1996 NISSAN PATHFINDER battery

The front seat(s) are warmed by built-in heat-
ers. The switches located on the instrument
panel can be operated independently of each
other.
1. Start the engine.
The battery could run down if the heater is
operated while the engine is not running.
2. Push the ª
º (Low) or ªº (High)
position of the switch, as desired, depend-
ing on the temperature. The indicator light
in the switch will illuminate.
The heater is controlled by a thermostat,
automatically turning the heater on and off.The indicator light will remain on as long as
the switch is on.
3. When the vehicle's interior is warmed or
before you leave the vehicle, be sure to turn
the switch off.
IDo not use the seat heater for a long
time or when no one is seated there.
IDo not put anything on the seat which
insulates heat, such as a blanket,
cushion, seat cover, etc. Otherwise,
the seat may become overheated.
IDo not place anything hard or heavy
on the seat or pierce it with a pin or
similar object. This may result in
damage to the heater.
IAny liquid spilled on the heating seat
should be immediately wiped up with
a dry cloth.
IWhen cleaning the seat, never use
benzine, thinner, or any similar mate-
rials.
IIf any abnormalities are found or the
heating seat does not operate, turnthe switch OFF and have the system
checked by your NISSAN dealer.
SIC0595
HEATED SEAT (If so equipped)
1-20
Z01.2.1/R50-DX

If the sunroof does not close
Have your NISSAN dealer check and repair
the sunroof.
The interior light has a three-position switch.
The interior light will operate regardless of
ignition key position.
IWhen the switch is in the ªOFFº position,the interior light will not illuminate, regard-
less of door position.
IWhen the switch is in the center ªqº posi-
tion, the light will illuminate when a door is
opened.
IWhen the switch is in the ªONº position, the
interior light will illuminate, whether any
door is open or closed.
Leaving the interior light switch in the
ªONº position for extended periods of
time will result in a discharged battery.
SIC0564
INTERIOR LIGHT
1-29
Z01.2.1/R50-DX

The damping force of the shock absorbers can
be adjusted to the level you desire.
Set the switch to the position you desire ac-
cording to driving conditions.
The sport position is best used for off road
driving. The comfort position is best used for
normal driving.
When the sport position is used, the indicator
on the switch comes on.The Integrated HomeLink
TMTransmitter pro-
vides a convenient way to consolidate the
functions of up to three individual hand-held
transmitters into one built-in device.
THE INTEGRATED HomeLinkTM
TRANSMITTER:
Iwill operate garage doors, gates, home/
office lighting systems and security sys-
tems by storing and transmitting the pro-
gramming information of your current hand-
held transmitters.
Iis built-in and powered by your vehicle's
battery and charging system. No separate
batteries are necessary.
Do not use this Integrated HomeLinkTM
Transmitter with any garage door
opener that lacks safety stop and re-
verse features as required by federal
safety standards (these standards be-
came effective for models manufactured
on April 1, 1982). A garage door opener
which cannot ªdetectº an object in the
path of a closing garage door and then
automatically stop and reverse the door,
does not meet current federal safetystandards. Using a garage door opener
without these features increases the risk
of serious injury or death.
SIC0551
ADJUSTABLE SHOCK
ABSORBER CONTROL (If so
equipped)INTEGRATED HomeLinkTM
TRANSMITTER (If so equipped)
1-31
Z01.2.1/R50-DX

OPERATING THE TRANSMITTER
To operate, simply press the appropriate but-
ton on the Integrated HomeLinkTMTransmit-
ter. The red indicator light illuminates while the
signal is being transmitted. The effective trans-
mission range of the Integrated HomeLink
TM
Transmitter may differ from your hand-held
transmitter.
PROGRAMMING PROBLEM
DIAGNOSIS
Be sure to keep your original hand-held trans-
mitter for possible reprogramming if neces-
sary.
IMake sure batteries in the hand-held trans-
mitter are fully charged.
IHold the hand-held transmitter against the
bottom surface of the Integrated
HomeLink
TMTransmitter so that you can
still see the red indicator light.
IHold buttons for duration of the program-
ming without interruption.
IRotate your hand-held transmitter end-
over-end and program again. For best re-
sults, place the end opposite the battery
compartment against the Integrated
HomeLink
TMTransmitter when program-
ming.
CLEARING THE PROGRAMMING
INFORMATION
To clear the Integrated HomeLinkTMTransmit-
ter of all previous programming information,
simultaneously hold down the outside two but-
tons (#1 & #3) until the red indicator light
begins to flash rapidly (approximately 20 sec-
onds). This will clear all three buttons. Indi-
vidual buttons cannot be cleared, but can be
reprogrammed at any time by following the
programming procedures described above.
IF YOUR VEHICLE IS EVER
STOLEN
If your vehicle has been stolen, you should
change the codes of any device that was
programmed into the Integrated HomeLink
TM
Transmitter as soon as possible. Consult the
owners manual of each device, or call the
manufacturer or dealer of those devices.
When your vehicle is recovered, you will
have to reprogram the Integrated
HomeLink
TMTransmitter with your new
transmitter information.
FCC Notice:
This device complies with FCC rules part
15. Operation is subject to the following
two conditions: (1) This device may notcause harmful interference and (2) this de-
vice must accept any interference that may
be received, including interference that
may cause undesired operation.
The transmitter has been tested and com-
plies with FCC and DOC/MDC rules.
Changes or modifications not expressly
approved by the party responsible for com-
pliance could void the user's authority to
operate the device.
DOC: ISTC 1763K1313
FCC I.D.: CB2V67690
1-33
Z01.2.1/R50-DX

