1996 Mercury Sable bulb

89 [LG15800(ALL)04/95]
Low Fuel Light (If equipped)
[LG15900(ALL)03/95]
This light comes on when your fuel gauge
indicates approximately 1/16 of a tank. The
ignition must be turned to the ON position for
this light to come on. This light will glow
steadily.
[LG16000(ALL)04/95]
one inch art:0000116-C
Low fuel light
[LG16100(ALL)02/95]
Rear Lamp Out Indicator (If equipped)
[LG16200(ALL)02/95]
This light indicates that a rear tail lamp or
brakelamp is not functioning. It comes on
momentarily when the ignition is turned to the
START position, then goes out.
[LG16220(ALL)02/95]
This light will come on to show a rear tail lamp
burnout when the light switch is turned to the
parking lamp or headlamp position.
[LG16260(ALL)04/95]
This light will come on to show a brakelamp
burnout only when the brake pedal is pressed.
[LG16280(ALL)02/95]
The light will stay on until the ignition is turned
to the OFF position.
[LG16300(ALL)02/95]
one inch art:0000117-B
Rear lamp out light
[LG16400(ALL)12/91]
NOTE: The warning light may not work or
you may get a false reading if you use
trailer lights or use improper
replacement bulbs.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

255
Servicing Your Sable
%*
[SV00300(ALL)03/95]
Service Made Easy
*
[SV00400(ALL)01/95]
Ford has two goals for servicing your vehicle.
*
[SV00500(ALL)01/95]
1. When we can, we design parts that do not
need to be serviced.
*
[SV00600(ALL)01/95]
2. We want to make servicing your vehicle as
easy as possible. To help you:
*
[SV00700(ALL)01/95]
q
We highlight do-it-yourself items in yellow in
the engine compartment so that you can find
them easily.
*
[SV00800(ALL)01/95]
q
When possible, we design parts Ð such as
the headlamp bulbs Ð that can be replaced
without tools.
*
[SV00900(ALL)05/94]
q
We give you a Maintenance Schedule that
makes tracking routine service for your
vehicle easy. The maintenance schedule is
located in theMaintenance Schedule and Record
booklet.
*
[SV01000(ALL)01/95]
This chapter tells you about the basic parts that
you need to check and service regularly.
*
[SV01100(ALL)03/95]
If your vehicle needs professional servicing, see
theCustomer Assistancechapter.
*
[SV01200(ALL)03/95]
Check yourWarranty Information Bookletto find
out which parts are covered.
*
[SV01250(ALL)03/95]
Ford Motor Company recommends that you
perform the Owner Maintenance Checks listed in
theMaintenance Schedule and Recordbooklet.
These services are important for the proper
operation of your vehicle. In addition to the
conditions listed in the Owner Maintenance
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

315 %
*
[SV38800(ALL)03/95]
Replacing the Headlamp Bulb
*
[SV38900(ALL)01/95]
The headlamps on your vehicle use replaceable
bulbs. When the lamp burns out, simply replace
the bulb, rather than the whole lamp.
*
[SV39000(ALL)01/95]
RWARNING
Handle a halogen headlamp bulb
carefully. It may shatter if it is
scratched or dropped. Grasp the bulb
only by its plastic base and do not
touch the glass part. The oil from
your hand could cause the bulb to
break the next time the headlamps
are operated. Keep the bulb out of
children's reach.
*
[SV39100(ALL)01/95]
Do not remove the burned-out bulb unless you
can immediately replace it with a new one. If a
bulb is removed for an extended period of time,
contaminants may enter the headlamp housing
and affect its performance.
[SV39250(ALL)11/92]
one third page art:0000345-A
Parts of a headlamp
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

