1996 TOYOTA TERCEL sensor

SA12B-02
- SUSPENSION AND AXLEFRONT DRIVE SHAFT
SA-23
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page SA-18).
HINT:
After installation, check ABS speed sensor signal and front wheel alignment (See page DI-1 11 and
SA-4).

SA1W8-02
- SUSPENSION AND AXLEFRONT SHOCK ABSORBER
SA-25
1996 TERCEL (RM440U)
REMOVAL
1. REMOVE FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE FLEXIBLE HOSE
Remove the bolt and disconnect the flexible hose from the shock absorber.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
3. w/ ABS:
DISCONNECT ABS SPEED SENSOR WIRE HARNESS
Remove the bolt and disconnect the ABS speed sensor wire harness from the shock absorber.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. DISCONNECT SHOCK ABSORBER FROM STEERING KNUCKLE
Remove the 2 nuts and bolts and disconnect the shock absorber from steering knuckle,
Torque: 245 N´m (2,500 kgf´cm, 181 ft´lbf)
HINT:
Coat the nut's threads with engine oil.
5. REMOVE SHOCK ABSORBER AND COIL SPRING
(a) Remove the 3/4 nuts on the upper side of the shock absorber.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(b) Remove the shock absorber with the coil spring.

BR0S4-05
R15521
Fender Liner
Front Speed
Sensor
Sensor Rotor
- BRAKEFRONT SPEED SENSOR
BR-41
915 Author
: Date
:
1996 TERCEL (RM440U)
FRONT SPEED SENSOR
COMPONENTS

BR0S5-06
R04569
R04570
BR-42
- BRAKEFRONT SPEED SENSOR
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT SPEED SENSOR CONNECTOR
(a) Remove the fender liner.
(b) Disconnect the speed sensor connector.
2. REMOVE SPEED SENSOR
(a) Remove the 2 clamp bolts and a clip holding the sensor
harness to the body and shock absorber.
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)

(b) Remove the bolt and speed sensor from the steering
knuckle.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)

BR0S6-06
- BRAKEFRONT SPEED SENSOR
BR-43
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-42).
AFTER INSTALLATION, CHECK SPEED SENSOR SIGNAL (See page DI-1 11)

BR0S7-06
R15522
Sensor Rotor
Brake Drum
Outer Bearing
Nut Lock
Grease Cap Claw Washer

Cotter Pin Rear Speed Sensor

Non-reusable part BR-44
- BRAKEREAR SPEED SENSOR
918 Author
: Date
:
1996 TERCEL (RM440U)
REAR SPEED SENSOR
COMPONENTS

BR0S8-06
R04572
R04573
- BRAKEREAR SPEED SENSOR
BR-45
1996 TERCEL (RM440U)
REMOVAL
1. DISCONNECT SPEED SENSOR CONNECTOR
(a) Remove the rear seat cushion.
(b) Disconnect the speed sensor connector, and pull out the
sensor wire harness with the grommet.
(c) Remove the 3 clamp bolts holding the sensor wire har-
ness to the suspension arm.
Torque: 5.0 N´m (51 kgf´cm, 44 in.´lbf)

2. REMOVE SPEED SENSOR
Remove the bolt and speed sensor from the axle beam.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)

BR0S9-03
BR-46
- BRAKEREAR SPEED SENSOR
1996 TERCEL (RM440U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-45).
AFTER INSTALLATION, CHECK SPEED SENSOR SIGNAL (See page DI-1 11)