1996 TOYOTA COROLLA light

170
Never use a fuse with a higher am-
perage rating, or any other object, in
place of a fuse. This may cause ex-
tensive damage and possibly a fire.CAUTION
!
If any washer does not work, the wash-
er tank may be empty. Add washer
fluid.
You may use plain water as washer fluid.
However, in cold areas where tempera-
tures range below freezing point, use
washer fluid containing antifreeze. This
product is available at your Toyota dealer
and most auto parts stores. Follow the
manufacturer 's directions for how much
to mix with water.
NOTICE
Do not use engine antifreeze or any
other substitute because it may
damage your vehicle's paint.
The following illustrations show how to
gain access to the bulbs. When replacing
a bulb, make sure the ignition switch and
light switch are off. Use bulbs with the
wattage ratings given in the table.
Halogen bulbs have pressurized
gas inside and require special han-
dling. They can burst or shatter if
scratched or dropped. Hold a bulb
only by its plastic or metal case. Do
not touch the glass part of a bulb
with bare hands.CAUTION
!
NOTICE
Only use a bulb of the listed type.
Light BulbsBulb
No.WType
Headlight
(inner bulb)900565A
Headlights
(outer bulb)900655B
Parking and front
side marker lights1943.8D
Front turn signal
lights115627C
Adding washer fluid Replacing light bulbsÐ
ProCarManuals.com

171
Light BulbsBulb
No.WType
Rear turn signal
lights115627C
Stop and tail
lights115727/8C
Rear side marker,
stop and tail
lights
115727/8C
Back-up lights115627C
High mounted
stop light
Sedan
Wagon*
Ð
Ð
115618
21
27D
C
C
License plate
lightsÐ5D
Interior lightÐ8E
Personal lightÐ10C
Luggage
compartment lightÐ5E
Trunk light1943.8D
A: HB3 halogen bulbs
B: HB4 halogen bulbs
C: Single end bulbs
D: Wedge base bulbs
E: Double end bulbs
*: You may use either a 21 W or 27 W bulb.
1. Open the hood.
LEFT SIDE HEADLIGHT: Remove the
clip and take out the air cleaner duct.
ÐHeadlights
ProCarManuals.com

172
2. Unplug the connector while de-
pressing the lock release.
If the connector is tight, wiggle it.3. Turn the bulb and remove it. Install
the new bulb and install the connector.
To install a bulb, align the tabs of the bulb
socket with the cutouts of the mounting
hole.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.Use a Phillips-head screwdriver.
ÐParking and front side
marker lights
ProCarManuals.com

173
Use a Phillips-head screwdriver.
ÐFront turn signal lights
ProCarManuals.com

174
Use a wrench.
Remove and install the cover clips as
shown in the following illustrations.Use a Phillips-head screwdriver.
ÐRear turn signal, stop and
tail, rear side marker, and
back-up lights (sedan)
ProCarManuals.com

175
a: Rear turn signal light
b: Stop and tail light
c: Rear side marker, stop and tail light
d: Back-up lightUse a Phillips-head screwdriver.a: Rear turn signal light
b: Rear side marker, stop and tail light
c: Back-up light
ÐRear turn signal, stop and
tail, rear side marker, and
back-up lights (wagon)
ProCarManuals.com

176
Remove and install the cover clips as
shown in the following illustrations.Remove the bolts.
ÐHigh mounted stoplight
(sedan)
ProCarManuals.com

177
ÐHigh mounted stoplight
(wagon)
ProCarManuals.com