2 Pre-driving checks and adjustments
Key ......................................................................... 2-2
Door locks .............................................................. 2-2
Multi-remote control system (If so equipped) ......... 2-4
Battery replacement ................................................ 2-6
Spare tire carrier .................................................... 2-7
Back door locks ....................................................... 2-8
Rear window locks .................................................. 2-8
Hood release .......................................................... 2-9
Glove box lock ..................................................... 2-10
Fuel filler lid lock .................................................. 2-10
Fuel filler cap ....................................................... 2-11
Front seats ........................................................... 2-12
Rear seats ............................................................ 2-15
Supplemental restraint system
(Supplemental air bag system) ............................ 2-18Warning labels ...................................................... 2-22
Supplemental air bag warning light ..................... 2-22
Seat belts ............................................................. 2-24
Child restraints for infants and
small children ....................................................... 2-30
Tilting steering wheel ........................................... 2-36
Sun visor ............................................................... 2-37
Outside mirror control .......................................... 2-37
Outside mirrors .................................................... 2-38
Inside mirror ......................................................... 2-38
Luggage net .......................................................... 2-39
Luggage side finisher hook ................................... 2-39
Luggage hooks........................................................ 2-40
Luggage rack ........................................................ 2-41
Z01.2.1/R50-DX

Unlocking doors
1. Push the ªº button on the multi-
remote controller.
2. Only the driver side door will unlock. Push
the ª
º button on the multi-remote con-troller again within 5 seconds.
3. All doors will unlock.
4. The interior light will stay on for 30 seconds
when the interior light switch is in the center
ªqº position.The interior light can be turned off without
waiting for 30 seconds by inserting the key into
the ignition or by locking the doors with the
multi-remote controller or by pushing the inte-
rior light button.
Using the panic alarm
If you are near your vehicle and feel threat-
ened, you may activate the alarm to call atten-
tion as follows:
1. Push the ª
º button on the remote
controller forlonger than 1.5 seconds.
2. The theft warning alarm and headlights will
stay on for 30 seconds.
3. The alarm will stop when any of the key
functions are used. For example, when the
ª
º or the ªº button is pushed, or the
ª
º button is pushed for longer than
1.5 seconds on the multi-remote controller,
the panic alarm function will be cancelled.
The remote controller will not function.
IWhen the key is inserted into the key
switch.
IWhen the battery in the remote control-
ler is dead.
IThe distance between the remote con-
SPA0398
2-5
Z01.2.1/R50-DX

troller and vehicle is more than approx.
49 ft (15 m).
IWhen one of the doors is ajar, only the
unlock function can be operated.
Replace the two batteries as follows:
1. Remove the screw and open the lid.
2. Replace the batteries with new ones. Insert
the batteries as illustrated above.
Recommended batteries: Sanyo CR2016
or equivalent.
3. Close the lid securely and install the screw.
4. Press the ª
º button, then the ªº
button two or three times to check the
multi-remote controller operation.
If the batteries are removed for any reasonother than replacement, perform step 4
above.
IAn improperly disposed battery can hurt
the environment. Always confirm local
regulations for battery disposal.
IThe multi-remote controller is water-
proof; however, if it does get wet, imme-
diately wipe completely dry.
IWhen changing batteries, do not let dust
or oil get on the controller.
SPA0399
BATTERY REPLACEMENT
2-6
Z01.2.1/R50-DX

Seat lifter (Driver's seat)
Turn either dial to adjust the angle and height
of the seat cushion to the desired position.
POWER SUPPORT SEAT
IDo not adjust the driver's seat while
driving.
IThe seatback should not be reclined
any more than needed for comfort.
Seat belts are most effective when
the passenger sits well back and
straight up in the seat. If the seat is
reclined, the risk of sliding under the
lap belt and being injured is
increased.
IDo not leave children unattended in-
side the vehicle. They may inadvert-
ently activate switches.
Operating tips
IThe motor has an auto-reset overload pro-
tection circuit. If the motor stops during
operation, wait 30 seconds, then reactivate
the switch.
IDo not operate the power support seat
for a long period of time when the engine is
off. This will discharge the battery.
SPA0099SPA0098
2-13
Z01.2.1/R50-DX