1996 TOYOTA LAND CRUISER Ignition switch

D00077 BE3840D00092
ON
ON
OFF
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−175
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
O/D OFF indicator light does not light up:
1 Check operation of O/D main switch.
CHECK:
(a) Turn the ignition switch ON.
(b) Check the O/D OFF indicator light when the O/D main
switch is pushed in to ON.
OK:
O/D OFF indicator light goes off
CHECK:
Check the O/D OFF indicator light when the O/D main switch is
pushed again to OFF.
OK:
O/D OFF indicator light lights up
NG Go to step 4.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q08230D00093
ON
OD2
DI−176
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check OVRDRIVE CUT SW2 signal.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Read the OVRDRIVE CUT SW2 signal on the TOYOTA hand −
held tester.
OK:
O/D Main SwitchOVRDRIVE CUT SW2 Signal
O/D ON (pushed in)OFF
O/D OFF (pushed out)ON
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Check the voltage between terminal OD2 of the ECM and body
ground.
OK:
O/D Main SwitchVoltage
O/D ON9 − 14 V
O/D OFFBelow 3 V
OK Proceed to next circuit inspection shown on
problem symptoms table (See page DI−147 ).
NG
3 Check harness and connector between O/D OFF indicator light and ECM (Se\
e page IN−28 ).
NG Repair or replace harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08584
ECM
Pattern Select Switch*
(PWR Mode Switch)
PWR
E7
P−B
B−W
PWR Indicator Light
(Combination Meter)
ID2
63
C12
13
16
20
15
B
J6
EGU−IG
Fuse Block
Ignition Switch
EA2
AM1
IG1
Fuse Block
AM1
P−B
P−B
6 B
B B ID2
B−W
B−W
3
1
B−Y
2
4
222
1 FL AM1
F6
Battery
2
2
3
4
WB −L
R/B No. 2
R/B No. 2
Pattern Select Switch (PWR Mode Switch)
When the PWR mode switch is pushed in, the switch is contacted and
the PWR mode is celected.
To cancel the PWR mode, push the PWR mode switch onec again.
*:
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−179
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (PWR Mode Switch)
CIRCUIT DESCRIPTION
The ECM memory contains the shift programs for the NORMAL and POWER pattern\
s, 2 position, L position
and the lock −up patterns. Following the programs corresponding to the signals from th\
e pattern select
switch, the park/neutral position switch and other various sensors, the ECM swi\
tches the solenoid valves
ON and OFF, and control the transmission gear change and the lock −up clutch operation.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check operation of PWR indicator light.
PREPARATION:
Check if the PWR indicator light normally when the PWR mode switch is set to NORM and PWR position.
NG Check and repair PWR indicator light.
OK
DI5L6−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q08229D00094
PWR
ON
DI−180
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
2 Check PATTERN SEL SW signal.
When using TOYOTA hand −held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect a TOYOTA hand−held tester to the DLC3.
(c) Turn the ignition switch ON and TOYOTA hand−held tes-
ter main switch ON.
CHECK:
Read the PWR signal on the TOYOTA hand −held tester.
OK:
PWR Mode SwitchPATTERN SEL SW Signal
PWRON
NORMOFF
When not using TOYOTA hand −held tester:
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal PWR of the ECM con-
nector and body ground when the PWR mode switch is set to
the PWR (POWER) position and NORM (NORMAL) position.
OK:
PWR Mode SwitchVoltage
PWR7.5 − 14 V
NORMBelow 1.5 V
HINT:
The ECM uses the normal pattern signal if the power signal is
not input.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08580
R−W
J1
A
W 5BRY
IG3
O
Ignition Switch
Fuse Block
GAUGE
Pattern Select Switch*
(2nd Start Switch)
B ECM
18
IH2 12
HI
1
113
9
E4
2C12
Battery
FL AM1
Fuse Block
B−L
W
B−Y
2
4
F6
6 A
A
Y
3
1
E4HOLD
2
EA2
AM1
22
1
AM1 IG1
B
C12
ID3 IH2
O
R−W
2 2
3
42nd STRT Indicator Light
(Combination Meter)
12
Y
R/B No. 2 R/B No. 2
Pattern Select Switch (2nd Start Switch)
When the 2nd start switch is pushed, the switch is contacted and the 2nd\
mode is selected.
