1996 MITSUBISHI 3000GT check engine

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - MFI Circuit167 ~
Check engine/malfunction
Lki @ %\\ Y7FUO999 1
\l-T-T-. .
Engine control
moduleW
16FO297
Xl 6FO498
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - MFI Circuit
,’
L
c
Injector
-I\/-, Y7FUO803
\ R\/1/I‘ relay- 1
I’ I\,?-==,>\ I
1Check engine/malfunction
U68FOOll
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 184CIRCUIT DIAGRAMS - Cooling Circuit

TROUBLESHOOTING HINTS1. Neither the radiator fan nor condenser
fan rotate at all.l Check fusible link No. 5
2. Only the condenser fan does not
operate.l Check dedicated fuse No. 8.
3. The radiator fan and condenser fan do
not operate in the low speed mode, but
operate otherwise.(1) The
AK compressor magnet clutch does
not enter the “ON” state.
lCheck whether the output of the auto
compressor control unit is available.
NOTE
For troubleshooting of the air conditioningcontrol unit, refer to GROUP 55.
(2) The A/C compressor magnet clutch enters
the “ON” state.l Check the resistor.
lCheck the radiator fan motor relay (LO)
and condenser fan motor relay (LO).l
Check the therm0 sensor (for radiator
fan).
(3) The radiator fan does not rotate when the
air conditioning switch is turned ON.l Check the radiator fan motor control
relay.4. The radiator fan and condenser fan do
not operate in the high speed mode, but
operate otherwise.l Check the
therm0 sensor (for condenser
fan).l
Check the radiator fan motor relay (HI) and
condenser fan motor relay (HI).Fan Operating Mode
ant temperature
switch (for air
conditioning
cut-Radiator fan mo-
3°C(239 f 5°F) orover, ON at 108°C
OFFONLOW
LOW
ON
ONHIGHHIGH
ON
OFFHIGH
LOW
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Cooling Circuit185

OPERATIONThe engine control module controls the power
transistors (high speed and low speed) in the moduleto provide radiator fan motor and condenser fan
motor rotation controls in accordance with the engine
coolant temperature and vehicle speed.
NOTEIn the event of faulty water temperature sensor,
the engine control module commands the fan motors
(for both radiator and condenser) to rotate at high
speeds.1. Radiator Fan (Low Speed Rotation)
l
When the engine control module turns onthe power transistor (low speed) in the
module, the current flows from the ignition
switch to the engine control module throughthe radiator fan motor relay (LO) coil.
If the current flows to the fan motor relay
coil, the switch of the relay turns on to supplythe motor driving power (for low speed
rotation). This will cause the current to flow
from the battery to the ground through the
radiator fan motor, relay switch and resistor,rotating the radiator fan at low speeds.
2. Condenser Fan (Low Speed Rotation)
l
The power from the NC compressor lock
controller turns on the condenser fan motorrelay (LO) to rotate the condenser fan at
low speeds.3. Radiator Fan, Condenser Fan (High
Speed Rotation)l
When the engine control module turns onthe power transistor (high speed) in the
module. the radiator fan motor relay (HI)
and condenser fan motor relay (HI) will
operate and the motor driving power (for
high speed rotation) is sent to the radiator
fan motor and condenser fan motor to rotate
the radiator fan and condenser fan at high
speeds.
TROUBLESHOOTING HINTS1. Neither the radiator fan nor condenser
fan rotate at all.
l Check fusible link No. 5.
2. Only the condenser fan does not
operate.l Check dedicated fuse No. 8.
3. The condenser fan do not operate in the
low speed mode, but operate otherwise.
(1) The A/C compressor magnet clutch does
not enter the “ON” state.l Check whether the output of the air
conditioning compressor lock controller
unit is available.
(2) The A/C compressor magnet clutch enters
the “ON” state.l
Check the condenser fan motor relay
(LO)-4. The radiator fan and condenser fan do
not operate in the high speed mode, but
operate otherwise.l Check the engine control unit.
Fan Operating Mode
VehicleA/C compressor lockspeedcontroller output
k%
80 or less[50 or less]
LO
(OV)
80 or more[50 or more]HI (12V)
,_ -
Engine coolanttemperature
$1
Approx. 95 [203] or less
Approx. 95
[203] or more
Approx. 105
[221] or more
Approx. 105
[221] or less
Approx. 105
[221] or more
Approx. 105
[221] or less
Approx. 105
12211 or moreTransistor
Transistor
in enginein engineRadiatorCondensercontrol unitcontrol unitfanfan
Low speedHigh speed
OFF
OFFOFFOFF
ONOFFLow speedOFF
ON
ONHigh speedHigh speed
OFF
OFFOFFOFF
ONONHigh speedHigh speed
ON
OFFLow speedLow speed
ON
ONHigh speedHigh speed
1 TSB Revision1

