1996 Mercury Sable lock

209
*
[DR21000(ALL)03/95]
By moving the vehicle backward and forward,
you may gain enough momentum to move out
of the spot. Do not rock the vehicle for more
than a few minutes. This may overheat the
engine, damage the transaxle, or damage the
tires. If you are still stuck after a minute or two
of rocking, call for a tow truck.
%*
[DR21200(ALL)01/95]
High water
*
[DR21300(ALL)01/95]
Do not drive through flooded areas unless you
are sure that the water is below the bottom of
the wheel rims.
*
[DR21400(ALL)04/94]
If you must drive through high water, drive
slowly. You may have limited traction or wet
brakes, so allow extra stopping distance because
your vehicle will not stop as quickly as usual.
*
[DR21500(ALL)01/95]
After you drive through the standing water,
apply your brakes gently several times as your
vehicle moves slowly. This helps to dry the
brakes.
%
*
[DR21600(ALL)03/95]
Driving With a Heavy Load
*
[DR21700(ALL)01/95]
There are limits to the amount of weight your
vehicle can carry or tow. The total weight of
your vehicle, plus the weight of the passengers
and cargo, should never be more than the Gross
Vehicle Weight Rating (GVWR). Also, the weight
that your vehicle carries over the front axle and
rear axle should never be more than the Gross
Axle Weight Rating (GAWR) for the respective
axle.
%*
[DR21800(ALL)01/95]
You can find your vehicle's GVWR and GAWR
on the Safety Compliance Certification Label on
the left front door lock facing or on the door
latch post pillar.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

211
*
[DR22050(ALL)01/95]
2. Then weigh your vehicle with the driver,
passengers and luggage.
*
[DR22055(ALL)01/95]
3. Subtract the first reading from the second to
figure the total weight of the load.
*
[DR22060(ALL)01/95]
After determining this load, you must also make
sure that the total weight of your vehicle, plus
the load it carries, is less than its GVWR. Also,
make sure that the weight your vehicle carries
over each axle is less than the GAWR for the
respective axle.
*
[DR22065(ALL)01/95]
You can find the GVWR and GAWR on the
Safety Compliance Certification Label on the left
front door lock facing or the door latch post
pillar.
*
[DR22070(ALL)01/95]
If your vehicle exceeds the GVWR, remove cargo
from your vehicle accordingly. If your vehicle
exceeds the GAWR for either axle, shift the load
or remove cargo accordingly.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

224 [RE06400(ALL)02/95]
one third page art:0000392-BThe temporary spare tire in the wagon
[RE06700(ALL)11/94]
To remove the cover for the temporary spare
tire in the wagon:
[RE06800(ALL)04/95]
1. Twist the three fasteners 90 degrees into a
vertical position.
[RE06900(ALL)02/95]
2. Lift the the cover to disengage the three
retainers.
[RE07000(ALL)05/94]
3. Pull the front of the cover out slightly and
remove the cover by sliding it toward the
front of the vehicle.
[RE07100(ALL)01/89]
4. Lift out the spare tire, jack, and lug wrench.
%*
[RE07400(ALL)03/95]
Preparing to Change the Tire
*
[RE07500(ALL)05/94]
You should only raise your vehicle with a jack
properly placed at the front or rear jacking
points.
*
[RE07600(ALL)03/95]
1. Make sure that your vehicle will not move
or roll. Put the gearshift in P (Park). Set the
parking brake and block the wheel that is
diagonally opposite the tire that you are
changing.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

225
*
[RE08400(ALL)11/94]
RWARNING
When one of the front wheels is off
the ground, the transaxle alone will
not prevent the vehicle from moving
or slipping off the jack, even if the
vehicle is in P (Park). To prevent the
vehicle from moving when you
change a tire, block (in both
directions) the wheel that is
diagonally opposite to the tire being
changed. If the vehicle slips off the
jack, you or someone else could be
seriously injured.
*
[RE08800(ALL)02/95]
2. Get out the spare tire and jack.
*
[RE08850(ALL)05/94]
RWARNING
To avoid injury, never run the engine
with one wheel off the ground when
changing a tire, or at any other time.
The wheel still on the ground could
cause the vehicle to move.
[RE08900(ALL)02/93]
3. Remove wheel covers or aluminum wheel
ornaments with the tapered end of a wheel
nut wrench. Insert the handle of the wrench
between the wheel and ornament and twist
it against the inner wheel cover flange.
*
[RE09200(ALL)01/95]
4. Loosen each wheel lug nut one-half turn
counterclockwise, but do not remove them
until the tire is raised off the ground. You
should pull up on the handle rather than
push to develop maximum force to loosen
wheel lug nuts. SeeAnti-Theft Wheel Lug
Nutslater in this chapter for information on
removing anti-theft lug nuts.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

