1996 Mercury Sable coolant temperature

67
*
[ST10325(ALL)04/95]
RWARNING
If the engine idle speed does not
slow down automatically, do not
allow your vehicle to idle for more
than 10 minutes. Have the vehicle
checked. Extended idling at high
engine speeds can produce very high
temperatures in the engine and
exhaust system, creating the risk of
fire or other damage to the vehicle
and may possibly result in personal
injury.
*
[ST10350(ALL)04/95]
RWARNING
Do not park, idle, or operate your
vehicle in tall, dry grass, or other dry
ground areas. The high heat
generated by engine and emissions
components could start a ground fire.
*
[ST10500(ALL)03/95]
If you consistently start your vehicle in subzero
temperatures, use an engine block heater (if
your vehicle has this option).
%*
[ST10600(ALL)03/95]
Engine Block Heater (If equipped)
(Standard in Canada)
*
[ST10700(ALL)03/95]
Engine block heaters are strongly recommended
if you live in a region where temperatures reach
-10ÊF (-23ÊC) orbelow. An engine block heater
warms the engine coolant, which improves
starting, warms up the engine faster, and allows
the heater-defrost system to respond quickly.
*
[ST10900(ALL)01/95]
To turn the heater on, simply plug it into a
grounded 110-volt outlet. Ford recommends that
you use a 110-volt circuit that is protected by a
ground fault circuit interrupter.
File:fcsts.ex
Update:Wed Dec 20 09:34:24 1995

99 [IP06025(ALL)03/95]
When in AUTO and weather conditions require
heat, air will be sent to the floor. But a feature is
included in your EATC to prevent blowing cold
air to the floor if the engine coolant is not warm
enough to allow heating. The EATC will direct
the airflow to the windshield at low fan speed.
In 3-1/2 minutes or less, the fan speed will start
to increase and the airflow will change to the
floor area.
[IP06100(ALL)03/95]
When in AUTO and weather conditions require
cooling, the EATC will use outside air or
recirculated air, depending on the temperature
that is selected.
[IP06125(ALL)04/95]
If unusual conditions exist (i.e., window fogging,
etc.), the six manual override buttons allow you
to select special air discharge locations. The fan
speed button allows you to adjust the fan speed
to suit your needs.
*
[IP06225(ALL)03/95]
Temperature selection
[IP06325(ALL)04/95]
The TEMP button at the upper left of the
Control is for temperature selection. The
aside
of the TEMP button will increase the set
temperature and the
bside of the TEMP button
will lower the set temperature. Pressing the
button and releasing it will change the set
temperature one degree. Holding either side of
the button in will rapidly change the
temperature setting in one degree increments to
either65ÊF (18ÊC) or 85ÊF (29ÊC).Then, the set
temperature will jump 5ÊF(3ÊC) andstop at
either60ÊF (16ÊC)which is maximum cooling or
90ÊF (32ÊC)which is maximum heating.
[IP06525(ALL)02/95]
The average temperature range used is between
68ÊF (20ÊC) and 78ÊF (26ÊC).Changing the
temperature setting by several degrees outside
this range or overriding to 60Ê or90ÊF (16Ê or
32ÊC) asdescribed above will not speed up the
heating or cooling process.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

84
*
[LG08396(ALL)10/93]
Gauges
%*
[LG08400(ALL)01/95]
Fuel Gauge
[LG08425(ALL)11/94]
The fuel gauge displays approximately how
much fuel is in the fuel tank only when the
ignition is in the ON position.
[LG08525(ALL)11/94]
For proper fuel gauge indication after adding
fuel, the ignition should be in the OFF position
while the vehicle is being refueled.
*
[LG08625(ALL)06/93]
The fuel gauge indicator may vary slightly when
the vehicle is in motion.
[LG08725(ALL)11/94]
With the ignition in the OFF position, the fuel
gauge indicator may drift from the ignition ON
indication.
%*
[LG08800(ALL)01/95]
Engine Coolant Temperature Gauge
*
[LG08900(ALL)03/95]
This gauge indicates the temperature of the
engine coolant, not the coolant level. If the
coolant is not at its proper level or mixture, the
gauge indication will not be accurate.
*
[LG09000(ALL)02/95]
The pointer moves from the C (cold) mark into
the Normal band as the engine coolant warms
up. It is acceptable for the pointer to fluctuate
within the Normal band under normal driving
conditions. Under certain driving conditions,
such as heavy stop and go traffic or driving up
hills in hot weather, the pointer may indicate at
the top of the Normal band.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