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Buzzer Circuit211
OPERATION
L
lBattery positive voltage is continuously applied to the key-reminder switch.l
If the driver’s door is opened (door switch ON) with the key inserted in the ignition switch (key-reminderswitch ON), the buzzer sounds to warn that the key has been left in the switch.
&eat belt warning>
lWhen the ignition switch is turned on, the timer circuit and pulse circuit will flicker the seat belt warning
light for approx. 6 seconds with the buzzer intermittently sounding.
lIf the seat belt is fastened for the while, the seat belt switch will be turned off and the buzzer will
stop.
TROUBLESHOOTING HINTS
/
L
ProblemCheck methodThe key-reminder The seat belt warning function l
Check the door switch.
warningdoesn’t is OK.(Refer to GROUP 42-Door Assembly.)
sound.The seat belt warning also l Check the buzzer.
doesn’t function.(Refer to GROUP 52A-Seat Belt.)
The seat belt warn-The seat belt warning light lCheck the seat belt switch.
ing doesn’t
func- flashes.(Refer to GROUP 52A-Seat Belt.)
tion.The seat belt warning light l Check the key-reminder switch.
also does not function (and(Refer to GROUP M-Ignition Switch.)
the key-reminder warning
also does not function).
The buzzer doesn’t stop even through the driver’slCheck the seat belt switch.
seat belt has been buckled.(Refer to GROUP 52A-Seat Belt.)
The seat belt warning light doesn’t flashes (but thelCheck the light bulb.
buzzer sounds).lCheck the key-reminder switch.(Refer to GROUP 54-Ignition Switch.)
lCheck the seat belt switch.
(Refer to GROUP
52A-Seat Belt.)
The warning light does not flash and the warninglCheck the ignition switch input signal.buzzer also does not sound.(Refer to GROUP 52A-Troubleshooting.)l Check the key-reminder switch.
(Refer to GROUP 54-Ignition Switch.)
lCheck the seat belt switch.
(Refer to GROUP 52A-Seat Belt.)
The warning light flashes, but the warning buzzer l
Check the key-reminder switch.
does not sound.(Refer to GROUP M-Ignition Switch.)lCheck the seat belt switch.
(Refer to GROUP 52A-Seat Belt.)
[ TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Power Window Circuit221OPERATION
lTurn on the ignition switch, and the transistor Tr will be turned on by the timer circuit. This will turn
on the power window relay allowing the power window to be opened and closed.
lTurn the ignition switch from on to off, and the timer circuit will be activated to keep transistor Tr
on for 30 seconds allowing the power window to be opened and closed.
Moreover, if the front door is opened, the timer circuit will stop to turn off the transistor Tr. This
will prevent the window from being opened and closed.
TROUBLESHOOTING HINTS
’
PhenomenonInspection method
All door windows cannot be opened or closed.
eCheck fusible link No. 9.
0 Check the power-window relay.
lCheck the power-window main switch.
One of the door windowsNeither of the power- l
Check the power-window main switch.cannot be opened or
window switches (main l
closed.
Check the power-window motor for the power window that
or sub) operatesdoes not operate.Either the power-win- lCheck the power-window switch for the power window
dow main switch or subthat does not operate.
switch does not oper-ate.
The one-touch down switch function only does notlReplace the power-window main switch.
operate.
The power windows do not operate when the ignition
lCheck the ignition switch input signal. (Refer to GROUP
switch is at the “ON” position.
42-Troubleshooting.)
0Check the ignition switch. (Refer to GROUP 54-Ignition
Switch.)
lCheckthepowerwindow relay. (RefertoGROUP42-Power
Window)The power windows can be opened and closed l
Check the front door switch input signal. (Refer to GROUP
immediately after ignition switch is switched “OFF”,42-Troubleshooting.)
but the power window operation does not stop if al
front door is opened within 30 seconds.
Check the front door switch. (Refer to GROUP 42-DoorAssembly.)
The opening and closing operations of the power l
Check the power window relay. (Refer to GROUP 42-Power
windows are possible after the timer operation timeWindow.)
has elapsed when the ignition switch is set to the
“OFF” position.
/
i
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CIRCUIT DIAGRAMS - Central Door Locking Circuit237
OPERATION/
Li!l
When the door lock switch is set to the LOCKside (or UNLOCK side), the LOCK side (or
UNLOCK side) of the door lock relay is turned
ON and the door actuators of all doors operate.l
If the driver seat side door (or assistant seat
side door) is opened and the driver seat side
inside lock knob (or assistant seat side inside

