1996 TOYOTA TERCEL light

DI-12
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
TOYOTA Enhanced Signals:
TOYOTA hand-held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.66 - 3.9 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio
Opening ratio rotary solenoid type IAC valveIdling: 25.5 - 43 %
STARTER SIGStarter SignalCranking: ON
CTP SIGClosed Throttle Position SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N position: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1, CYL#2, CYL#3, CYL#4Abnormal revolution variation for each cylinder0%
IGNITIONTotal number of ignition for every 1,000 revolu-
tions0 - 2,000 rpm
FUEL PUMPFuel Pump SignalIdling: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 - 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from lean to rich.
Idling after warmed up: 0 - 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1 Re-
sponse time for oxygen sensor output to switch
from rich to lean.
Idling after warmed up: 0 - 1,000 msec.
*: If no conditions are specifically stated for ºldlingº, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

DI4LF-02
- DIAGNOSTICSENGINE
DI-13
1996 TERCEL (RM440U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below, for details of each code, turn to the page referred to under the ''See page '' for the respec-
tive ''DTC No.'' in the DTC chart.
SAE Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P0105
(DI-20)
Manifold Absolute
Pressure/Barometric
Pressure Circuit
MalfunctionOpen or short in manifold absolute pressure sensor circuit
Manifold absolute pressure sensor
ECM

P0106
(DI-23)
Manifold Absolute
Pressure/Barometric
Pressure Circuit
Range/Performance Problem
Manifold absolute pressure sensor
P0110
(DI-24)Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM

P0115
(DI-28)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM

P0116
(DI-32)Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
Cooling system
P0120
(DI-33)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM

P0121
(DI-37)Throttle/Pedal Position
Sensor/Switch ºAº Circuit
Range/Performance Problem
Throttle position sensor
P0125
(DI-38)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in oxygen sensor circuit
Oxygen sensor
P0130
(DI-41)Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
Fuel trim malfunction
P0133
(DI-44)Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Oxygen sensor
P0136
(DI-45)Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor
P0141
(DI-47) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)Open or short in heater circuit of heated oxygen sensor
Heated oxygen sensor heater
ECM

*: 


MIL lights up

DI-14
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)DTC No.
(See Page)
Detection ItemTrouble AreaMIL*Memory
P0171
(DI-49)System too Lean
(Fuel Trim)
Air intake (hose loose)
Fuel line pressure
Injector blockage
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0172
(DI-49)System too Rich
(Fuel Trim)
Fuel line pressure
Injector blockage, leak
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0300
(DI-52)Random/Multiple Cylinder
Misfire DetectedIgnition system
Injector
FlliP0301
P0302
P0303
P0304
(DI-52)Misfire Detected
- Cylinder 1
- Cylinder 2
- Cylinder 3
- Cylinder 4Fuel line pressure
Compression pressure
Valve clearance not to specification
Valve timing
Manifold absolute pressure sensor
Engine coolant temp. sensor

P0325
(DI-57)Knock Sensor 1 Circuit
MalfunctionOpen or short in knock sensor 1 circuit
Knock sensor 1 (looseness)
ECM

P0335
(DI-60)Crankshaft Position Sensor
Circuit ºAº Malfunction
Open or short in crankshaft position sensor circuit
Crankshaft position sensor
Starter
ECM

P0340
(DI-63)Camshaft Position Sensor
Circuit Malfunction
Open or short in camshaft position sensor circuit
Camshaft position sensor
Starter
ECM

P0420
(DI-73)Catalyst System Efficiency
Below ThresholdThree-way catalytic converter
Open or short in (heated) oxygen sensor circuit
(Heated) oxygen sensor

P0500
(DI-76)Vehicle Speed Sensor
Malfunction
Open or short in vehicle speed sensor circuit
Vehicle speed sensor
Speedometer cable
ECM

P0505
(DI-78)Idle Control System
Malfunction
IAC valve is stuck or closed
Open or short in IAC valve circuit
Open or short in AC1 switch circuit
Air intake (hose loose)

