1996 TOYOTA LAND CRUISER display

DI5Q3−02
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−243
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, the circuit listed for that code in t\
he table below
(Proceed to the page given for that circuit.).
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
Normal
( DI−271 )System normal−OFF
Source voltage dropBattery
 Airbag sensor assemblyON
11
( DI−247 )
Short in squib circuit (to ground)Steering wheel pad (D squib)
 Front passenger airbag assembly (P squib )
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
12
( DI−254 )
Short in squib circuit (to B+)Steering wheel pad (D squib)
 Front passenger airbag assembly (P squib)
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
14
( DI−260 )
Open in D squib circuitSteering wheel pad (D squib)
 Spiral cable
 Airbag sensor assembly
 Wire harness
ON
31
( DI−265 )Airbag sensor assembly malfunctionAirbag sensor assemblyON
54
( DI−267 )Open in P squib circuitFront passenger airbag assembly (P squib)
 Airbag sensor assembly
 Wire harness
ON
HINT:
When the SRS warning light remains lit up and the DTC is the normal code\
, this means a source drop
voltage.
This malfunction is not stored in memory by the airbag sensor assembly a\
nd if the power source volt-
age returns to normal, the SRS warning light will automatically go out.
When 2 or more codes are indicated, the codes will be displayed in numer\
al order starting from the
lowest numbered code.
If a code not listed on the chart is displayed, the airbag sensor assemb\
ly is faulty.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5Q6−01
DI−246
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
Proceed with troubleshooting of each circuit in the table below.
SymptomSuspect AreaSee page
With the ignition switch at ACC or ON, the SRS warning light
sometimes lights up after approx. 6 seconds have elapsed.
 SRS warning light lights up even when ignition switch is in the
LOCK position.
SRS warning light system malfunction
(Always lit up when ignition switch is in LOCK position.)DI−274
With the ignition switch at ACC or ON, the SRS warning lights
does not light up.SRS warning light system malfunction
(Does not light up when ignition switch is turned to ACC or
ON.)
DI−276
DTC not displayed.
 SRS warning light is always lit up with a DTC check procedure.
 DTC displayed without Tc and E1 terminal connection.
Tc terminal circuitDI−279
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R14285 AB0119H00021
Airbag Sensor Assembly
ON
IG2
ACC
(+)
(−)
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−265
1996 LAND CRUISER (RM451U)
DTC 31 Airbag Sensor Assembly Malfunction
CIRCUIT DESCRIPTION
The airbag sensor assembly consists of a airbag sensor, safing sensor, drive circuit, diagnosis circuit and
ignition control, etc.
It receives signals from the airbag sensors, judges whether or not the SRS must be activated, and diagnosis
system malfunction.
DTC 31 is recorded when occurrence of a malfunction in the airbag sensor\
assembly is detected.
DTC No.DTC Detection ConditionTrouble Area
31 Airbag sensor assembly malfunctionAirbag sensor assembly
INSPECTION PROCEDURE
HINT:
When a malfunction code other than code 31 is displayed at the same time, fi\
rst repair the malfunction indi-
cated by the malfunction code other than code 31.
1 Preparation (See step 1 on page DI−271).
2 Check voltage at IG2 and ACC of airbag sensor assembly.
PREPARATION:
Turn ignition switch ON.
CHECK:
Measure voltage between terminals IG2 and ACC of airbag
sensor assembly and body ground.
OK:
Voltage: Below 16 V
NG Check battery and charging system (See page CH−2).
OK
DI5QA−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13678
Airbag Sensor
Assembly
Battery F/B
R/B No.2
2
2
1
1
36 4
6 10
9
S4
GR
B
W
L−R
B−L
B−R ACC
IG2
A
IGN
AM1
AM2
FL BLOCK
W−R
B−L
W−R
Ignition
Switch
B
EA2
EA2
4
11 3
CIG
J3 Junction
Connector
GR 4
33
S5 S5
S4
A
2 2
50A AM1
2
2
Short ConnectorGR
B−W
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−271
1996 LAND CRUISER (RM451U)
DTC Normal Source Voltage Drop
CIRCUIT DESCRIPTION
The SRS is equipped with a voltage −increase circuit (DC−DC converter) in the airbag sensor assembly in
case the source voltage drops.
When the battery voltage drops, the voltage −increase circuit (DC−DC converter) functions to increase the
voltage of the SRS to normal voltage.
The diagnosis system malfunction display for this circuit is different to other circuits −when the SRS warning
light remains lit up and the DTC is a normal code, source voltage drop is ind\
icated.
Malfunction in this circuit is not recorded in the airbag sensor assembly, and the source voltage returns to
normal, the SRS warning light automatically goes off.
DTC No.DTC Detection ConditionTrouble Area
NormalSource voltage dorp Battery
 Airbag sensor assembly
WIRING DIAGRAM
DI5QC−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13679
BatteryFL BLOCK 2
MAIN
W
W
ECU−B
1
F/B
S7
B−R
2
3
SRS Warning
Light
8LA
Tc
B−Y8
IH1 Airbag Sensor
Assembly
DLC1
5 W−L
11
GENERATOR
(ALTERNATOR)
W
Cruise Control ECU
W−L
W−L
B−Y
B−Y
IH1 S7 S6
S6
Short Connector
Short Connector W−L
B−L
11
12
3
EA3 11
22
7
DI−274
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Always lit up, when igni-
tion switch is in LOCK position.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
DI5QD−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N14677
Fuse
DI−276
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Does not light up, when
ignition switch is turned to ACC or ON.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
Refer to page DI−274 for the WIRING DIAGRAM.
INSPECTION PROCEDURE
1 Check ECU−B Fuse.
PREPARATION:
Remove ECU−B fuse.
CHECK:
Check continuity of ECU −B fuse.
OK:
Continuity
HINT:
Fuse may be burnt out even if it appears to be OK during
visual inspection.
If fuse is OK, install it.
NG Go to step 5.
OK
2 Preparation. (See step 1 on page DI−271)
DI5QE−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R13680
Airbag Sensor
AssemblyTc7
B−L
IH1B−Y
11
3
Tc E 1
DLC1 BR−B
EC
S6
S7 11
B−Y
Short Connector 2
2
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−279
1996 LAND CRUISER (RM451U)
Tc Terminal Circuit
CIRCUIT DESCRIPTION
By connecting terminals Tc and E1 of the DLC1 the airbag sensor assembly is set in the DTC output mode.
The DTCs are displayed by the blinking of the SRS warning light.
WIRING DIAGRAM
DI5QF−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AB0117 AB0118 AB0119H00258
LOCKACCON
or
AB0118
R14305 AB0119
H00030
ACCON
or E1Tc
(+)
(−)
DLC1
DI−280
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
If the DTC is not displayed, perform the following troubleshooting.
1 Does SRS warning light light up for approx. 6 seconds?
PREPARATION:
Check operation of SRS warning light after ignition switch is
turned from LOCK position to ACC or ON position.
NO Check SRS warning light system. (See page DI−240 )
YES
2 Check voltage between terminals Tc and E1 of DLC1.
PREPARATION:
Turn ignition switch to ACC or ON.
CHECK:
Measure voltage between terminals Tc and E1 of DLC1.
OK:
Voltage: 10 − 14 V
OK Go to step 4.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010