replace Insert in shaft groove 12 - Outer constant velocity joint: 81 mm diameter Only replace complete Removing Page 40-54 Installing: drive onto
shaft with plastic
hammer until
compressed circlip
seats Greasing Notes
Page 42-46 Checking Page 40-60 13 - Inner support rings Prevents boot inflating Only installed on left
drive shaft
transmission end Page 5 of 7Rear drive shafts, servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.42.4

Downloaded from www.Manualslib.com manuals search engine 46-42

Repair Manual, 5 Spd. Manual Transmission 02A, Repair Group 30
Repair Manual, 5 Spd. Manual Transmission 02A, Repair Group 30 6 - Brake pedal return
spring
7 - Return spring
mounting tube
8 - Brake pedal mounting
bushing
9 - Brake pedal
10 - Clutch pedal Removing and
installing 11 - Pedal cluster mounting bracket
12 - Clutch pedal pivot pin
13 - Clutch pedal mounting
bushing
14 - Over-center spring
mounting
15 - Over-center spring Before removing,
remove clutch pedal Page 6 of 9Parking brake lever assembly overview12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.6

Downloaded from www.Manualslib.com manuals search engine 48-17
Instead of plastic sealing plugs a plug consisting of
Part No.113 301 229 A and banjo bolt, Part No. N
904 674 01 can be used. But when using these,
several 16 mm diameter sealing rings must be used
so that the holes in the banjo bolt are sealed. - Support engine/transmission assembly with 10-
222 A and 10-222 A/1 (support VR6 engine with
10-222A and 10-222A/3).
- Remove boot from seat on steering gear. - Remove subframe bolts. - Lower engine/transmission assembly; this will pull
the two halves of the universal joint apart.
- Disconnect hoses from steering gear and seal with plastic bag and adhesive tape.
- Seal power steering gear threaded holes with
plastic sealing plugs.
- Remove steering gear securing nuts (bolts remain
in subframe).
- Remove steering gear rearward. Page 17 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-18

Installing
Install in reverse order.

- Check position of steering wheel and, if
necessary, align front end.

Note: Tightening torques: When lifting the engine/transmission assembly
guide the lower half of the universal joint shaft -A-
into the upper half -B- at the same time (second
mechanic necessary). Coat boot with lubricant, e.g. soft soap, before
pulling onto steering gear.
Universal joint shaft 25 Nm (18 ft lb) halves
Steering gear 30 Nm (22 ft lb)
Tie rod joint 35 Nm (26 ft lb)
Subframe front and rear
70 Nm (52 ft lb) and turn 90 further Rear subframe bracket 65 Nm (48 ft lb) Page 18 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-86

1 - Cooling line Secured to
crossmember item
9 2 - Bracket Various versions
depending on
engine/transmission Page 48-96 3 - Pressure line
4 - Suction line Hydraulic pump -
Cooling line
5 - Hose clamp, 3 Nm (27
in lb)
6 - Hydraulic pump With V-belt pulley 7 - Hydraulic pump With ribbed belt
sprocket
8 - O-ring Always replace Page 86 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-94

Assembly overview:
Pressure and cooling
lines (vehicles with VR6
engine)
Note:
Securing of pressure line
varies according to type of
transmission Fig. 1 and
Fig. 2 1 - Reservoir
2 - Suction hose Reservoir - Cooling
line
3 - Cooling line Secured to
crossmember item
8 4 - Pressure line
5 - Suction line Cooling line -
Hydraulic pump
6 - Hose clamp, 3 Nm (27
in. Ib) Page 94 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1