1996 TOYOTA TERCEL clock

N12807
N12808
BE1348
OFFBright
(0 W)
Dark
(10 W)
- BODY ELECTRICALCOMBINATION METER
BE-43
1996 TERCEL (RM440U)
18. INSPECT INTEGRATION RELAY OPERATION
(a) Connect the positive (+) lead from the battery to terminals
3 and 9.
(b) Connect the terminal 2 to terminal 9 through the 3.4 W test
bulb.
(c) Connect the negative (-) lead from the battery to terminal
7.
(d) Check that the bulb lights and the chime sounds for 4 -
8 seconds.
(e) Return to step (a), and operate the chime again.
(f) Connect the negative (-) lead from the battery to terminal
3.
(g) Check that the chime stops sounding.
HINT:
Check the chime within a period of 4 to 8 seconds.
If operation is not as specified, replace the relay.
19. INSPECT INTEGRATION RELAY CIRCUIT
(See page BE-1 1)
20. INSPECT LIGHT CONTROL RHEOSTAT
(a) Turn the rheostat knob OFF, and check that there is no
continuity between terminals.(Rheostat knob turned to
fully counterclockwise.)
(b) Gradually, turn the rheostat knob from the dark side to
bright side, and check that the resistance decreases from
10 to 0 W .(Rheostat knob turned to clockwise.)
If operation is not as specified, replace the rheostat.

Z14869
UP
DOWN
N12812
(a)
(b)
N12813
(a)
(b)
Z06307
Z06308
- BODY ELECTRICALPOWER WINDOW CONTROL SYSTEM
BE-51
1996 TERCEL (RM440U)
Rear Door:
Switch positionTester connectionSpecified condition
UP1 - 2, 3 - 4Continuity
OFF1 - 2, 4 - 5Continuity
DOWN2 - 3, 4 - 5Continuity
If continuity is not as specified, replace the switch.
5. Driver 's Door and Rear RH Side:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
6. Passenger 's Door and Rear LH Side:
INSPECT POWER WINDOW MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative (-) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
7. Driver 's Door:
INSPECT CIRCUIT BREAKER OPERATION
(a) Disconnect the connector from the power window switch.
(b) Connect the positive (+) lead from the battery to terminal
6 and the negative (-) lead to terminal 13 on the wire har-
ness side connector, and raise the window to full closed
position.
(c) Continue to apply voltage, check that there is a circuit
breaker operation noise within approximately 4 to 40 se-
conds.
(d) Reverse the polarity, check that the window begins to de-
scend within approximately 60 seconds.
If operation is not as specified, replace the motor.

BO1IC-04
N15778
No.2 Heater to
Register Duct
Center Heater to
Register Duct
Instrument Panel Reinforcement
AG
AA
G
G
G
G
G
G
A
A Instrument Panel
Brace No.1
Instrument Panel
Brace No.2
Clock Hole Cover
C
CInstrument Panel
Heater
Control
B
B
B
B
DDD
Lower Center Finish Panel
Center Upper
Cluster Finish Panel
Combination
Mater
Steering Column Cover
Front Pillar Garnish
Combination Switch
Cowl Side
Trim
Front Door
Scuff Plate
Instrument Panel
Lower Pad
Lower Center Finish Panel
Steering Wheel
Center Cluster
Finish Panel
Shifting Hole
Bezel
F
F
Ash Receptacle BoxD
D
D
D
Console Box
Lower Instrument Cover
BB
BBHeater Control Panel
Knob
- BODYINSTRUMENT PANEL
BO-45
1139 Author
: Date
:
1996 TERCEL (RM440U)
INSTRUMENT PANEL
COMPONENTS

N12054
N12053
- BODYINSTRUMENT PANEL
BO-49
1996 TERCEL (RM440U)
21. REMOVE NO. 2 HEATER TO REGISTER DUCT
Remove the clip and the duct.
22. REMOVE CLOCK HOLE COVER
Using a screwdriver, remove the clock then disconnect the con-
nector.
HINT:
Tape the screwdriver tip before use.
23. REMOVE INSTRUMENT PANEL
Remove the 4 bolts, nuts and the instrument panel.
24. CENTER HEATER TO REGISTER DUCT
25. INSTRUMENT PANEL BRACE NO. 1
26. INSTRUMENT PANEL BRACE NO. 2
27. INSTRUMENT PANEL REINFORCEMENT