To cancel the 2nd start, push the 2nd start swtch once again. The 2nd star\
t is automatically cancelled
out when the ignition switch is turned OFF.
*:
DI−182
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (2nd Start Switch) & 2nd Start
Switch Indicator Light Circuit
CIRCUIT DESCRIPTION
When 2nd start mode is selected with the pattern select switch, the ECM cont\
rols the solenoid valves and
the transmission starts from 2nd gear.
In D position, the transmission automatically shifts up through 3rd to O\
/D as usual.
In 2nd position, the transmission is held in 2nd gear.
WIRING DIAGRAM
DI5L8−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q07359D00023
ON
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−183
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of 2nd start switch.
CHECK:
(a) Turn the ignition switch ON.
(b) Check the ”2nd STRT” indicator light when the 2nd start
switch is pushed in to ON.
OK:
”2nd STRT” indicator light lights up.
CHECK:
Check the ”2nd STRT” indicator light when the 2nd start switch
is pushed again, or PWR mode switch is pushed into OFF.
OK:
”2nd STRT” indicator light goes off. When PWR mode
switch is pushed in to ON, ”2nd STRT” indicator light
goes off, and ”PWR” indicator light lights up.
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
2 Check 2nd start indicator bulb.
NG Replace 2nd start indicator bulb.
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08234
D00096
ONHOLD
HI
DI−184
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
3 Check 2nd start switch.
PREPARATION:
Disconnect the pattern select switch connector.
CHECK:
Check the resistance between terminals 2 and 5 of the pattern
select switch connector when the pattern select switch is set to
2nd start switch ON and OFF.
OK:
2nd Start SwitchResistance
ON0 Ω (continuity)
OFF∞ Ω (open)
NG Replace pattern select switch.
OK
4 Check voltage between terminals HOLD and HI of ECM and body ground.
PREPARATION:
(a) Turn ignition switch ON.
(b) Disconnect the connector from the ECM.
CHECK:
Check the voltage between terminal HOLD of the ECM and
body ground when the select switch is set to 2nd start switch ON
and OFF.
OK:
2nd Start SwitchVoltage
ON9 − 14 V
OFFBelow 1.5 V
CHECK:
Check the voltage between terminal HI of the ECM and body
ground.
OK:
Voltage: 7.5 − 14 V
OK Check and replace ECM.
NG
Check and replace harness and connector between battery and patten select switch, pattern se-
lect switch and ECM, battery and 2nd start indicator light, and 2nd start in\
dicator light and ECM
(See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08580
R-W
J1
A
W 5BRY
IG3
O
Ignition Switch
Fuse Block
GAUGE
(*) Pattern Select Switch
(2nd Start Switch)
B
ECM
18
IH2 12
HI
1
113
9
E4
2
C12
Battery
FL AM1
Fuse Block
B-L
W
B-Y
2
4
F6
6 A
A
Y
3
1
E4HOLD
2
EA2
AM1
22
1
AM1 IG1
B
C12
IG3 IL2
O
R-W
2 2
3
42nd STRT Indicator Light
(Combination Meter)
12
Y
R/B No.2 R/B No.2
DI-185
-
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (2nd Start Switch) & 2nd Start
Switch Indicator Light Circuit
CIRCUIT DESCRIPTION
When 2nd start mode is selected with the pattern select switch, the ECM cont\
rols the solenoid valves and
the transmission starts from 2nd gear.
In D position, the transmission automatically shifts up through 3rd to O\
/D as usual.
In 2nd position, the transmission is held in 2nd gear.
WIRING DIAGRAM
(*) Pattern Select Switch (2nd Start Switch)
When the 2nd start switch is pushed, the switch is contacted and the 2nd\
mode is selected.
To cancel the 2nd start, push the 2nd start switch once again. The 2nd sta\
rt is automatically cancelled out
when the ignition switch is turned OFF.
DI5L8-02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010