85 [LG09005(ALL)02/95]
one third page art:0001095-B
Engine coolant temperature gauge
*
[LG09100(ALL)02/95]
If, under any circumstances, the pointer moves
above the Normal band, the engine coolant is
overheating and continued operation may cause
engine damage.
*
[LG09150(ALL)01/95]
If your engine coolant overheats:
*
[LG09200(ALL)03/95]
1. Pull off the road as soon as safely possible.
*
[LG09300(ALL)01/95]
2. Turn off the engine.
*
[LG09400(ALL)11/94]
3. Let the engine cool.
*
[LG09410(ALL)04/95]
4. Check the coolant level following the
instructions on checking and adding coolant
to your engine, seeEngine Coolantin the
Index. If you do not follow these
instructions, you or others could be injured.
[LG09415(ALL)11/94]
If the coolant continues to overheat, have the
cooling system serviced.
%*
[LG09800(ALL)01/95]
Speedometer
*
[LG09900(ALL)01/95]
The speedometer tells you how many miles
(kilometers) per hour your vehicle is moving.
%*
[LG10000(ALL)01/95]
Odometer
*
[LG10100(ALL)01/95]
The odometer tells you the total number of miles
(kilometers) your vehicle has been driven.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

99 [IP06025(ALL)03/95]
When in AUTO and weather conditions require
heat, air will be sent to the floor. But a feature is
included in your EATC to prevent blowing cold
air to the floor if the engine coolant is not warm
enough to allow heating. The EATC will direct
the airflow to the windshield at low fan speed.
In 3-1/2 minutes or less, the fan speed will start
to increase and the airflow will change to the
floor area.
[IP06100(ALL)03/95]
When in AUTO and weather conditions require
cooling, the EATC will use outside air or
recirculated air, depending on the temperature
that is selected.
[IP06125(ALL)04/95]
If unusual conditions exist (i.e., window fogging,
etc.), the six manual override buttons allow you
to select special air discharge locations. The fan
speed button allows you to adjust the fan speed
to suit your needs.
*
[IP06225(ALL)03/95]
Temperature selection
[IP06325(ALL)04/95]
The TEMP button at the upper left of the
Control is for temperature selection. The
aside
of the TEMP button will increase the set
temperature and the
bside of the TEMP button
will lower the set temperature. Pressing the
button and releasing it will change the set
temperature one degree. Holding either side of
the button in will rapidly change the
temperature setting in one degree increments to
either65ÊF (18ÊC) or 85ÊF (29ÊC).Then, the set
temperature will jump 5ÊF(3ÊC) andstop at
either60ÊF (16ÊC)which is maximum cooling or
90ÊF (32ÊC)which is maximum heating.
[IP06525(ALL)02/95]
The average temperature range used is between
68ÊF (20ÊC) and 78ÊF (26ÊC).Changing the
temperature setting by several degrees outside
this range or overriding to 60Ê or90ÊF (16Ê or
32ÊC) asdescribed above will not speed up the
heating or cooling process.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