*: 


MIL lights up

- DIAGNOSTICSENGINE
DI-15
1996 TERCEL (RM440U)
Manufacturer Controlled:
DTC No.
(See Page)Detection ItemTrouble AreaMIL*Memory
P1300
(DI-84)Igniter Circuit Malfunction
Open or short in IGF or IGT circuit from igniter to ECM
Igniter
ECM

P1335
(DI-89)Crankshaft Position Sensor
Circuit Malfunction
(during engine running)Open or short in crankshaft position sensor circuit
Crankshaft position sensor
ECM
-
P1600
(DI-92)ECM BATT MalfunctionOpen in back up power source circuit
ECM
P1780
(DI-94)Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
Park/neutral position switch
ECM

*:-


MIL does not light up



MIL lights up

FI7130
Vehicle Speed
50 - 65 km/h
(31 - 40 mph)
Idling
IG SW OFF
1 - 3 min.
1 min.
Time
(1) (2)
(3)(4)
(5)
- DIAGNOSTICSENGINE
DI-41
1996 TERCEL (RM440U)
DTC P0130 Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
CIRCUIT DESCRIPTION
Refer to DTC P0125 on page DI-38.
DTC No.DTC Detection ConditionTrouble Area
P0130
Voltage output of oxygen sensor remains at 0.4 V or
more, or 0.55 V or less, during idling after the engine is
warmed up (2 trip detection logic)
Oxygen sensor

Fuel trim malfunction
HINT:
Sensor 1 refers to the sensor closer to the engine body.
The oxygen sensor's output voltage and the short-term fuel trim value can be read using the OBD II scan
tool or TOYOTA hand-held tester.
WIRING DIAGRAM
Refer to page DI-38.
CONFIRMATION DRIVING PATTERN
(1) Connect the TOYOTA hand-held tester to the DLC3.
(2) Switch the TOYOTA hand-held tester from normal mode to check mode (See page DI-3).
(3) Start the engine and warm it up with all accessory switches OFF.
(4) Drive the vehicle at 50 - 65 km/h (31 - 40 mph) for 1 - 3 minutes to warm up the oxygen sensor.
(5) Idle the engine for 1 minute.
HINT:
If a malfunction exists, the MIL will light up during step (5).
NOTICE:
If the conditions in this test are not strictly followed, detection of the malfunction will not be possible.
If you do not have a TOYOTA hand-held tester, turn the ignition switch OFF after performing steps
(3) to (5), then perform steps (3) to (5) again.
DI1EB-08

- DIAGNOSTICSENGINE
DI-49
1996 TERCEL (RM440U)
DTC P0171 System too Lean (Fuel Trim)
DTC P0172 System too Rich (Fuel Trim)
CIRCUIT DESCRIPTION
ºFuelº trim refers to the feedback compensation value compared against the basic injection time. Fuel trim
includes short-term fuel trim and long-term fuel trim.
ºShort-term fuel trimº is the short-term fuel compensation used to maintain the air-fuel ratio at its ideal
theoretical value. The signal from the oxygen sensor indicates whether the air-fuel ratio is RICH or LEAN
compared to the ideal theoretical value, triggering a reduction in fuel volume if the air-fuel ratio is rich, and
an increase in fuel volume if it is lean.
ºLong-term fuel trimº is overall fuel compensation carried out long-term to compensate for continual devi-
ation of the short-term fuel trim form the central value due to individual engine differences, wear over time
and changes in the usage environment.
If both the short-term fuel trim and long-term fuel trim are LEAN or RICH beyond a certain value, it is de-
tected as a malfunction and the MIL lights up.
DTC No.DTC Detection ConditionTrouble Area
P0171
When the air-fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the RICH side
(2 trip detection logic)

Air intake (hose loose)

Fuel line pressure

Injector blockage

Heated oxygen sensor malfunction

Manifold absolute pressure sensor

Engine coolant temp. sensor
P0172
When the air-fuel ratio feedback is stable after engine warming
up, the fuel trim is considerably in error on the LEAN side.
(2 trip detection logic)

Fuel line pressure

Injector blockage, leak

Heated oxygen sensor malfunction

Manifold absolute pressure sensor

Engine coolant temp. sensor
HINT:

When DTC P0171 is recorded, the actual air-fuel ratio is on the LEAN side. When DTC P0172 is re-
corded, the actual air-fuel ratio is on the RICH side.

