1996 TOYOTA CAMRY buttons

105
5. With your identification number ap-
pearing on the display, press the SCANº
button and hold it in until SECº appears
on the display. SECº will go off to indicate
the system is set. If invalid buttons have
been used, Errº will appear on the display
before SECº appears. Try again from the
step 3.
Once the system is set, the indicator light
turns on and off with the ignition switch in
OFFº and SECº will appear each time
the key is turned to the ACCº position.
To change the identification number for
some reason, cancel the system (See
Cancelling the anti-theft systemº) and
set it again with a new number.The system will be activated if the electri-
cal power source is disconnected from the
radio unit. When the system is activated,
the audio system cannot be turned on
even after the power supply resumes and
SECº will appear on the display. If this
happens, such as when the battery is dis-
charged, see If the anti-theft system is
activatedº.Cancelling the anti-theft system
1. Follow the steps 1 to 4 described in
Setting the anti-theft systemº.
2. With your identification number ap-
pearing on the display, press the SCANº
button and hold it in until - - -º appears
on the display. - - -º will go off to indicate
the system is cancelled. If invalid buttons
have been used, Errº will appear on the
display and SECº appears. Try again
from step 3 in Setting the anti-theft sys-
temº.
ProCarManuals.com

106
The figure with Errº indicates how many
errors you have made. You may make up
to nine errors, but no more!
NOTICE
A tenth error will activate the
anti-theft system and HELPº will
appear on the display. The audio
system will be completely
inoperable. At this time, the
indicator light also comes on. If this
occurs, contact your Toyota dealer.
At the time of resale of your vehicle, can-
cel the system for the new owner.
If the anti-theft system is activated
The audio system made inoperable by the
activated anti-theft system will be oper-
able if you give it the correct identification
number.
1. Follow the steps 3 and 4 described in
Setting the anti-theft systemº.
2. With your identification number ap-
pearing on the display, press the SCANº
button and hold it in until SECº appears
on the display. SECº will go off to indicate
that the system is reset and the audio sys-
tem is operable. If invalid buttons have
been used, Errº will appear on the display
before SECº appears. Try again from the
beginning.See Cancelling the anti-theft systemº for
notes on the figure with Errº.
ProCarManuals.com

11 4(a) Controls and functions
The temperature control knob is used to
adjust the temperature of the delivered
air.
Turn the knob toward the HIGH position
for higher temperature and toward the
LOW position for lower temperature.
The air intake control button is used to se-
lect intake air, either outside air or recircu-
lated air.
With the button in the OUTSIDE AIR
mode, the system will take fresh outside
air into the unit. For recirculated air, set
the button to the RECIRCULATED AIR
mode. Pressing the button once again will
let the button out in the OUTSIDE AIR
mode.
The air flow control buttons are used to
select the air flow outlets air is delivered
from.
See (f) Air flow selectionº for detailed in-
formation.
The fan speed control knob is used to turn
on and off the fan and select the fan
speed.
The higher the fan speed setting is, the
more air is delivered. Turning the knob to
the OFFº position turns off the fan.
The air conditioning on-off button is used
to turn on and off the air conditioning.With the button pressed in, the air condi-
tioning turns on. Pressing the button once
again will turn the air conditioning off.
If the indicator light flashes, contact your
Toyota dealer as soon as possible. There
may be slippage of the drive belt or trouble
in the compressor. If this happens, the air
conditioning is automatically turned off to
avoid damage to the drive belt.
(b) Heating
1. Turn the temperature control knob
anywhere except the LOW position.
When dehumidified heating is desired,
turn the knob between the HIGH and
middle positions.
If cooler air is desired at face level for bi-
level operation, place the knob around the
middle.
2. If quick circulation of heated air is de-
sired, set to the RECIRCULATED AIR
mode of the air intake control button.
For normal use, it is best to set to the
OUTSIDE AIR mode. Otherwise the win-
dows will fog up more easily.
3. Press in the FLOOR button of the air
flow control buttons.
If cooler air is desired at face level for bi-
level operation, press in the BI-LEVEL
button.If the windshield fogs up easily, press in
the FLOOR/WINDSHIELD button.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
If dehumidified heating is desired, press in
the air conditioning on-off button.
(c) Cooling
1. Turn the temperature control knob
anywhere between the middle and LOW
positions.
If warmer air is desired at floor level for bi-
level operation, turn the knob around the
middle.
2. If quick circulation of cooled air is de-
sired, set to the RECIRCULATED AIR
mode of the air intake control button.
For normal use, it is best to set to the
OUTSIDE AIR mode.
3. Press in the FACE button of the air flow
control buttons.
If warmer air is desired at floor level for bi-
level operation, press in the BI-LEVEL
button.ProCarManuals.com

11 5 For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Press in any fan speed control button
except the OFFº button.
5. Press in the air conditioning on-off but-
ton.
(d) Ventilation
1. Turn the temperature control knob at
the LOW position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.
3. Press in the FACE button of the air flow
control buttons.
For detailed information on air flow control
including other settings, see (f) Air flow
selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(e) Windshield defogging and defrost-
ing
To remove interior fog on the windshield:
1. Turn the temperature control knob to
any position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.3. Press in the WINDSHIELD button of
the air flow control buttons.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob any-
where except the OFFº position.
5. Press in the air conditioning on-off but-
ton.
To remove frost or exterior fog on the
windshield:
1. Turn the temperature control knob to
the HIGH position.
2. Set to the OUTSIDE AIR mode of the
air intake control buttons.
3. Press in the WINDSHIELD button of
the air flow control buttons.
For detailed information on air flow con-
trol, see (f) Air flow selectionº.
4. Turn the fan speed control knob to the
HIº position.
5. Leave the air conditioning on-off but-
ton in the OFF position.
(f) Air flow selection
FACE buttonÐThis button directs the air
flow to face level.
BI-LEVEL buttonÐThis button directs
the air flow to face level and the floor. Ex-
cept in ventilation, the air to the floor is
slightly warmer than that to face level.FLOOR buttonÐThis button directs air
flow mostly to the floor.
FLOOR/WINDSHIELD buttonÐThis but-
ton directs air flow to the windshield as well
as the floor.
WINDSHIELD buttonÐThis button di-
rects air flow mostly to the windshield and
front side windows.
Do not use the WINDSHIELD button dur-
ing cooling operation in extremely humid
weather. The difference between the tem-
perature of the outside air and that of the
windshield could cause the outer surface
of the windshield to fog up, blocking your
vision.
(g) Operating tips

Be sure the air inlet grilles in front of the
windshield are not blocked by leaves
or other obstructions.

If air flow control is not satisfactory,
check the dashboard vents. (See
Side ventsº or Lower ventº after
Heater controlsº.)

To help cool down the interior after
parking in the hot sun, drive for the first
few minutes with the windows open.
After the excess heat has blown away,
close the windows.ProCarManuals.com