282
*
[SV19850(ALL)03/95]
q
Check for leaks at the draincock.
*
[SV19900(ALL)03/95]
q
Recheck the engine coolant level, using the
recommended procedure, after one or two
occasions of vehicle use.
[SV19950(ALL)04/95]
About Your Battery
*
[SV20001(ALL)02/95]
Your vehicle may have a Motorcraft
maintenance-free battery. When the original
equipment battery is replaced under warranty, it
may be replaced by a Motorcraft
Low-Maintenance Battery.
[SV20850(ALL)04/95]
Because your vehicle's engine is electronically
controlled by a computer, some control
conditions are maintained by power from the
battery. If you ever disconnect the battery or
install a new battery, you must allow the
computer to ªrelearnº its idle conditions before
your vehicle will drive properly. To begin this
process, put the gearshift in P (Park), set the
parking brake, turn off all the accessories, and
start the vehicle. Bring the engine to normal
operating temperature. Allow the engine to idle
for one minute in N (Neutral) and one minute in
Drive or Overdrive. Perform the previous
procedure with the air conditioning on and off
(conditions permitting). The relearning process
will complete automatically as you drive the
vehicle.
*
[SV21000(ALL)03/95]
If you do not let the engine relearn its idle, the
idle quality of your vehicle may be adversely
affected until the idle is relearned. Your vehicle
will eventually relearn its idle while you drive
it, but it takes much longer than if you use the
previous procedure.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

284
*
[SV22400(ALL)01/95]
RWARNING
Do not add the windshield washer
fluid to the engine coolant reservoir.
This could damage your cooling
system. Do not add engine coolant to
the washer fluid reservoir. This could
damage your wiper/washer system.
*
[SV22500(ALL)01/95]
Use specially formulated windshield washer
fluid rather than plain water, because specially
formulated washer fluids contain additives that
dissolve road grime. For safety reasons, washer
fluids containing an appropriate antifreeze such
as methanol should be used in freezing weather
(temperatures below32ÊF [0ÊC]).State or local
regulations on Volatile Organic Compounds
(VOC's) may restrict use of the most common
antifreeze, methanol. Washer fluids containing
non-methanol antifreeze agents should be used
only if they provide cold weather protection
without damaging the vehicle's paint finish,
wiper blades, and windshield washer system.
[SV22550(ALL)04/95]
RWARNING
Washer solution contains methanol
which is poisonous. Observe all
warnings indicated on label of
washer solution.
[SV22600(ALL)06/94]
Checking the washer fluid for the
liftgate (If equipped)
[SV23100(ALL)04/95]
If your wagon has a rear window wiper, check
the reservoir for its washer fluid regularly. This
is not the same reservoir that your windshield
wipers use. The opening for this reservoir is on
the right side of the liftgate opening, below the
tail lamp. Refill this reservoir with the same
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

301
%*
[SV31200(ALL)03/95]
Power Steering Fluid
*
[SV31300(ALL)01/95]
Check the level of the power steering fluid at
least twice a year (i.e., every Spring and Fall).
%*
[SV31400(ALL)03/95]
Checking and Adding Power Steering
Fluid
*
[SV31500(ALL)02/95]
1. Start the engine and let it run until the
power steering fluid reaches normal
operating temperature. The power steering
fluid will be at the right temperature when
the engine coolant temperature gauge in the
instrument cluster is near the center of the
NORMAL operating temperature range.
*
[SV31600(ALL)01/95]
2. While the engine idles, turn the steering
wheel back and forth several times. Make
sure that the cap assembly is installed at this
time.
*
[SV31700(ALL)01/95]
3. Then turn the engine off.
[SV31800(ALL)04/95]
3.0L Vulcan engine:
%*
[SV31900(ALL)03/94]
4. Check the fluid level on the dipstick (which
is highlighted in yellow in your vehicle). The
fluid level should be between the arrows in
the FULL HOT range, which is marked on
the side of the dipstick, opposite the side
marked FULL COLD. Do not add fluid if the
level is within the FULL HOT range.
*
[SV32100(ALL)07/94]
5. If the power steering fluid is low, add fluid
in small amounts, continuously checking the
level, until you reach the FULL HOT range.
Do not overfill.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995