If the total of the short-term fuel trim value and long-term fuel trim value is within + 25 %, the system
is functioning normally.

If the vehicle runs out of fuel, the air-fuel ratio is LEAN and DTC P0171 is recorded. The MIL then
comes on.
DI052-09

DI-52
- DIAGNOSTICSENGINE
1996 TERCEL (RM440U)
DTC P0300 Random/Multiple Cylinder Misfire Detected
DTC P0301 Cylinder 1 Misfire Detected
DTC P0302 Cylinder 2 Misfire Detected
DTC P0303 Cylinder 3 Misfire Detected
DTC P0304 Cylinder 4 Misfire Detected
CIRCUIT DESCRIPTION
Misfire: The ECM uses the crankshaft position sensor and camshaft position sensor to monitor changes in
the crankshaft rotation for each cylinder.
The ECM counts the number of times the engine speed change rate indicates that misfire has occurred. And
when the misfire rate equals or exceeds the count indicating that the engine condition has deteriorated, the
MIL lights up.
If the misfire rate is high enough and the driving conditions will cause catalyst overheating, the MIL blinks
when misfiring occurs.
DTC No.DTC Detection ConditionTrouble Area
P0300Misfiring of random cylinders is detected during any particular
200 or 1,000 revolutions
Ignition system


Injector
P0301
P0302
For any particular 200 revolutions of the engine, misfiring is
detected which can cause catalyst overheating
(This causes MIL to blink)

Injector

Fuel line pressure

Compression pressure

Valve clearance not to specification
P0302
P0303
P0304For any particular 1,000 revolutions of the engine, misfiring is
detected which causes a deterioration in emissions
(2 trip detection logic)
Valve clearance not to s ecification

Valve timing

Manifold absolute pressure sensor

Engine coolant temp. sensor
HINT:
When the 2 or more codes for a misfiring cylinder are recorded repeatedly but no Random Misfire code is
recorded, it indicates that the misfires were detected and recorded at different times.
DI39Y-04

A15705
A15706
- DIAGNOSTICSENGINE
DI-65
1996 TERCEL (RM440U)
DTC P0401 Exhaust Gas Recirculation Flow Insufficient
Detected
CIRCUIT DESCRIPTION
The EGR system recirculates exhaust gas, which is controlled to the proper quantity to suit the driving condi-
tions, into the intake air mixture to slow down combustion, reduce the combustion temp. and reduce NOx
emissions. The amount of EGR is regulated by the EGR vacuum modulator according to the engine load.
If even one of the following conditions is fulfilled, the VSV is
turned OFF by a signal from the ECM.
This results in atmospheric air acting on the EGR valve, closing
the EGR valve and shutting off the exhaust gas (EGR cut-off).

Before the engine is warmed up.

During deceleration (throttle valve closed).

Light engine load (amount of intake air very small).

Engine speed over 4,400 rpm.

Engine racing.
DTC No.DTC Detection ConditionTrouble Area
P0401
After the engine is warmed up, the intake manifold absolute
pressure is larger than the value calculated by the ECM while
the EGR system is ON.
(2 trip detection logic)

EGR valve stuck closed

Open or short in VSV circuit for EGR

Vacuum or EGR hose disconnected

Manifold absolute pressure sensor

EGR VSV open or close malfunction

ECM
WIRING DIAGRAM
DI95P-01