0
,’
id
0
With the driver’s and front passenger’s doorsunlocked, press the LOCK switch of the
transmitter, and the door lock signal output (0V) will be sent from the
keyless entry control
unit terminal No. 12 closing the door lock powerrelays 1 and 2 to lock the driver’s and front
passenger’s doors.
While the R.H. and L.H. doors are in the lockedstate, press the UNLOCK switch of the
transmitter once, and the DOOR UNLOCK
switch signal (0 V) will be sent from the keylessentry control unit terminal No. 14 closing the
door lock power relay 2 to unlock the driver’s
door.
Under the above-mentioned conditions, further
press the UNLOCK switch of the transmitter,and the DOOR UNLOCK signal output (0 V)
will be sent from the keyless entry control unitterminal No. 13 closing the door lock power
relay 1 to lock the front passenger’s door.
When the keyless entry system is operated toturn the driver’s door lock switch from the
UNLOCK position to the LOCK position, thelock knob) is locked with the key inserted in
the ignition switch, the ETACS unit grounds the
unlock side circuit of the door lock relay to unlock
all doors. This way, failure to remove the key
is prevented.dome light/foot light blinking signal output
(system voltage) will be sent twice from the
keyless entry control unit terminal No. 11 when
the door lock switch is turned from the LOCK
position to the UNLOCK position, the lighting
signal output (0 V) will be provided for approx.
3 seconds.
NOTE
The dome light winks or comes on when the domelight switch is in the DOOR interlock position.
However, the dome light does not wink while it .is
ON for 6 seconds after closing the door by ETACS
function.Besides the above-mentioned operations, the
keyless entry control unit has the following functions.l
If any door is not opened or closed within 30
seconds from unlocking the door by means ofthe
keyless entry system, the door is
automatically locked.In addition, if the
cryptographic code other than the code storedin the receiver memory is received 30 times
in one minute continuously, operation of the
unit is suspended for 10 minutes.l
Operation is also suspended if the ignition key
remains inserted (key reminder switch: OFF)
and either door is left open (door switch: ON).TROUBLESHOOTING HINTS

Phenomenon
Inspection method
One of the door lock actuators fails to operate.
0Check the door actuator which fails to operate.
No unlock operation can be made by pressing door lock0
knob after fulfilment of following conditions.Check the key reminder switch input signal.0Check the key reminder switch. (Refer to GROUP
0Insertion of key in ignition switch (key reminder switch54-Ignition Switch.)
OFF)0
0Opening of door (door switch ON)Check the front door switch input signal.0 Check the front door switch. (Refer to GROUP
42-Door Assembly)
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 238CIRCUIT .DIAGRAMS - Central Door Locking Circuit
l
The indicator does not blink after pressing thetransmission switch of the transmitter.
1) Check or replace the battery. (Refer to
GROUP
42-Keyless Entry System.)
2) Replace the transmitter.
l Transmitted wave is being sent from thel
R.H. and L.H. doors can be locked and unlocked
by the transmitter but the dome light and footlight do not blink or come on. (Interlocked
lighting of the dome light and foot light by means
of the dome light switch or door opening and
closing is normal).
transmitter (indicator is blinking), but the system
does not operate.1) Check the cryptographic code registering
method. (Refer to GROUP
42-Keyless
Entry System.)
2)Check the keyless entry control unit terminalvoltage. (Refer to GROUP
42-Trouble-
shooting.)3) Check the coaxial cable of antenna and
the ground wire for connection.
l Only R.H. or L.H. door can be locked or
unlocked.
1)Check the door lock power relay 1 (for front
passenger’s door) or door lock power relay2 (for driver’s door). (Refer to GROUP
42-Central Door Locking System.)
2)Check the keyless entry control unit terminalvoltage. (Refer to GROUP
42-Trouble-
shooting.)
1)Check the keyless entry control unit terminal
voltage (Refer to GROUP
42-Troubleshoot-
ing.)2) Check the harness.
NOTE
l :Perform this check when replacement of the
transmitter and/or
keyless entry control unit or
faulty storage of cryptographic code has been
made.
\
Ilj
‘d I
1 TSB Revision