226
*
[RE09250(ALL)03/95]
Removing and Replacing the Tire
%*
[RE09300(ALL)11/94]
1. Find the jack notch next to the door of the
tire that you are changing. Put the jack in
the jack notch and turn the handle of the
jack clockwise until the wheel is completely
off the ground.
*
[RE09500(ALL)03/95]
RWARNING
To lessen the risk of personal injury,
do not put any part of your body
under the vehicle. Do not start the
engine when your vehicle is on the
jack. The jack is only for changing
the tire in emergencies. Never raise
your vehicle by using a bumper jack.
The bumper system could be
damaged or the jack could slip and
you could be injured.
[RE10000(ALL)02/95]
half page art:0000394-C
The notches for the jack
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

227 [RE12000(ALL)11/94]
2. Remove the lug nuts by using a lug wrench.
Never loosen the hub nuts. See the picture
later in this section if you are not sure where
to find the lug nuts.
*
[RE12005(ALL)07/94]
RWARNING
Your vehicle has been built with
metric (12 mm) threads on the wheel
studs and lug nuts. Make certain,
during wheel removal, the same nuts
removed are reinstalled, or if
replaced, nuts with metric threads
and the same chamfer configuration
are used. Installation of an improper
thread nut on a metric stud will not
properly secure the wheel to the hub
and will damage the stud so that it
must be replaced. Damaged studs
may result in wheel separation and
personal injury.
*
[RE12100(ALL)01/95]
3. Replace the flat tire with the spare tire,
making sure that the air valve stem is facing
outward.
*
[RE12200(ALL)03/95]
4. Reinstall the lug nuts, tightening until the
wheel is snug against the hub. The beveled
edges on the lug nuts face inward. Do not
fully tighten the lug nuts until you lower the
vehicle. If you do, you could force the
vehicle off the jack.
*
[RE12300(ALL)02/95]
5. Lower the vehicle by turning the jack handle
counterclockwise.
*
[RE12400(ALL)01/95]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration. As soon as possible, have your
dealer or a qualified service technician check
the lug nuts for proper torque specifications.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

228 [RE12500(ALL)12/91]
one third page art:0000395-BThe lug nuts on the wheel
*
[RE12600(ALL)11/94]
7. Place any wheel covers and ornaments in the
trunk.
*
[RE12700(ALL)03/95]
8. Put the tire, jack, and wrench away. Make
sure the jack is securely fastened so it does
not rattle when you drive.
*
[RE12750(ALL)03/95]
9. Unblock the wheels.
[RE13007(ALL)04/95]
Removing and Replacing Wheel Covers
[RE13008(ALL)04/95]
Your vehicle may have wheel covers with a wire
retention system.
[RE13009(ALL)03/95]
To remove the wheel cover:
[RE13010(ALL)04/95]
Pry it loose by carefully inserting the tapered
end of the jack handle between the wheel cover
and the wheel.
[RE13011(ALL)04/95]
To replace the wheel cover:
[RE13012(ALL)04/95]
1. One of the windows on the wheel cover is
identified with a valve stem logo on the
back side of the cover. Install the wheel
cover to the wheel with the window at the
valve stem.
[RE13013(ALL)04/95]
2. Hold the wheel cover in this position and
press the cover onto the wheel with the
palm of your hand. Do not force or hammer
the cover.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

230 [RE13050(ALL)04/95]To replace the wheel cover:
[RE13070(ALL)11/94]
1. Reinstall the pedestal on the wheel before
reinstalling the wheelcover.
[RE13080(ALL)11/94]
2. One of the windows on the wheelcover is
identified with a valve stem logo on the
inside of the cover. Align this valve hole on
the wheelcover with the valve stem on the
wheel. Reinstall the cover by pressing with
the palm of your hand. Do not use excessive
force. Do not use a hammer.
[RE13090(ALL)11/94]
3. Attach the bolt to the pedestal through the
center hole in the cover with the lug wrench.
[RE14000(ALL)11/94]
4. Align the legs of the center ornament with
the slots on the wheel cover. Reinstall the
ornament by pressing with the palm of your
hand. Do not use excessive force. Do not use
a hammer.
%*
[RE14100(ALL)03/95]
Anti-Theft Wheel Lug Nuts (If equipped)
[RE14200(ALL)03/95]
If your vehicle has this feature, one of the lug
nuts on each wheel lock must be removed and
replaced with a special key. The key and
registration card are attached to the lug wrench
and stored with the spare tire. If you lose the
key, send the registration card to the
manufacturer (not to the dealer) to get a
replacement key.
*
[RE14250(ALL)03/95]
NOTE: If entire lug wrench/lug nut key
assembly is lost, see your nearest Ford
or Lincoln-Mercury dealer who has
access to a master set of keys.
[RE14275(ALL)11/94]
DO NOT USE THE KEY WITH AN IMPACT
WRENCH.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995