316
*
[SV39300(ALL)03/95]
To remove the headlamp bulb:
*
[SV39350(ALL)08/95]
1. Make sure that the headlamp knob is in the
OFF position.
[SV39401(ALL)04/95]
2. Lift the hood. If you are replacing the
driver's side headlamp, unclip the electronic
module on the right side of the battery and
move it out of the way. Find the bulb in the
headlamp socket.
[SV39425(ALL)04/95]
one third page art:0001437-A
The module behind the driver's side headlamp
*
[SV39450(ALL)02/95]
3. Remove the electrical connector from the
bulb by pulling the connector.
*
[SV39501(ALL)02/95]
4. Remove the bulb retaining ring by rotating it
counterclockwise (when viewed from the
rear) about an eighth of a turn to free it
from the bulb socket, and by sliding the ring
off the plastic base. Keep the ring. It is to be
used again to retain the new bulb.
[SV39550(ALL)02/95]
5. Carefully remove the bulb from its socket by
gently pulling it straight back out of the
socket. Do not turn the bulb while you
remove it.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

317
*
[SV39601(ALL)03/95]
To install a bulb:
*
[SV39650(ALL)02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV39701(ALL)02/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstopº.
*
[SV39750(ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV39800(ALL)02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
%*
[SV39850(ALL)02/95]
Aiming Headlamps
[SV39901(ALL)02/95]
Your vehicle is equipped with a Vehicle
Headlamp Aim Device (VHAD) on the
headlamp reflector extension and headlamp
housing. Each headlamp may be properly aimed
in the horizontal direction (left/right) and the
vertical direction (up/down) by performing the
steps outlined in the following paragraphs. The
horizontal aim must be adjusted first.
*
[SV39950(ALL)02/95]
Tools required: One 4mm box wrench or open
end wrench.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

320 [SV40800(ALL)02/95]Each 0.1 inch difference in surface height
between the front and the rear wheels
corresponds to0.053Ê ofsurface slope; each0.19Ê
of surface slope corresponds to 0.36 inches
difference in surface height between the front
and rear wheels.
[SV40820(ALL)02/95]
Replacing the High-Mount Brakelamp Bulb
[SV40830(ALL)04/95]
If you have the sedan, your vehicle has a
brakelamp mounted in the rear window, called a
high-mount brakelamp. The wagon has a
high-mount brakelamp on the outside. You may
need to remove this lamp to replace the
brakelamp bulb.
[SV40832(ALL)11/94]
one third page art:0000623-D
Parts of the high-mount brakelamp (sedan)
[SV40835(ALL)11/94]
Sedan
*
[SV40840(ALL)03/95]
To remove the brakelamp:
[SV40842(ALL)11/94]
1. Remove the package tray trim.
[SV40844(ALL)11/94]
2. Push the attachment toward the rear
window.
[SV40846(ALL)11/94]
3. Slide the brakelamp up and away from the
rear window to remove it from the tabs that
hold it down.
[SV40849(ALL)11/94]
4. Disconnect the bulbs.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

321 [SV40850(ALL)11/94]
To install the brakelamp:
[SV40855(ALL)11/94]
1. Install the bulbs.
[SV40860(ALL)11/94]
2. Position the brakelamp over the tab slots
and line up the tabs with the tab slots.
[SV40865(ALL)11/94]
3. Push down and toward the rear window to
engage the tabs.
[SV40870(ALL)11/94]
4. Push attachment toward the rear window
and line up the slot in the attachment with
the edge of the sheet metal hole.
[SV40875(ALL)11/94]
5. Release the attachment slot onto the sheet
metal hole.
[SV40878(ALL)02/95]
6. Replace the package tray trim.
[SV40880(ALL)11/94]
Wagon
[SV40885(ALL)02/95]
one third page art:0001396-A
Parts of the high-mount brakelamp (wagon)
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

322
*
[SV40890(ALL)03/95]
To remove the brakelamp:
[SV40895(ALL)11/94]
1. Remove the interior trim panel.
[SV40905(ALL)11/94]
2. Remove the four attachment nuts that hold
the brakelamp in place.
[SV40910(ALL)11/94]
3. Lift the whole assembly off of the vehicle
from the outside.
[SV40915(ALL)11/94]
4. Disconnect the bulbs.
[SV40920(ALL)11/94]
To install the brakelamp:
[SV40925(ALL)11/94]
1. Install the bulbs.
[SV40930(ALL)11/94]
2. Position the brakelamp into the tailgate
holes.
[SV40935(ALL)11/94]
3. From the inside of the vehicle, install and
tighten the four nuts that hold the
brakelamp in place.
[SV40940(ALL)11/94]
4. Install the interior trim panel.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995